Question about Bosch Washing Machines

1 Answer

Logixx8 Bosch washing machine displays F43, detergent and softener drawers were emptied, but clothing not washed, half is wet, the rest dry. What do I do?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

  • Expert
  • 169 Answers

Motor carbon brushes burned out and needs to be replaced. You can YouTube the procedure and do it yourself or call a service center and tell them you know precisely was wrong with it and how much to replace the parts and labor. It's a. 45-60 job
good luck

Posted on Jan 11, 2019

  • 3 more comments 
  • Anonymous Jan 11, 2019

    Thanx so much! Are you saying that F43 means replace carbon brushes? What does 45-60 mean-$?

  • William Bailey
    William Bailey Jan 11, 2019

    Estimate time to make the repair. If you're handy around the house is not very hard to do it yourself

  • Anonymous Jan 12, 2019

    Thanx for your reply! I reset the machine and did a 15min load, which worked but it didn't drain. Is it really the carbon brushes or something else?

  • William Bailey
    William Bailey Jan 13, 2019

    You have a different problem. If the carbon brushes were bad and motor wouldn't function, your problem sounds like a blocked or fail pump.

  • Anonymous Jan 17, 2019

    Turns out it was both the carbon brushes and a blocked drain. Thanx so much for all your contributions!

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
barkencoa
  • 3463 Answers

SOURCE: the fabric softener drawer is

Remove drawer and thoroughly clean, you must have a blockage in it for the water to remain.
Make sure that you clean every piece of it, taking all the components out.
Please leave feedback.

Posted on Dec 01, 2008

barkencoa
  • 3463 Answers

SOURCE: fabric conditioner drawer does not empty

The inlet to the conditioner compartment is probably blocked.
Get a thin piece of flexible wire and make a right angled bend on the end about 1" long, and poke it into all the holes u can see in the top of the dispenser compartment, particularly the ones at the front right side.
This should solve the prob.
Plz rate this solution .
Thanks

Posted on Jan 02, 2009

  • 107 Answers

SOURCE: My clothe come out very wet at the end of the wash cycle

If the pump is clogged and can't release all the water it won't go into final high spin. Remove lower cover and locate coin catch and unscrew it. Water will come out, so be ready. If it's full of stuff, this is probably the problem.

Posted on Mar 13, 2009

  • 1 Answer

SOURCE: Fabric softener stays in drawre

We just had a tech come out to fix this problem for us. Essentially, the problem is that the fabric softener builds up and gets clogged. He cleaned out a solid hunk of frabric softener gunk, and suggested that we dilute our fabric softener with water to keep this buildup from happening again.

Posted on Apr 11, 2009

  • 1 Answer

SOURCE: Hard scratchy towels. Have used all wash cycles, and use fabric softener

have you tried just white vinegar as your rinse aid. Do a full cycle of your washing machine using white vinegar instead of detergent, to clean any residue from pipes, and then in the next wash try white vinegar as your rinse aid.

Posted on Apr 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have front loader washing machine and the rubber has got mould and having difficulty in removing the black mould


  • Saturate an old cloth with white vinegar. Alternatively, you might use petroleum jelly on the cloth to remove the mold.Pull the gasket out gently with your hands to reveal the mold and mildew buildup inside the folds of the gasket.Wipe the mold away from the gasket with the cloth. Continue working to wipe away all mold from the folds of the rubber gasket.Dry the folds of the gasket with a dry cloth when you finish removing the mold.Repeat this procedure at least once per month to prevent mold and mildew from forming. If you notice mold occurring more frequently, clean it off when you see it.


