Question about Washing Machines

Open Question

I have a problem on my washing machine ii E4 error code (Master Brand).After restarting this machine,this code still on.How to slove my problem. Thanks regards,

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 11 Answers

SOURCE: Error codes

First empty the machine by lowering the hose at the rear to ground level into a container. Take off the white plastic cover on rear at bottom. You will see black rubber hose connected to barrel of machine in right hand corner. Undo the silver screw on the band securing the hose. (Biggest band). You can now pull the hose down to reveal a "table tennis like" ball. Lift it out carefully and you will probably find an obstruction like a coin or similar. I found a hairgrip but it was enough to stop the ball functioning. DO NOT TAKE OFF THE WHITE HOSE CLIPS

Posted on Feb 02, 2008

Ad
  • 706 Answers

SOURCE: LG-Trom Getting error CL .now not able to operate.after switch on it gives CL in display

IE is a water inlet error...meaning that the correct water level was not achieved within 8 minutes or it did not reach preset water level within 25 minutes...

CL is child lock feature which can be toggled on and off by by holding the Pre wash button in for 3 seconds.. Hope that helps...

Posted on Aug 17, 2008

  • 1 Answer

SOURCE: error code 43 on F& P washing machine

The micro switch or the lever that activates it seems to have been the cause of the Error Code 43. Have re-seated the switch in its holder and ensured the activating (out of balance) lever is moving freely. The switch appears to be OK and now it is all re-assembled, the Error Code 43 is gone. Machine is operating normally again.

Out of Balance Switch was located below the right hand side of the computer board (module).

Rgdz John T

Posted on Sep 20, 2008

  • 1 Answer

SOURCE: Dishwasher problem powerpoint IDW12

clean the filter on the intake pipe, just done mine.

Posted on Dec 02, 2008

  • 10 Answers

SOURCE: My brand new Bosch is not draining and is showing E:13 error code

Put the washer on cold and run "TWO" cycles. There is too much soap or fabric softner.

Posted on Nov 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Samsung front load washing machine model wf42h5000a. During rinse cycle machine stops and displays error code e4 and Cannot be reset.explain error code. What are possible solutions ?


hi Judi.
this is what i found.

If your Samsung washing machine is displaying a E4/error code on the control panel after completing the spin cycle and the clothes are still wet, we've got the solution for you. This fault is most commonly caused by an unbalanced washing machine load.

Samsung Washing Machine E4/UE Error Code ' eSpares

https://www.espares.co.uk/advice/symptom/samsung-washing-machine-e4ue-error-code
What does 4e mean on my Samsung washing machine?This is essentially a fill timeout error which will normally mean that either the water isn't on or that an inlet valve has failed or pressure switch problem check pipes as well. Water fill time out: The washing machine has failed to fill with water in a reasonable time.24 Nov 2015Samsung washing machine error code 4E and E1 Fault Not filling in ...https://www.youtube.com/watch?v=cFlnxeB0P0gSearch for: What does 4e mean on my Samsung washing machine?
or try this link.
Samsung front load washing machine error code e4 Google Search

Nov 27, 2017 | Samsung Washing Machines

1 Answer

E4 error code on electrolux washing machine ewt 854s


E4 is the pump is blocked {not running} pehaps a hair pin or clothing wires get stuck
fully drain it and take the filter out

and clean it


these error codes are similar to candy
youll get an idea from this video
https://www.youtube.com/watch?v=kzhlvB2LjXg

Nov 28, 2014 | Electrolux EW1000i Front Load Washer

1 Answer

Samsung trouble shooting


The E4 is an error code. What the washing machine "is trying to communicate" to you is that it has detected a load imbalance at the clothes being washed; thus it won't be able to spin at full speed. Maybe it stops waiting for you to distribute the clothes more evenly. See more about error codes at http://www.ukwhitegoods.co.uk/help/fix-it-yourself/fault-codes/laundry-fault-codes/3069-samsung-washing-machine-fault-codes.html.

Aug 28, 2014 | Washing Machines

2 Answers

Defy fuzzy top loader DTL139 has a EC error code


I need assistance with pressure switch e4 error

Jul 19, 2014 | Washing Machines

1 Answer

Got a logik washing machine error code e4. what the problem thanks


My washing machine in a logik and is displaying a E4 error code any now what's wrong wiv it

Jan 13, 2012 | Washing Machines

2 Answers

The washeer machine give a error code E4


A code of E4 means that there is to much suds or the pump is blocked. use less detergent and get detergent with he in the title. turn to off and try to restart the drain to correct problem.

You will find the code in the manual. If you do not have let me know I will send you one here.

Good Luck And Please Rate FixYa!

Dec 19, 2008 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Brad Brown

Level 3 Expert

18108 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...