Trustworthy Expert Solutions

At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.

View Our Top Experts

Bosch WAE20261AU/01 code E5 comes up.I have cleaned all the filters and checked the water inlet flow and it is perfect. Water comes in for 10 seconds and then E5 comes up, and flow stops.

1 Answer

timoboon2

Expert 360 Answers
Posted on Jan 16, 2019

timoboon2

Expert

Joined: Mar 16, 2010

Answers

360

Questions

Helped

154622

Points

959

This then means that the flowmeter is damaged. Please contact Bosch for spare parts.

5 Related Answers

Diane

7 Answers
Posted on Nov 02, 2007

SOURCE: another inlet / drain light cycle interruption problem!

When the water stops too soon, it could be the "over flow" is stuck in the downward position, therefore the dishwasher thinks it's going to over flow. Check that out. Otherwise I'm afraid this sounds like the circuit board is shot.

Miss Midget

Anonymous

249 Answers
Posted on Dec 07, 2007

SOURCE: Duet Washing Machine model ghw9100lw1 FH ERROR CODE

you should here a humming noise, just before water comes in .do you?close eire let me know.

Anonymous

1 Answer
Posted on Sep 09, 2008

SOURCE: BOSCH SPS5462GB/19 No water seems to

Found the problem after stripping down around the main pump area.
The air pipe connected to the pressure switch on the front right hand side is connected to a small plastic box which in turn is connected to the flow pipe that fills the machine,and the box was completely blocked with slug which stopped the pressure switch from operating and so prevented the water input solenoid from opening. Hence no water would come into the machine

Anonymous

1 Answer
Posted on Mar 16, 2009

SOURCE: Haier XQB55-10 : water leakage from inlet hose jointer

Inside the connector is a flat washer and a mesh filter. one side of the mesh filter has a strip/bar across it, this filter goes into the base of the connector with the strip/bar upwards, make sure it is seated in the connector properly.

Then fit the flat washer ensuring that it is clean/undamaged and lying flat at the base of the connector, the mesh filter strip/bar has at either end a small lip, the washer goes underneath the two lips, if it is placed on top of these lips it leaks!

99% positive on this, if not buy another hose!

Anonymous

1 Answer
Posted on Jul 21, 2009

SOURCE: dishwasher stops after 10 minutes inlet/drain light flashing

I had the same problem on a 5 year old model. It was the main pump leaking from a perished seal causing the water protection microswitch to trip. This gives the symptoms you describe exactly. Parts cost from Miele was about £60 for a new seal. Fairly easy to fit.

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

0helpful

1answer

Bosch dishwasher doesn't work. water not coming

Hi Gilgol, The link below is a Bosh Dishwasher list of error codes, I believe your error code is E3....CHEERS..
http://removeandreplace.com/2015/10/09/bosch-dishwasher-error-codes-how-to-clear-what-to-check/
Bosch Dishwasher Error Code E3
Fault Condition: Not filling with water
Repair or Check: If the water supply cut-off valve on the dishwasher is completely open but the dishwasher will not fill with water then shut off the water supply and unplug the dishwasher. Remove the water fill line and check to see if the water inlet screen valve is plugged up. If so then replace the water valve. Cleaning the screen can make the issue worse so always replace if the screen is clogged. The valve can get stuck open from gunk and therefore flood or overfill.
Parts Required: Water inlet valve
Bosch Water Inlet Valve Assembly for Dishwasher

Read full answer

Apr 02, 2016 • Bosch Dishwashers

tip

LG Washing machine IE error code Solutions

An IE error code will appear if the washer has not filled with water in approximately 8 minutes.

Are the water valves opened completely?

If an IE error code appears on the washer, check to make sure both hot and cold-water taps are open completely. After both valves have been opened, unplug the washer for 10 seconds and retry the wash cycle.

Are the inlet hose filters clogged?

There are filters on the inlet hose connections of the washing machine. They are intended to filter away mineral deposits from hard water and other debris from getting into the unit. If clogged, water will not flow through these filters into the washer. Turn off both the hot and cold water taps, disconnect the inlet hoses from the back of the washing machine, and clean the inlet filters gently but thoroughly.

Are the inlet hoses attached properly?

If the inlet hoses are not attached to the machine correctly, it will prevent proper water flow to the washer. Turn off the hot and cold water supply then disconnect and reconnect the inlet hoses. Ensure that they are threaded properly. After the hoses have been reconnected, open the water taps completely, check for leaks, and unplug the washer for 10 seconds and retry the wash cycle.

NOTE: The inlet filters are inside the hose connections on the back of the washer. Because of their small size, take care when removing and cleaning the inlet filters so that they do not break.

Read full tip

on Jun 02, 2011 • Washing Machines

0helpful

1answer

Water tap closed? what does this mean

Water Inlet Flow Meter P/N 00602819 is failing.

For a Bosch Axxis Washer model WFR2460UC --

If both of the water supply valves are open, you cleaned the hose internal strainers, and there are no kinks in the hoses, part "Water Inlet Flow Meter P/N 00602819" is failing. This device measures exactly how much water enters the tub, no matter what the water pressure. Not hard to DIY replace with simple tools.