  • Tips for Preventing Mold & Smelly Problems:
    • Always leave the door and dispenser unit slightly ajar after the laundry is done. Front-load washers and the detergent/softener dispenser drawer must dry out.
    • Never leave a wet washload in the washer overnight; remove it when the washing cycle is complete and leave the door open.
    • After a load is done, always rotate the drum with your hand to see and remove all items. Some could be sticking to top or sides of the washer drum.
    • Use softener sheets in the dryer instead of liquid softeners in the washer.
    • Liquid detergents may leave less residue than powdered formulas which may not dissolve properly.
    • Use less than the recommended detergent level for your load. Too much detergent can cause a residue build up. Experiment until you find a minimum measurement that delivers a clean wash. This is also a money saver.
    • Occasionally wash some loads such as whites, linen and towels in warm or hot water to help flush out wash residue.
    • Always clean your washer as per your product manual. High efficiency front-load models have a cleaning cycle and it's imperative that you periodically run this cycle as directed.
    • Check the gasket just inside the door opening and remove any visible debris. You can also wipe it to speed the drying process.
    • Always use HE detergents with high efficiency front-load washers. Specially marked HE laundry detergent is low sudsing and is recommended for these low-water washers.
    • If this advice was helpful a vote with the thumbs up would be appreciated. Thanks.

    Apr 08, 2011 | Ariston Technologies Ariston AWD12 Front...

    1 Answer

    Softener won't empty in Bosch Classixx 1000


    take out the soap drawer clean in hot water inside the machine where you took the soap drawer out at the top look for the hole where the water runs out it may be blocked with mildew dettox mildew spray is very good at breaking all that down spray in leave for a while put soap draw back in and do a wash without clothing as spray contains bleach

    Mar 30, 2010 | Bosch Classixx WFL 2066 Front Load Washer

    1 Answer

    Where to put the detergent and liquod softener in newHaier washer


    Detergent goes in the drum with the clothing, fabric softener in the middle of the agitator, the drawer is for delayed start if using soap powder

    Apr 04, 2017 | Haier XQJ50-31 Top Load Washer

    1 Answer

    Conditioner drawer not emptying


    Do you use a thicker type of softener? When I had this problem with my washer I added water to the softener to thin it out, as it just seems like it leaves a build up that clogs repeatedly otherwise. hope that helps

    Jun 19, 2009 | Bosch Classixx WFL 2066 Front Load Washer

    1 Answer

    Creda Washing Machine Detergent Dispenser not emptying


    does the detergent get wet?
    may be the blue trap door that is behind the detergent in the drawer is set for liquid detergent ie 'closed' and needs to be set to open to allow the powder past. or the holes above the detergent section where the waster comes out are blocked so water goes in another route.
    you could always put the powder straight in with the wash to get yourself out of trouble.

    Feb 03, 2009 | Washing Machines

    2 Answers

    Washing instructions


    My book says for the Axxis WFL 2050/WFL 2060 : from the left while looking at it from the front: detergent for wash, stain remover, middle: fabric softener, fabric conditioner, right one: detergent for soaking agent. (Do not use chlorice bleach in this wasking machine).

    Oct 11, 2008 | Bosch Axxis WFL 2060 Front Load Washer

    2 Answers

    Bosch conditioner drawer


    This problem is caused by the compartment not filling up sufficiently to start the siphon action. First ensure that the drawer is clean, especially the siphon tube then, with the drawer removed, check the top of the compartment. You will find various holes that let in the water, make sure these are clean and not blocked with mould. Clean out with mould remover and wire then run a cycle with no washing or softener/detergent in the machine.

    Aug 01, 2008 | Bosch Classixx WFC 2465 Front Load Washer

    3 Answers

    Fabric softener stays in drawre


    I had this same problem to

    If you take out the drawer of the washing machine and look upwards there are 4 very very small holes get a pipe cleaner and giver them a jolly good clean.

    This should then solve the problem

    Jul 07, 2008 | Bosch Classixx WFL 2066 Front Load Washer

    2 Answers

    Dispenser


    add water to them and then it will work

    Feb 20, 2008 | Bosch WFMC 3200 Front Load Washer

    Not finding what you are looking for?

    Open Questions:

    Washing Machines Logo

    Related Topics:

    59 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Bosch Washing Machines Experts

    Marvin
    Marvin

    Level 3 Expert

    83951 Answers

    Craig Butler
    Craig Butler

    Level 3 Expert

    1730 Answers

    Carmen Mikulic

    Level 2 Expert

    415 Answers

    Are you a Bosch Washing Machine Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...