How do i enter service mode on Bizhub 3320 - bizhub Konica Minolta Office Equipment & Supplies

2. Failed fuser lamp(s).
Check continuity of the three upper fuser lamps L2, L3 and L4. Check the operation of the three upper fuser lamps in the Service Mode by following the steps below. Replace failed fuser lamp (p/n A03U M31E 12 for bizhub PRO C5500/C5501/C6500/C6500P/C6501/C6501P/C65hc and p/n A1DU M31E 00 for bizhub PRESS C6000/C7000/C7000P/C70hc/bizhub PRO C6000L).
a. Press Utility/Counter.
b. Press "Stop 00" "Stop 01" to access Service Mode.
c. Press State Confirmation.
d. Press I/O Check Mode.
e. Enter code 45 using the numeric keys.
f. Press Access to enter multi mode 11 (L2).
g. Press the START key. Verify the lamp comes ON.
h. Press the STOP key.
i. Press "C" key to enter another multi mode.
j. Repeat steps 6 through 8 for multi mode 12 (L3) and 14 (L5).

SOLUTION: To clear the message:
1. Enter Service Mode.
2. Select [System 1].
3. Select [Initialization].
4. Select [Counter Data].
5. Select [Fixing Counter].
6. Press the Start button.
7. Exit the Service Mode.

USE A OEM cart. not third party

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Install was done incorrectly,

CAUSE: Initial settings did not take when programmed.

SOLUTION: Time and date, telephone and ADF serial numbers need to be reentered:

1. Sub-power ON g Utility/Counter g Machine Admin settings g System settings g Date and time setting g (Enter year/month/day/time) g OK g Exit g Power OFF sub-power switch.

2. Enter Service Mode g System settings g Setup date input g (Enter year/month/day) g OK.

CAUTION: DO NOT POWER OFF. Leave machine in Service Mode.

3. In the Service Mode g System settings g Telephone setting g (Enter 16-digit number) g OK. Repeat for the fax number. Set to all 9s if there is no fax number.

CAUTION: DO NOT POWER OFF. Leave machine in Service Mode.

4. In the Service Mode g System settings g M/C serial number setting g touch ADF g (Enter ADF serial number) g OK g Power OFF sub-switch.

5. Power ON sub-switch and run copies with no security lines.


Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Enter in the service mode and select counter mode and reset a counter to selected parts.

How to enter service mode on bizhub 164 + bizhub 215

NOTE
• When Main-power was turned ON while the Serial No. was not entered (including
initial status), the message to require entering the Serial No. will be displayed.
Make sure to enter the Serial No. at setup. sound like some did not follow the set procedure. go to service mode and enter the machine serial make a mistake machine will be out of commission

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

c-2557= ATDC Sensor abnormality to reset go to service mode, to enter service mode perform these steps, 1-press utility/counter button from the panel, 2-press check details, and press "STOP" 0,0, STOP 0,1 3-now you are in service mode, 4-click on tech rep mode,or Adjustment 5-now click on "Printer" 6-here increase the value, suppose you have 150, make it 170, press the clear button to clear it and enter new value which should be more than the previous one. press enter and exit from the service mode.

Administrator pw is "000000000"
Service pw is Utillity + counter + "stop" 0 0 "stop" 0 1
stop 9 mode 1

I’m happy to help further over the phone at https://www.6ya.com/expert/mustafa_06f84c65ab5cc745