My SAMSUNG washing machine model WA10F4 won't open water inlet. Please advice on what to do..need it badly. Kindly suggest where to bring for repair.

Most washers will have the service technician guide/wiring diagram information in an envelope attached somewhere inside the machine .... generally behind a panel that is not too hard to remove so the service technician can get to it easily. I am not familiar with your machine so I can not suggest which panel to remove to see if the information is there.

I have a link for the manual: https://read-download-books.com/v6/preview/?pid=6&offer_id=355&ref_id=b9167b56d8e059b95b231f9405b2ef5K_d95bfa30_c28f910b&sub1=d95bfa30&keyword=Samsung_Automatic_Washing_Machine_Wa10f4_Manual.pdf&sub8=Samsung_Automatic_Washing_Machine_Wa10f4_Manual.pdf&m=Samsung_Automatic_Washing_Machine_Wa10f4_Manual.pdf

Good luck with your troubleshooting...

Here's a few instruction's How to Diagnose Washing Machine Problems

Step 1:
If the washer won't start, check the power cord or reset the circuit breaker depending on the issue. It may be overheated and shut off temporarily. Let it cool for 30 minutes, and if it still won't start, call a professional.

Step 2:
If the motor transmission failed or the drive belt has broken, these need the assistance of a professional.

Step 3:
If the washer won't drain, clean out the drain hose and straighten any kinks. If the drain hose fits too tightly in the standpipe, adjust it to allow for a minimum of 1.25 inches for airflow so water can drain.

Step 4:
If the washer won't fill or fills slowly, turn the faucet handles counterclockwise as far as possible. This is usually the result of partially open faucets.

Step 5:
Call a profession if the washer overfills. This means the water-inlet valve or switch is defective.


Kindly regards,
-micromaster
micro & yakman unltd.

Samsung WA13G7Q1 NOT LOADING WATER

Hi,
you will need to replace the main pcb to fix it. I'll attach a video on how to do it. You should be able to get the part cheap online. Umina Beach Appliance Repair

Sounds as if the internal water valve may be stuck in the open position, try replacing the valve

If the water stops when you stop the cycle, then the pressure sensor is at fault. If you need to turn the water supply off to stop it, then the water inlet valve is at fault.

It ispossible that the machine does not start off the cycle because there are errorsdue to feedback from the inputs. For the program to start up the main programcontroller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting fromthe flow of water into the drum as also the drain valve to open to exit thewater at the point of the program cycle. If this does not happen then thevoltage at the valve/motor/pump must be checked or the fault relates to novoltage from the controller. This meansthe controller is a suspect.If thewater flows then the flow should be good, if not the inlet valve is bad orthere is dirt in the filter. Also check the flow at the inlet of the waterline. Once the water comes into the system the WATER LEVEL SENSOR - normally apressure switch- must activate at the preset/chosen level to give the signal tothe program controller to switch on the motor. What is most important for themotor to start functioning is that the door switch must be ON when the door isshut or this will be an error for starting the motor for rinse and wash.Check thislink to replace the inlet valve:http://www.espares.co.uk/advice/washing-machines/a/7/1408/how-to-replace-the-inlet-valve-on-a-washer-dr.html

It is possible that the machine does not start off the cycle because there are errors due to feedback from the inputs. For the program to start up the main program controller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting from the flow of water into the drum as also the drain valve to open to exit the water at the point of the program cycle. If this does not happen then the voltage at the valve/motor/pump must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

If the water flows then the flow should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Check this link to replace the inlet valve:

http://www.espares.co.uk/advice/washing-machines/a/7/1408/how-to-replace-the-inlet-valve-on-a-washer-dr.html

Finally after the wash the drain valve will be activated, the water is allowed to come in to rinse and then finally the dry spin with the drain valve/pump activated so as to drain off all the water from the clothes during the spin.

Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pump.

Please check the link below:

http://www.repairclinic.com/Washing-Machine-Troubleshooting?red=Washing-Machine-Repair-Help

I NEED TO KNOW WHAT SHOULD I DO WITH MY SAMSUNG 8.0KG WA10F4 DIAMOND DRUM IF THE WATER FROM THE TUB IS NOT DRAINING..AS IF THERE'S SOMETHING STOPING THE WATER TO FLOW