I have usuing L210 red led blink on ink indicator and on paper indicator any solution

Epson printer blinks both red and green lights, which means the paper gets jammed in your Epson printer. You can fix the issue using the steps:

·Check printer ink cartridge
·Check the printer print head and fuser
·Fix the paper jammed

Follow the steps to fix Epson printer lights blinking error.

This is general error of the printer. When you have to change the new mother board you should be initialized it then it can be ready mode. When you try to initialization you need printer printer adjustment program. You can batter find out from google & write down EPSON Stylus R230 Printer Adjustment program or ink reseat program.

epson R230 2 red light start
Printer status Fatal ERROR
LED indicator
power: OFFpaper: FAST BlinkInk: FAST Blink
Carriage Unit cannot move correctlyMotor cannot rotate correctly
Note: CDR (CD/DVD) guide assembly is not close properly will also occurs error or blinking the paper indicator and ink indicator.
For easy to me to understand.Please check the light indicator, either blinking simultaneously?

There is no error 5100 in the manual so look at the following:

(1) Operator call errors (by LED blinking in orange)

LED blinking in orange. Error Solution Remarks

2 times No paper. Set paper, and press the Resume/Cancel button.

3 times Paper jam. Remove the jammed paper, and pressthe Resume/Cancel button.

4 times No ink. Replace the empty ink tank(s). (Pressing the Resume/Cancel button will exit the error without ink tank replacement.)

5 times The print head is not installed properly. - Install the print head, and close the

front cover.- With the print head installed, turn theprinter off and on.

- Re-install the print head.

8 times Warning: The waste ink absorber is almost full (approx. 95% of the

maximum capacity). Pressing the Resume/Cancel buttonwill exit the error, and enable printing.

In repair servicing, replace the bottom case unit (QM2-0647), or 5-item set of

the ink absorbers

(QA4-1012/1013/1014/1015/1055).

The service call error, indicating the waste ink absorber is full, is likely to occur soon.

9 times The connected digital camera or digital video camera does not support

Camera Direct Printing.

After removing the cable between the camera and the printer, press the Resume/Cancel button, and re-connect the cable.

(2) Service call errors (by LED blinking alternately in orange and green, or lit in

orangeLED alternate blinking in orange and green

Error Solution

(Replacement of listed parts, which are likely to be faulty)

2 times Carriage error - Carriage unit (QM2-0655 / QM2-0831)

- Timing **** strip film (QA4-1053)

- Logic board ***'y (QM2-0750 / QM2-0751)

- Carriage motor (QK1-0175)

3 times Paper feed error - Timing sensor unit (QG4-0277)

- Timing **** disk film (QC1-2781)

- Feed roller ***'y (QF4-0155)

- Platen unit (QM2-0650 / QM2-0828)

- Logic board ***'y (QM2-0750 / QM2-0751)

- Paper feed motor (QK1-0224)

4 times Purging error - Purge unit (QM2-0825)

- Logic board ***'y (QM2-0750 / QM2-0751)

6 times Internal temperature error - Logic board ***'y (QM2-0750 / QM2-0751)

7 times Waste ink absorber full - Ink absorber (QA4-1012 / 1013 / 1014 / 1015 / 1055)

- Bottom case unit (QM2-0647)

8 times Print head temperature rise - Print head (QY6-0042)

- Logic board ***'y (QM2-0750 / QM2-0751)

9 times EEPROM error - Logic board ***'y (QM2-0750 / QM2-0751)

13 times USB Host VBUS overcurrent - Logic board ***'y (QM2-0750 / QM2-0751)

- DCD board ***'y (QM2-0825)

15 times Other hardware error - Logic board ***'y (QM2-0750 / QM2-0751)

Continuous alternate blinking

Flash ROM error - Logic board ***'y (QM2-0750 / QM2-0751)

Lights in orange

RAM error - Logic board ***'y (QM2-0750 / QM2-0751)

*

Hop you can understand the above as it is straight out of the service manual.

Good luck

red paper light is blinked as it is indication that plz insert paper in your printer, and ink light blinks because your printer is low on ink, kindly get your printer cartage refilled.

my epson stylus photo R230 Printer problems always
two red light blinking
please help me
thank you

could someone show us how to open the r230? im having hard time cleaning the waste ink pad because i cannot open the r230..

ok...start by removing the drivers from control panel, go to website and get new drivers, install them, try it again.

http://tinyurl.com/6qcpgy

I just today threw away my R220. If your 2 red lights are going and the power light is off, then your printer has died. It just happened to me. It sucks, but there is no way to fix it.

Hi Greenhorn, Your info is slightly conflicting - I think. As I remember the C60 has just 2 LED's: 1 - Green for Power 2 - Red for Error The third button - Cartridge exchange - has no LED Now it is a while since I looked at a C60 and my brain leaks like a sieve, but that's the way I remember it and feel free to correct me if I'm wrong. The error codes I remember are: Printer status - Indicators - Priority Power - Error Power ON condition On - Ink sequence Blink - Ink Cartridge change mode Blink - Data processing Blink - Paper Out *1 - On Paper jam condition *1 - On Ink end (Black) *1 - On -> Blink Ink level low (Black) - Blink-> Blink Ink end (Color) *1 - On -> Blink2 Ink level low (Color) - Blink-> Blink2 Ink end (Black and Color) - On -> On No Ink Cartridge (Black or Color) *1 - On Maintenance request (Ink Overflow Countererror) *1 Alt Blink Alt Blink Fatal error *1 Off On Special setting Blink2 Blink2