I do want to have an paper sheet holder for my pixma mp 150

Sir,
when your printer is not recognized paper or paper tray is blank.Then it show E2.Paper tray switch is not on or switch is not work.Please clean it soft brush.Reload the paper correctly and press black or color.

Hi there,

Error E2.
Action : Reload the paper correctly and press [Black] or [Color].

Loading Paper
Follow this procedure:
1) Open the Paper Support, then pull out the Paper Support Extension.
2) Place a stack of paper (print side up) in the Auto Sheet Feeder, pinch the Paper Guide and adjust it to the left side of the stack.
- Set the Paper Thickness Lever to the correct position for the paper.
Important : Make sure the stack does not exceed the Load Limit Mark.

Hope this helps.
Have a good day.

Hi there,

Loading Paper into your Canon MP 160 Pixma.

A) Loading Paper :
Follow this procedure:
1) Open the Paper Support, then pull out the Paper Support Extension.

2) Place a stack of paper (print side up) in the Auto Sheet Feeder, pinch the Paper Guide and adjust it to the left side of the stack.
* Set the Paper ThicknessLever to the correct position for the paper.
Note : Set the Lever to the left for most paper. When the Lever is set to the right, the confirmation message appears before the machine starts printing.
Important : Make sure the stack does not exceed the Load Limit Mark.


B) Loading Envelopes
Follow the following steps:
1) Open the Paper Support, then pull out the Paper Support Extension.

2) Prepare the envelopes for loading.
Important : * Press down firmly on the edges of the envelopes to make the folds crisp. Also, press firmly on the area that corresponds to the edges of the back flap.
* Remove any curling by holding the edges diagonally and bending them gently.
* If the edges of the envelopes are inflated or curled, place the envelope on a flat surface. With a pen, press down while moving it from the center toward the edges of the envelope.
* Ensure that no curl or puff exceeds 1/8 in. (3mm).

3) Place the stack of envelopes (print side up) in the Auto Sheet Feeder, pinch the Paper Guide and adjust it to the left side of the stack.
* Load the envelopes in the Auto Sheet Feeder with the short side down.
* Set the Paper Thickness Lever to the right.

Important : Make sure that the stack does not exceed the Load Limit Mark.

Hope this helps. PLease rate my response.
Thanks
Have a good day.

no both are different
Here are the list of cartridges u can use
MP210
PG-30 Pigment Black
PG-30 Pigment Black Ink Cartridge
PG-40 BLACK
CL-31 Color FINE Ink Cartridge
CL-41 Color
MP240
PG-210 Black Cartridge
CL-211XL Color Cartridge
CL-211 Color Cartridge
PG-210 XL Black Cartridge

I have had a MP 150 Cannon Printer with a E3 paper jam code..when NO visable paper jam is present ! Your No paper problem may be as a result of similar issue due to a small piece of paper stuck in the roller assembly out of sight. TRY this, Turn printer off wait (10 seconds) or more then turn printer back ON and listen for roller assembly to turn the ROLLERS and then FORCE FEED
a sheet of paper into rollers until it PULLS paper through and SEE if any scrap of paper comes out with the sheet !! If this works you should see that it clears the code. and resets your printer.
Let me know if this works. Phil at [email protected]

GOOD LUCK !

Sure. Take paper towels and clean out, absorb the excess ink for the tray.
http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=SupportDetailTabAct&fcategoryid=238&modelid=12764

E3 error on the MP150 is a paper jam error. Make sure that there is nothing obstructing the paper going into the printer and that the feed mechanism doesn't have anyhting in it. Also run a roller cleaning from the printer software.

To download the driver for Canon Pixma MP 150, please click the following link:

Canon Pixma MP150 driver for Windows XP/ Vista

Thank You

This is definitely a mechanical problem. You might want to at least partially take the printer appart and inspect it very thoroughly if you haven't done so yet. Did you have any paper jams before? Sometimes when you remove a paper jam the sheet rips and you end up with some shreds of paper lodged in the printer mechanism causing more jams. Another possibility might be cracked or bent paper guides, or simply dirty rollers (these you can clean with alcohol).

i have a canon pixma mp 500 and a new computer misplace my disc and can install