How do i reset the password on my pendo pad

Bear in mind that this restores to factory defaults. In short, it is like you went out and bought a new one and just opened the box.


Pendo Pad Factory Reset Hard Reset Remove Pendo Pad Password Passkey

Factory reset:

1. Turn the power off and pull the battery out and reinsert it.
2. Hold the Volume Down button.
3. Then press and release the Power button.
4. Wait a minute,the menu appears that allows for Fastbook, Recovery, Clear Storage, and Simlock.
5. Ok,press the Volume Down button to choose Clear Storage.
6. Next,press and release the Power button,Wait for the DoDo Pendo Pad to restart.
7. You will see the two options: Volume Up for YES and Volume Down for NO.
8. If you choose YES, all data will be deleted from your DoDo Pendo Pad and including third-party applications.
9. The DoDo Pendo Pad will reboot to its original data.

contact pendo

Try the first two suggestions from the link pendo pad 7 won boot up

Craig, jump onto YouTube and search on "Pendo Pad Reset" for ideas. Lot's of good stuff out there and standard reset steps for Android devices are covered.

Factory reset!

I have resolved the pendo pad hard reset lack of procedure and can factory reset a pendo pad that is locked with a passkey or and password full factory reset


First download you pendo pad firmware from here

http://shop.pendo.com.au/index.php/su...

I used the generic firmware 1 download and it worked fine for the TPC7SlV
Then Extract the . img file to you computer

Then you will need the firmware update too called rktools found here

http://download1942.mediafire.com/le9...

extract the zip file to your computer


Now your ready to flash the firmware

1. Power off your tablet with the switch
2. Turn the power switch Back the the on Position
3. Press & hold Side Button with the home picture also called the back/esc key
4. While holding, connect PC and tablet with USB cable (if tablet boot normally, try again)
5. Install the driver for your computer included in the RKtools Folder
6. Tablet should be recognized as "RK281X Device" in Windows
7. Start RKAndroidBatchUpgrade from rktools folder
8. In the bottom of the batch RKAndroidBatchUpgrade programme there should be a green light in the device upgrade area. * if there is no light in the upgrade area and all the numbers are grey then repeat the previous steps
9. Under the setting heading click and select the image file you downloaded from pendo ( will be a .img file if its a .zip file you need to extract it)
10.Click the upgrade button
11. wait till operation is completed

BAM Your pendo is password free, i hope i have created the best and easiest way to do this

***Please note if your wireless or Mobile network do not turn on then you have chosen one of the wrong firmware types from the pendo download site !!! the wireless and mobile network hardware are the only distinguishing features between the firmwares apparently******

Hi you will probaslly have to flash the pendo pad, its not too hard to do here are my instructions, - unfortunatly a pendo pad does not have a recovery menu to access on device boot

note - this solution also unlock the pendo pad and restores it to factory settings even if it wont boot the android os



First download you pendo pad firmware from here

http://shop.pendo.com.au/index.php/su...

I used the generic firmware 1 download and it worked fine for the TPC7SlV
Then Extract the . img file to you computer

Then you will need the firmware update too called rktools found here

http://download1942.mediafire.com/le9...

extract the zip file to your computer


Now your ready to flash the firmware

1. Power off your tablet with the switch
2. Turn the power switch Back to the on Position
3. Press & hold Side Button with the home picture also called the back/esc key
4. While holding, connect PC and tablet with USB cable (if tablet boot normally, try again)
5. Install the driver for your computer included in the RKtools Folder
6. Tablet should be recognized as "RK281X Device" in Windows
7. Start RKAndroidBatchUpgrade from rktools folder
8. In the bottom of the batch RKAndroidBatchUpgrade programme there should be a green light in the device upgrade area. * if there is no light in the upgrade area and all the numbers are grey then repeat the previous steps
9. Under the setting heading click and select the image file you downloaded from pendo ( will be a .img file if its a .zip file you need to extract it)
10.Click the upgrade button
11. wait till operation is completed

BAM Your pendo is password free, i hope i have created the best and easiest way to do this

***Please note if your wireless or Mobile network do not turn on then you have chosen one of the wrong firmware types from the pendo download site !!! the wireless and mobile network hardware are the only distinguishing features between the firmwares apparently******

• CategoryHowto & Style
  
• LicenceStandard YouTube Licence
  

i cannot open my pendo pad tpc7slv because it was locked and i dont know how to open it.how to reset it without wifi connection

buy a new pendo pad