What are correct settings - Whirlpool Cabrio WTW6600SBT Top Load Washer

Press and hold CLOCK until the message window displays C, and the default day is announced.
To change the day setting, press MEMO/REPEAT or ANNC/SKIP until the correct day is announced.
Press CLOCK. The current hour setting is announced. The correct day setting is saved.
To change the hour setting, press MEMO/REPEAT or ANNC/SKIP until the correct hour is announced.
Press CLOCK. The current minute setting is announced. The correct hour setting is saved.
To change the minute setting, press MEMO/REPEAT or ANNC/SKIP until the correct minute is announced.
Press CLOCK. The current year setting is announced. The correct minute setting is saved.
To change the year setting, press MEMO/REPEAT or ANNC/SKIP until the correct year is announced.
Press CLOCK. The new day, time and year are saved. The correct year setting is saved.

To check the clock, press CLOCK.

The above is from page 5 of the manual at
http://att.vtp-media.com/ecp/documents/product_Product/223/UserManual/944/1739_manual.pt2_i6.pdf

The time and date is set at the base unit.
Press the TIME/SET button
Press the TIME/SET button again
Press the CHANGE button until the correct day is announced
Press the TIME/SET button
Press the CHANGE button until the correct hour is announced
Press the TIME/SET button
Press the CHANGE button until the correct minute is announced
Press the TIME/SET button
Press the CHANGE button until the correct year is announced
Press the TIME/SET button to finish and the current clock setting will be announced

You can hold the CHANGE button down when setting the minutes or year to increment in steps of 10. Following is a link where you can download the manual.
http://att.vtp-media.com/ecp/documents/product_Product/614/UserManual/2041/e5655_manual_bkm.pdf

Press the SET button until the month if flashing. Then press the CH button until the correct month is showing. Press SET again so that the day is flashing. Press CH button until correct day is showing. Press SET so that the year is flashing. Press CH button until correct year is showing. Press SET until nothing is flashing. You should be done.

manual is online here
http://www.fixya.com/support/p84926-southwestern_bell_fa_970_digital/manual-17765

Owners manual: 3-10:

Setting the Clock for Systems with HR and
MN Buttons
Press and hold HR until the correct hour appears on the
display. Press and hold MN until the correct minute
appears on the display. To display the clock with the
ignition off, press RECALL or HR/MN and the time
will be displayed for a few seconds. There is an initial
two-second delay before the clock goes into the
time-set mode.

Setting the Clock for Systems with
SET Button
Press SET. Within five seconds, press and hold the
SEEK right arrow until the correct minute appears on
the display. Press and hold the SEEK left arrow until the
correct hour appears on the display.

what service provider are you using, I can provide you with the proper set up instructions.You must set up the phone to talk to the celluar service you are using example TMOBILE- ATT after I know that I can help More.
The most common cause is that the Data account for the GPRS data profile you are trying to use was never
configured, is configured incorrectly, or the proper GPRS profile was just never "Activated" under the WAP settings after the profile was
created. First go into the Data account services under the GPRS settings & make sure you have set up the correct profile for your
carrier. If it is set up, then edit the profile & make sure all the settings are correct as well as the spelling is correct. Then go into the
WAP Service settings & check to see that you have selected the correct SIM & correct profile, as well as Activated the profile. To
Activate the profile just select the correct profile from the list, and tap on the Activate profile bar. Also edit the profile to make sure
all the settings are exactly correct for your carrier, as well as the correct Data account (GPRS account) was selected for the internet.

Set the clock
You must set the clock so that the system announces the correct day and time with any incoming messages. After this, if you subscribe to the caller ID service, the system will update the clock eac h time new call information is received. Press PLAY/STOP to exit at anytime while setting the clock.

1. Press and hold CLOCK until the message window displays C and the default day is announced.
2. To change the day setting, press
MEMO/REPEAT or ANNC/SKIP until the correct day is announced.
3. Press CLOCK. The current hour setting is announced. The correct day setting is saved.
4. To change the hour setting, press
MEMO/REPEAT or ANNC/SKIP until the correct hour is announced.
5. Press CLOCK. The current minute setting is announced. The correct hour setting is saved.
6. To change the minute setting, press
MEMO/REPEAT or ANNC/SKIP until the correct minute setting is announced.
7. Press CLOCK. The cu rrent year is announced. The correct minute setting is saved.
8. To change the year setting, press
MEMO/REPEAT or ANNC/SKIP until the corr ect year is announced.
9. Press and release CLOCK. The new day, time and year are announced. The correct year setting is saved.
To check the clock, press CLOCK.

change it through your gps
where you set favourites or home
it obviously did'nt set your correct settings through the map
make sure home settings on system itself are correct such as country city etc

Program the Date & Time and Print Method using the 3 buttons: Mode, Select, Setting:
Date & Time: Press the Mode button. The Hour will start blinking. Press the Setting button
until the correct hour is displayed. Press Select to set the hour shown.
The Minutes will blink. Press Setting until the correct minutes are displayed. Press Select
to set the minutes shown.
The Seconds will blink. To set the seconds at 00, press the Setting button. Press Select.
The Year will blink. Press the Setting button until the desired year is shown. Press Select
to set the year shown.
The Month will blink. Press Setting until the correct month is shown. Press Select to set
the month shown.
The Day blinks. Press Setting until the correct day is shown. Press Select to set the day
shown.