Question about HP Office Equipment & Supplies

1 Answer

NHp Laserjet P3005 print blank after changing almost all the parts. still printing blank on paper, what could be wrong

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • HP Expert
  • 394 Answers

Check the seal strip has been removed from the cartridge.
Check there is nothing obscuring the laser scanner window (usually located in the top of the cartridge chamber)

Posted on Jan 25, 2019

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
EPIJAB
  • 89 Answers

SOURCE: Printer prints blank on paper

Open the door half way through a page print and pull out toner cartridge. The page should be in the toner cartridige. If you can see the printed image then the fuser is the problem if you see nothing then the toner is bad or has a protective sleeve inside that needs to be pulled out from one of the ends.

Posted on Jan 08, 2009

Muggs01
  • 72 Answers

SOURCE: HP Laserjet 2200 Keeps Spewing Out Blank Paper

sounds like it has a solinoid that is stuck open.

Posted on Jan 16, 2009

  • 150 Answers

SOURCE: hp p3005 - Excess Toner Along Edge

you need a new cartridge

Posted on Jan 06, 2010

brett207
  • 231 Answers

SOURCE: the printer keeps printing in landscape form even

This sounds like a software problem...

Try using the PCL5e driver instead.

Posted on Jan 27, 2010

  • 10 Answers

SOURCE: HP LaserJet P3005 printer prints wrinkled paper

2 reasons:
1. Was there a paper jam prior to this problem? It could be that the paper was pulled out and a small bit of it is stuck on the pins that guide the paper from the heat roller. If no torn jammed paper prior to this issue, then check out 2.

2. the heater/roller is damaged and needs to be replaced. I would suggest you take it to your nearest HP dealer to properly diagnose this for you.This would save you unnecessary cost in trying to pull it apart and causing more damage to it.

Good Luck,

Posted on Jan 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HP laserjet p3005 it was working ok as we don=ont change the settings often. From yesterday, as soon as we give a print command, it gives a message "LOAD TRAY 1 LIGHT LETTER, then when we press green...


This is a settings problem, you will need to go through the paper handling menu on the printer and on your computer to ensure they are set to the correct paper size that you are trying to print on.

Aug 10, 2011 | HP LaserJet P3005 Printer

1 Answer

Getting blank print outs with one base line printed of symboles and letters mixed in Hp laserjet P3005.


The two most common problems that cause this are:

1. bad cabling. Check and make sure cables are properly seated and try a different cable if you have one.

2. wrong or corrupted print driver, try uninstalling and reinstalling the driver for the printer.

Jul 08, 2011 | HP LaserJet P3005n Printer

1 Answer

Jam inside top cover 13.05.00 also change fuser assembly


To remove paper jam. Just remove the toner cartridge and pullout jammed paper. If still coming paper jammed error message. Switch of the printer and the printer will roll over the paper jammed.

Changing of fuser drum is required if the print out came with the black strips. This happens when you print large volume of printing jobs.

Nov 26, 2010 | HP LaserJet P3005 Printer

2 Answers

My HP P3005 prints blank pages


Please check the cartridges it see if the toner is finish,clean the print head because it may be block up or you can replace it if it is damage.

Aug 15, 2010 | HP LaserJet P3005 Printer

1 Answer

LJ P3005, will not print from tray 2. Tray 2 is


Do a factory reset then reconfigure device one more time.

Jan 24, 2018 | HP LaserJet P3005n Printer

1 Answer

Verticle lines printing on laser printer


Check the fuser. If it is the fuser, you should be seeing 3 dark lines on the fuser film. Here is the picture about how the film looks like:
d0e1b68.jpg

Changing the film usually solve the problem. However changing the film itself is difficult. You have to remove and basically disasseble the fuser, and change the film. However it is fairly cheap and if you decide you would like to save some money, here is the link available in ebay:
http://cgi.ebay.com/Fuser-Film-Sleeve-HP-LaserJet-P3005-RM1-3740-/250558576965?cmd=ViewItem&pt=BI_Toner&hash=item3a56747945


Or, simply search for 'P3005 Fuser Film' and you will find a lot.

Other than that, you can change the entire fuser. Please note that fuser for P3005 is not consumer installable part. You still have to take out some parts in order to change the fuser.

The parts are available from many parts supplier. Simply google 'P3005 fuser'. Usually around $100 for a refurbished fuser.

You can also recycle your old fuser and get some moeny! (about $15-$25 per fuser).

Good luck!

Apr 09, 2010 | HP LaserJet P3005n Printer

2 Answers

Hp 3005dn prints blank pages, even the configuration pages requested from the machine itself


if you haven't any error message then you may have a problem in laser shutter, check and reseat your catrtidge, or you have a problem in your DC Controller

Apr 01, 2010 | HP LaserJet P3005 Printer

1 Answer

HP LaserJet P3005 printer prints wrinkled paper


2 reasons:
1. Was there a paper jam prior to this problem? It could be that the paper was pulled out and a small bit of it is stuck on the pins that guide the paper from the heat roller. If no torn jammed paper prior to this issue, then check out 2.

2. the heater/roller is damaged and needs to be replaced. I would suggest you take it to your nearest HP dealer to properly diagnose this for you.This would save you unnecessary cost in trying to pull it apart and causing more damage to it.

Good Luck,

Jan 27, 2010 | HP LaserJet P3005n Printer

1 Answer

HP P3005 - skid marks along paper's edge


Print 3 pages. Use the manual feed tray. As they print, open the cover, remove the toner and look down at the paper in the printer. Do you see marks along the edge? If no...replace the fuser. If yes...it could be the transfer roller.

Jan 07, 2010 | HP P3005d Monochrome LaserJet Printer

Not finding what you are looking for?

Open Questions:

Office Equipment & Supplies Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

Clive
Clive

Level 3 Expert

4345 Answers

Ekse

Level 3 Expert

13434 Answers

Thomas F. Schneider

Level 3 Expert

2715 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...