Read full answer

May 24, 2014 • Bosch Axxis WFL 2060 Front Load Washer

1helpful

2answers

Intermittently get Check Water and E 24 indication.

You may have a defective water inlet valve.

Read full answer

Mar 21, 2017 • Bosch Dishwashers

0helpful

1answer

Water is way too hot. Five year old GWH2400E NG is giving error code EC: Ionization failure during operation. set point temperature = 106, inlet water temp = 88, outlet water temp = 171, water flow = 12,...

Before calling service technician who has service manual and can test which part has failed, open following links for troubleshooting resources including steps below and phone number for Bosch:
http://waterheatertimer.org/Troubleshoot-Bosch-Tankless-water-heater.html
http://www.boschhotwater.com/HelpfulResources/TechnicalSupport/BoschAquaStarModels/2400ETechSupport/Troubleshooting/tabid/1131/Default.aspx

Clean inlet filter
Check all faucets for clear pathway
This unit does not work with preheated water (solar assisted)
Incoming water above 70 degrees, avoid restricted faucets
Check that both temperature sensors are making contact and firmly mounted on respective cold and hot pipes.
Descale heat exchanger
http://www.boschhotwater.com/Portals/7/TechBulletins/TWH-G2-13_Descaling.pdf

Read full answer

Aug 16, 2011 • Bosch AquaStar 2400ES-NG

0helpful

1answer

THE SCREEN SHOWS IE

Hello there and thank you for choosing fixya
An IE error code will appear if the washer has not filled with water in approximately 8 minutes. If an IE error code appears on the washer, check to make sure both hot and cold-water taps are open completely. After both valves have been opened, unplug the washer for 10 seconds and retry the wash cycle.
There are filters on the inlet hose connections of the washing machine. They are intended to filter away mineral deposits from hard water and other debris from getting into the unit. If clogged, water will not flow through these filters into the washer. Turn off both the hot and cold water taps, disconnect the inlet hoses from the back of the washing machine, and clean the inlet filters gently but thoroughly.
If the inlet hoses are not attached to the machine correctly, it will prevent proper water flow to the washer. Turn off the hot and cold water supply then disconnect and reconnect the inlet hoses. Ensure that they are threaded properly. After the hoses have been reconnected, open the water taps completely, check for leaks, and unplug the washer for 10 seconds and retry the wash cycle.
And finely if all of this does not work then the inlet valve on the machine needs to be replaced ok?
Hope this all helps

Read full answer

Aug 05, 2011 • LG WM1814CW Front Load Washer

0helpful

2answers

Hi I went to put my Bosch dishwasher on this morning only to find that it would not come on . there was water in the bottom of the dishwasher so i cleaned all the water out and cleaned all the filters...

Hello,
This video will help you fix your ouch dishwasher.

You can also purchaser a repair video here.
http://www.appliancerepairlesson.com

Read full answer

Feb 19, 2011 • Bosch Dishwashers

0helpful

1answer

I had E13 code, followed MacMarkus guides, cleaned the space now no water come to the drum. My Nexxt 500plua is less than 2 year old, but out of warranty. Thank for your help. Le

You might want to install a water filter for your Bosch Axxis washer faucet so you can prevent this from happening again. Remove any sediments or dirt obstructing the flow of water in the hose. Pull the sensor that is located n the inlet valve and check inside to see if anything is trapped. If you are using corrosive water, just replace the sensor. If it still works just fine, then cleaning it will suffice.

Read full answer

Dec 04, 2010 • Bosch 3.81 cu ft WFMC530 1UC Nexxt 500...

2helpful

1answer

My bosch wfk 2401 when i start the wash everything is fine then after a couple of minutes it starts beeping the error code 01. i have checked to make sure the filters are cleaned out and that the water...

Hello and welcome to fixya.

I'll start by saying you're right the "01" error code is indicating a fill problem has been detected by the control.

Have you tried just a "cold" water wash ? If not try selecting "quick wash" and on the dial turn it to #1 "cold" in the cotton setting see what happens. Do the same and select #3 "hot". If the error occurs in one and not the other, observe and either focus on the hot water valve or the cold main wash valve ( I don't think it is the cold prewash valve or the error would occur immediately ).

In fact I suspect it is the main wash cold valve ( dual valve ) since you haven't indicated the error occurs during prewash and the hot water valve is energized in prewash by design to help rinse out the detergent no matter what cycle or temp. you selected.

Having said all that, here's what you're dealing with. Even though you appear to have sufficient water flow as you stated you checked for, the electronic control doesn't think it is correct.
There are several factor's which could possibly be causing this error, a couple you've mentioned.

They are...

