Question about Samsung Office Equipment & Supplies

1 Answer

Samsung 2525W laser gives error message "cover is open"

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Samsung Master
  • 1,316 Answers

Change the microswitch afferent the cover is open.

Posted on Mar 31, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: Document Cover Open

I had the same problem with mine. Lift the top scanner, and check the hinges on the left. That error message means that the little black sensor on the left next to the hinges is not meeting flat with the unit when closed. Hold the sensor in for a few seconds, and your printer will start working properly.

Posted on Jul 09, 2008

  • 1 Answer

SOURCE: error message inner cover is open canon pixma mp610 printer

Had the same problem myself but discovered that I had previously moved the inside flap down when I put the ink in. I moved this back into position and bingo! (If you make sure all the covers are closed then look into the printer where the paper exits you will see the flap that moves up and down, this must be in the up position)

Posted on Jan 31, 2009

  • 105 Answers

SOURCE: Our HP Color Laser Jet 4700 dn frequently gives an

There is either a small piece of paper in your paper input section or you have a paper sensor going bad.

Posted on Nov 20, 2009

aviral_srms
  • 1216 Answers

SOURCE: my laser printer gives message open heat error

This is most commonly caused by a failure of the Fuser unit.
However, in rare circumstances, this can be caused by the Fuser Control section of the SMPS, or the fuser temperature monitoring circuit on the Main Board.
There is a closed control loop:
1. AC voltage is supplied to the Heat Lamp in the Fuser from the Fuser Control section of the SMPS
2. The temperature of the fuser heat is monitored by a thermistor (mounted on the Fuser) connected to the Main Board.
3. The Main Board determines if the fuser temp is too low, correct, or too high and signals the Fuser Control to increase, maintain, or decrease the AC voltage to the Fuser
sorry io say but you had to replace the fuser
call dell costumer support and tell your model no. ask for fuser replacement and they will do it .
Hope your printer is in guarantee period otherwise you had to pay.
REGUARDS

Posted on Feb 07, 2010

  • 2 Answers

SOURCE: Samsung ML-2525W monochrome laser printer;

I have the same problem with mine - first job usually prints but no go on the second one. It tells me the printer is "offline". In some cases I can't even power cycle normally. I have to unplug the back cord and plug it back in, then I can power back on.
I called Samsung today 1-800-726-7864 and was told the printer will need to be taken to a repair center for service. Wish I had better news.

Posted on Apr 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you do a factory reset on a Samsung ml-2525w printer?


If you have the install disc for the printer , you could delete from the hard drive and reinstall, If the Data is not installed in the printers memory this should work.

Mar 14, 2015 | Samsung ML-2525W Wireless Mono Laser...

1 Answer

How to clean ML-2525W Mono Laser Printer ?


did you try a different toner cart if you did and it still does this it is your laser unit. try the cartridge first if it still does it then take it to your local samsung dealer.

Aug 28, 2014 | Samsung ML-2525W Mono Laser Printer -...

1 Answer

My printer is giving message that you rear cover is open for that what to do?


SAMSUNG SCX 4521 PRINTER BACK SIDE COVER IS OPPEN SO PLEASE CLOSE THE BACK REAR COVER & CHECK THE PAPPER JAM IN REAR COVER & AFTER CLOSE THE REARE COVER THEN AFTER SEE THE ERROR YOU CHECK THE BACK COVER SENCER & SENCER PCB

May 01, 2014 | Samsung SCX 4521F All-In-One Laser Printer

1 Answer

Won't scan, error message -scanner door is open


Simple solution. I just had the same problem. Make sure the top cover on the left side is snapped in. It wasn't obvious that it was open. They should probably give a better code because it is not the scanner door that is open.

Apr 16, 2013 | Samsung New-scx-3405fw Wireless...

2 Answers

Samsung ML-2525W monochrome laser printer; connected via USB to MacBook Pro. Prt driver 1.00.02. First job prints fine; 2nd job in queue fails to print, and ''Open Print Queue'' indicates ''printer...


I have the same problem with mine - first job usually prints but no go on the second one. It tells me the printer is "offline". In some cases I can't even power cycle normally. I have to unplug the back cord and plug it back in, then I can power back on.
I called Samsung today 1-800-726-7864 and was told the printer will need to be taken to a repair center for service. Wish I had better news.

Apr 25, 2010 | Office Equipment & Supplies

1 Answer

I am getting a System Error E021, what does this mean?


Hi,
In my home office this error message came up, E021. I opened the Printer cover, closed it, unplugged and replugged and got a Paper Jam message. I removed the paper jam and did the cover/plug routine. Now I have a message CHECK PRINTER OPEN AND CLOSE COVER. But I can't find anything wrong! I have been searcing for an explanation of the error message online, but haven't found that either. my printer may be infested by aliens.
The best advice I can give is to reseat the various parts (drum and toners).

Thanks

Aug 17, 2009 | Canon imageCLASS MF8170C All-In-One Laser...

1 Answer

Samsung CLP-300 - Cover Open error message, but covers are closed


Front cover is on the right hand side, back is on the left hand side in the middle, and the top cover is like a little button on top. All the others are little openings.

Dec 02, 2008 | Samsung CLP 300 Laser Printer

3 Answers

Error Message


Hi there,
"Open heat error" ---
open the back cover and you find a two wire connector just near ribbon connector it is thermistor connector the printer is sensing this connector as open or not connected explore and fix.
Good Luck!!!
neo

Sep 19, 2007 | Samsung SCX-4100 All-In-One Laser Printer

Not finding what you are looking for?

Open Questions:

Office Equipment & Supplies Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Office Equipment & Supplies Experts

jasbo
jasbo

Level 3 Expert

2239 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Lawrence Singapore

Level 1 Expert

70 Answers

Are you a Samsung Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...