How to solve error c0650 on minolta di2510

Question edited for a lot more clarity and add maker.
Question moved to maker category.

Cooling Fan failure.

Konica-Minolta Di2510 - Error Code

Printcopy.info https://printcopy.info > model=Di2510 > code=C0045
Code: C0045; Description: Cooling Fan Failure • The Cooling Fan Motor Lock signal remains set to H for a set period of time while the Cooling Fan Motor is ...

Missing: dialta ‎' Show results with: dialta

Error Codes > Konica-Minolta > Di2510 > page 1

Printcopy.info https://printcopy.info > model=Di2510
Code: C0045 · Description: Cooling Fan Failure The Cooling Fan Motor Lock signal remains set to H for a set period of time while the Cooling Fan Motor is ...

Error code C0650 Konica Minolta bizhub 160 Black
Faulty scanner home
position sensor.
• The scanner home position sensor (PS100) does not go
from HIGH to LOW when the scanner motor (M4) is energized
for a given number of steps after the sequence to
bring the scanner back to its home position has been
started at the end of a scan motion and during re-shading.
• The scanner home position sensor (PS100) does not go
from LOW to HIGH when the scanner motor (M4) is energized
for a given number of steps after a scan motion has
been started at the end of a PS100 home check scan
motion and during re-shading.
THANK'S

Is 2 home sensors.Try reset the code.

C0650 code is the scanner lamp home sensor is not working so the copier does not know where the scanner is clean first will require removal of the orginal glass (large one) the other code is the image unit, has it been replaced or repaired recently. To fix mite require a new image unit

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

bizhub 211 error code C0F32, To solve this code simply replace the developer of the machine.

Hello sir; This problem caused by home positon senser problem, replace it.

ARE YOU CONNECTED TO A LAN CARD OR NETWORK OF ANYKIND.

GO ON LINE AND TYPE IN

MINOLTA DI2510 B/W COPIER C-0500 ERROR MESSAGE
ENTER

ROD

C0650: Faulty PC12 C0651: Faulty PC13
Relevant Electrical Parts Scanner Home Position Sensor 1 PC12 Scanner Home Position Sensor 2 PC13 Scanner Motor M5 Master Board PWB-A BCR Board BCR HGB Board HGB MFB Board UN2

C0650 .THIS CODE IS FOR SCAN MOTOR OR SCAN SENSOR PRBLEM.JUST CLEAN SENSOR OR CHECK SCAN MOTOR IN OPTICAL UNIT.MAY BE MOTOR HAS PROBLEM.BY MIAN JEE

This is a scanner problem, try the following...



C0650, C0660
Step Check Item Result Action
1 Scanner can be moved manually.
NO Correct drive coupling (Scanner
Belt tension, pulley operation,
drive cable tension)

2 Scan motion: initial scan motion after the
Power Switch has been turned ON or Front
Door has been opened and closed.
NO Carry out misfeed/malfunction
troubleshooting procedures.

3 Connectors are connected properly on
Scanner Motor Drive Board: PWB-IC
PJ1IC, PJ2IC, and PJ3IC.
NO Check connectors for connection.

4 Scanner Motor turns when the Start key is
pressed.
NO Check connectors for connection.
Change motor. Change
Scanner Motor Drive Board.

5 I/O check for Scanner Home Sensor: the
voltage across PJ6C-2 on Image Processing
Board and GND is DC 0 V (home position)
when the sensor is blocked and DC 5
V when the sensor is unblocked.

YES Change Image Processing
Board.

NO Check sensor for installation.
Correct detecting plate.
Check sensor connector for
connection. Change sensor.

6 “IR Area” check:
Malfunction when Power Switch is turned
ON after “Top Image” has been set to 0 and
“FD-Mag.” to 1.000.