Water supply turned off. ( obviously not in this case )

Water inlet hose filters (strainers/screens) blocked. ( you've said you cleaned them out )

Water pressure too low. ( must be no lower than 14.5psi and a max. of 145psi )

Water inlet valve(s) has failed. ( this doesn't appear likely...at least at first, not completely failed based on your description...but the control may think it has. If you have an ohm meter you can check it. the coils should have a value of between 2.7 and 3.3k ohms. That means 2700ohms and 3300ohms. If not within those values the control will detect the value being incorrect , hence displaying the "01" error. Change the valve, Bosch part # 265772, or repairclinic.com # 467537.
The Hot water valve if need be is Bosch part # 171295 or repairclinic.com # 423900 )

Control module has failed. ( Not very likely either...but possible...if not the valves. )

Let me know what you find as I will watch for your reply here. Thanks for visiting "fixya". Please take a moment and rate the info provided for you here today.

Let me know if you require further assistance.

Thanks and good luck.

macmarkus :)

Read full answer

Jun 12, 2010 • Bosch WFK 2401

0helpful

1answer

All filters are clean, but water will not come in

Hi, Check the float in the front corner and make sure it moves up and down freely. Also, you can check voltage at the inlet valve. It should get 120V at the start of the wash cycle. If there is voltage, the inlet valve will need replaced. If there is no voltage, the float switch needs tested. It is usually the inlet valve or the float.
I hope this helps you. Please let me know if I can assist you further.

Vic

Read full answer

Jul 04, 2009 • Bosch 24 in. SMU70 Built-in Dishwasher

Not finding what you are looking for?

View Most Popular

Washing Machines

Bosch dishwasher doesn't work. water not coming

Bosch Dishwashers

141 views

Ask a Question

Usually answered in minutes!

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual

Related Topics:

Trustworthy Expert Solutions

Bosch WAE20261AU/01 code E5 comes up.I have cleaned all the filters and checked the water inlet flow and it is perfect. Water comes in for 10 seconds and then E5 comes up, and flow stops.

1 Answer

timoboon2

5 Related Answers

Diane

Anonymous

Anonymous

Anonymous

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

Bosch dishwasher doesn't work. water not coming

LG Washing machine IE error code Solutions

Water tap closed? what does this mean

Intermittently get Check Water and E 24 indication.

Water is way too hot. Five year old GWH2400E NG is giving error code EC: Ionization failure during operation. set point temperature = 106, inlet water temp = 88, outlet water temp = 171, water flow = 12,...

THE SCREEN SHOWS IE

Hi I went to put my Bosch dishwasher on this morning only to find that it would not come on . there was water in the bottom of the dishwasher so i cleaned all the water out and cleaned all the filters...

I had E13 code, followed MacMarkus guides, cleaned the space now no water come to the drum. My Nexxt 500plua is less than 2 year old, but out of warranty. Thank for your help. Le

My bosch wfk 2401 when i start the wash everything is fine then after a couple of minutes it starts beeping the error code 01. i have checked to make sure the filters are cleaned out and that the water...

All filters are clean, but water will not come in

Not finding what you are looking for?

Washing Machines

Bosch dishwasher doesn't work. water not coming

Ask a Question

Top Bosch Washing Machines Experts

Brad Brown

NOEL

Oliver Street

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Manuals & User Guides

BOSCH WFL 1262 ZA.pdf....

BOSCH WFL 1262 ZA.pdf....

Wfvc5400uc__vision_500_series_front...

Related Topics:

Trustworthy Expert Solutions

Bosch WAE20261AU/01 code E5 comes up.I have cleaned all the filters and checked the water inlet flow and it is perfect. Water comes in for 10 seconds and then E5 comes up, and flow stops.

1 Answer

timoboon2

5 Related Answers

Diane

Anonymous

Anonymous

Anonymous

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

Bosch dishwasher doesn't work. water not coming

LG Washing machine IE error code Solutions

Water tap closed? what does this mean

Intermittently get Check Water and E 24 indication.

Water is way too hot. Five year old GWH2400E NG is giving error code EC: Ionization failure during operation. set point temperature = 106, inlet water temp = 88, outlet water temp = 171, water flow = 12,...

THE SCREEN SHOWS IE

Hi I went to put my Bosch dishwasher on this morning only to find that it would not come on . there was water in the bottom of the dishwasher so i cleaned all the water out and cleaned all the filters...

I had E13 code, followed MacMarkus guides, cleaned the space now no water come to the drum. My Nexxt 500plua is less than 2 year old, but out of warranty. Thank for your help. Le

My bosch wfk 2401 when i start the wash everything is fine then after a couple of minutes it starts beeping the error code 01. i have checked to make sure the filters are cleaned out and that the water...

All filters are clean, but water will not come in

Not finding what you are looking for?

Washing Machines

Bosch dishwasher doesn't work. water not coming

Ask a Question

Popular Questions

Pump Blocked - Cannot open/remove cap

E17 error code

Bosch Washing MAchine - E2 error message

I have E3 error code on a Bosch washing machine

Bosch washer door won't open after wash is done

Top Bosch Washing Machines Experts

Brad Brown

NOEL

Oliver Street

Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

Manuals & User Guides

BOSCH WFL 1262 ZA.pdf....

BOSCH WFL 1262 ZA.pdf....

Wfvc5400uc__vision_500_series_front...