Question about Konica Minolta Bizhub C552 Copier

1 Answer

ERROR CODE C3B02 KONICA MINOLTA C552

ERROR CODE C3B02

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Konica Minolta Master
  • 6,850 Answers

Have you changed the fusing unit? If try that first, then relace the IH Power supply or the (coil unit) is what the fuser attaches to when you install one. power supply is located right side under the control panel, .

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Posted on Nov 14, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
hamzaskilltd
  • 318 Answers

SOURCE: Solution for error code c2557 konica minolta bizhub 250 machine

ADTC sensor failure

Posted on Aug 07, 2010

  • 2 Answers

SOURCE: konica minolta bizhub 350

• The Fusing Roller Sub Thermistor does not
detect the required temperature within 30 sec.
after a warm-up cycle has begun; therefore, the
copier does not complete the warm-up cycle.
• The temperature of the Fusing Rollers does not
reach the required level even after the set period
of time has elapsed during a warm-up cycle.
1
Check that the H1[ fuser lamp] comes on when the Main Power
Switch is set to ON, and correct or replace as necessary.
- -
2
Check that the H2 comes on when the Main Power
Switch is set to ON, and correct or replace as necessary.
- -
3
Check the installation of the TH1 and the TH2, and
correct or clean as necessary.
- -
4
Check the operation of the TH1.
Remove CN80 (4P), and then check that the resistance
across CN80-2 and -3 on the Thermistor is
infinity.
- -
5
Check the operation of the TH2.
Remove CN81 (4P), and then check that the resistance
across CN81-2 and -3 on the Thermistor is
infinity.
- -
6
Check the continuity of the H1.
Correct or replace as necessary.
- -
7
Check the continuity of the H2.
Correct or replace as necessary.
- -
8 Change PU1 - -
9 Change PWB-A

Posted on Nov 19, 2007

oranous_comp
  • 1 Answer

SOURCE: proplem with KONICA MINOLTA bizhub C450

c-3451

Posted on Nov 10, 2008

SOURCE: IError Code C13FO on konica minolta Di1610

C13F0 - Laser error
The laser output exceeds the upper limit value.
The laser output remains lower than the lower limit value.

Posted on Aug 23, 2009

  • 1 Answer

SOURCE: Konica Minolta Magicolor 4690MF gives 0502 error.

machine trouble 0092 service call
This happen after I cleaned the waste box for Konica Minolta Magicolor 1600W

Posted on Mar 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Konica Minolta C552 wrong image unit caused C-CD10 Error, changed boards, disconnected hard drive, reformatted hard drive, updated firmware. Took out fuser still gets code. Hytec doesn't know.


The Hard Drive is not formatted. First, get in service mode, State confirm, HDD ADJ, HDD Format. Run Physical first, about two hours then logical a few minutes . Does the machine know it has one, Installed/Uninstalled in service mode. Then replace.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Mar 02, 2017 | Konica Minolta Office Equipment & Supplies

1 Answer

C3B02 code konica minolta 452


Do this procedure once if the code comes back do NOT RESET again because you are dealing with the fuser which can catch on fire ruining a perfectly good day!!! Have the Fuser replace or the coil, or Fuser High Current Power supply.

1.
Turn OFF the main power switch.
2. Turn main power switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

May 26, 2016 | Konica Minolta Office Equipment & Supplies

1 Answer

I have konica minolta c552 has an error C3b02


Hey jrf, the manual says to check, in this order; proper fuser installation, proper closure ( door latch ) of the right hand door, check around-all around-for wiring connection issues, change fuser, then coil, then IHPU, then PRCB, then REDB. If you have a trade-in, or lease return, at the shop; it might pay to do some parts borrowing.

Sep 23, 2015 | Konica Minolta Bizhub C552 Copier

2 Answers

Konica Minolta C552 error code C-B02


Replace the IH Power supply, it will solve your problem... Page 71 Item 5 from the parts manual.

Jul 17, 2015 | Konica Minolta Bizhub C552 Copier

1 Answer

Error code C3B02


Turn off the machine using main power switch not the one on the control panel. But make sure the on the control panel switch is on. Now hold down the utility/counter button and turn the main power switch on hold down to you see trouble reset touch it power off WAIT TEN SECONDS power on if code comes back DO NOT RESET it means the Fuser Electro-magnetic current amp and or coil is bad reset again it may catch on fire ruining a perfectly good day!!! Get a tech out to look at it

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Jul 10, 2014 | Konica Minolta Bizhub C452 Copier

1 Answer

Bizhub c552 error c3b02


In all likelihood this is the IH power supply board. Not a difficult procedure but the board may be expensive. Can send through details if required.Cheers

Jul 06, 2014 | Konica Minolta Computers & Internet

1 Answer

What is bizhub C552 p-14 error?


p codes are warnings that a consumable is reaching the end of its life you can go into service mode and it will give you a list of error codes including p codes

Jul 04, 2014 | Konica Minolta bizhub C552 Waste Toner Box...

1 Answer

Minolta bizhub C552 code c3102


replace the fusing unit

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Apr 26, 2014 | Konica Minolta Minolta Bizhub C353 Copier

1 Answer

What does Error Code C2564 Konica Minolta Bizhub 552 mean


Black drum ATDC replace the black developer unit, also check to make sure the black toner is getting into the black developer unit. Open close the front door to reset the code (Not the Toner door)

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Apr 24, 2012 | Konica Minolta Bizhub C552 Copier

Not finding what you are looking for?
Konica Minolta Bizhub C552 Copier Logo

Related Topics:

1,256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6850 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

George Mclaughlin

Level 2 Expert

364 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...