My 47lg50 tv the color of the display is like if it's in 3d mode and distorted and has lines on one side .can any body help me figure out if I need a new board

The symptoms you are describing with your Samsung plasma TV are consistent with a failure of the plasma display panel or a failure of the plasma drivers that control the display Here are a few things you can try to troubleshoot the issue:

1. Check the connections: Make sure all the cables and connections to the TV are secure and not damaged. Loose or damaged cables can cause visual distortions on the screen.
2. Perform a factory reset: Sometimes a factory reset can fix issues with the TV. Refer to the TV manual for instructions on how to perform a factory reset.
3. Check the internal components: If you have experience working with electronics, you can try opening the TV and checking for any obvious damage or loose components. However, be aware that opening a TV can be dangerous and may void the warranty.

Search Results

Troubleshooting Distorted Pictures - Stereo & Video Repair ...

www.stereoandvideorepairco.com/.../DistortedPictureTroubleshooting.ht...
Usually, this occurs on CRT projection TV's, and occasionally on CRT ... Dark, light, or colored bars can be seen rising slowly through the picture, ... Known as "hum bars" or "common-mode noise," these result from AC power line hum coming ...

Flat Screen TV Has Lines Going Through Screen - Possible ...

removeandreplace.com/.../flat-screen-tv-has-lines-going-through-screen-...
Jun 17, 2015 - Flat Screen TV Has Lines Going Through Screen - Possible Bad ...inch LCD TV which is showing lines (vertically) and getting extremely hot. ..... If you leave the projection TV on for a certain amount of time does it ..... If so the plasma gas is most likely causing the screen to become distorted or color issues.

Distorted Colors in an LCD Projector ' Business ...

yourbusiness.azcentral.com/distorted-colors-lcd-projector-8597.html

Common easy LCD TV fix: bad picture screen rainbow colors

? 4:04
https://www.youtube.com/watch?v=KWIWeESmXC0
Aug 10, 2014 - Uploaded by Tampatec
Common easy lcd tv service repair fix, TV's distorted rainbowpicture screen fixed by ... Common easy LCD TV fix: bad picture screen rainbow colors ... Need to report the video? ... Sanyo LCD with Distorted Half Picture Lines Waves Distortion Distorted ...Duration: 11:36. by Do It With Dave 316,733 views.

LCD Display Symptoms and causes. - YouTube

? 2:01
https://www.youtube.com/watch?v=DedJvyNm_s4
Mar 1, 2011 - Uploaded by Grants Pass TV Repair
With LCD TVs you can have the same display problems fordifferent ... Fix for Samsung lcd TV colour display problem - Duration: 1:26. by alwaysafix 462,823 views. 1:26. Sanyo LCD with Distorted Half Picture Lines Waves Distortion ... HOW TO FIX LED TV VERTICAL LINES ON SCREEN 55" MODEL LG ...

How To Fix A Broken Flat Screen LCD LED TV With Lines or ...

All projection TV sets have two very common problems. One is convergence ( 3D/Warped video or dead set) the other is CRT fluid ( Dull Video). Here are more details and solutions for both.

Common Problem #1) Convergence has gone out

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. In some cases the TV will also not show any video. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

• Screen looks 3D, wavy, or has a shadow or shadows
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some pics of convergence problems.





SOLUTION

You can get the correct parts, step by step photo instruction guides, and support from www.TvRepairKits.com or click here

Common Problem #2) CRT Fluid is Cloudy

Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.

Picture of a set that needs the fluid changed.


TV set after fluid change



SOLUTION

You can get the correct parts, step by step photo instruction guides, and support from www.TvRepairKits.com or click here

The tv have a problems known as a convergence problems,it dead.Tv have colors lines R,G,B mis alignments,have colors shadows pictures or 3D pictures look alike?The tv convergene board have dead 2 STK convergence ICS and some or all of it resistors are dead too.These parts on the tv convergence board,must be replaced to solved the tv convergence picture problems.The shop,will cost u like $300-350 for parts and labors.

The tv have a problems known as a convergence problems,it dead.The tv colors lines R,G,B mis alignments anywhere in the pictures,have colors shadows pictures or 3D pictures look alike?The tv convergence board have dead 2 STK convergence ICS and some or all of it resistors too.These parts on the tv convergence board,require replacing to fix the tv convergence board,to solved the tv convergence picture problems.The shop,will cost u like $300-350 for parts and labors.

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

Convergence problems are very common on all Projection TV sets including Sony, Samsung, JVC, Philip Magnavox, Panasonic, Akai, Pioneer, Hitachi, Zenith, and others. You can get a convergenece repair kit from the link below.

Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on - TV may also make a chirping noise.

Here are some photos of convergence problems.





Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a solution

CONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you know what you are doing. If you have never done this before we would advise calling a shop or if you want to do it yourself get a complete kit with instructions and support from www.TvRepairKits.com

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.
This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....
•Screen looks 3D
•Colors don't line up
•One or more colors can't be adjusted when using the convergence menu.
•Screen is bowed or warped.
•TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.

Here are some photos of convergence problems






CONVERGENCE SOLUTION

You can see some more examples and find a fix using this link on Fixya - CLICK HERE

Need the model number to help as I am not sure of you have a RCA or a Toshiba

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

Convergence problems are very common on all Projection TV sets including Sony, Samsung, JVC, Philip Magnavox, Panasonic, Akai, Pioneer, Hitachi, Zenith, and others. You can get a convergenece repair kit from the link below.

Common Symptoms include....

• Screen looks 3D
• Colors don't line up
• One or more colors can't be adjusted when using the convergence menu.
• Screen is bowed or warped.
• TV shuts off after powering on - TV may also make a chirping noise.

Here are some photos of convergence problems.





Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a solution

CONVERGENCE SOLUTION

You will need to replace the convergence chips and possibly some convergence resistors and pico fuses.
This is a a fairly easy DIY job if you know what you are doing. If you have never done this before we would advise calling a shop or if you want to do it yourself get a complete kit with instructions and support from www.TvRepairKits.com