My printer Konica Minolta stopped working and showed me an error code F-26-6

If the red light is blinking on your Konica Bizhub 423, it usually indicates an error or issue with the printer. Here are a few things you can try to resolve the issue:

1. Check the display panel: The display panel on the printer should show an error message or code indicating what the issue is. Check the manual or contact Konica Minolta support to find out what the error code means.
2. Restart the printer: Try turning off the printer, unplugging it from the power source, waiting for a minute or so, and then plugging it back in and turning it on.
3. Check the toner: If the toner is low or empty, the printer may not function properly. Check the toner levels and replace the toner cartridge if necessary.
4. Check for paper jams: Paper jams can cause the printer to stop working. Check the printer for any stuck paper and remove it carefully.

If none of the above steps work, you may need to contact Konica Minolta support for further assistance.

Konica C224 error C0206 & C0208 - Copytechnet

www.copytechnet.com > ... > Konica Minolta

Jun. 26, 2017 - Hi all I have the C0206 & C0208 when connecting the PC-410 (twin cassette) ... jonbonse is offline ... Konica C224 error C0206 & C0208 ...

Error Codes > Konica-Minolta > bizhub 350 > Code C0208

printcopy.info > code=C0208

Code: C0208; Description: Tray 4 Elevator Failure - The Lift-Up Sensor is not unblocked even after the set period of time has elapsed after the paper lift up ... Missing: Mita. ‎' Must include: Mita.

Konica bizhub error codes - Largest PDF Library

cs3.cargosimply.com > konica-bizhub-error-codes
konica minolta bizhub c35 error codes a complete list of error codes with a ... copier what does this code mean reply delete, code c0208 description tray4 lift up ... toners konica minolta toner kyocera mita toner lexmark compatible ink price c 16 ...

2451 replace the cyan (Blue ) Image unit

3423 replace the fuser unit


3334 No such code

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Basically -no. If you could get a reset chip for it, you could probably carry on using the original drum for some time. For example http://www.tonerstop.com.au/konica-minolta-bizhub-c353-bundled-set-of-4-compatible-drum-chips

Yes I stated what I recommended to do in your last post!

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Remove the drum cartridge, then remove developer unit, then the charge housing above the drum the remove the drum do not touch it has to be done from the side of drum. once removed then is sensor that has a white cover on it, there is also a clear one white one is in the rear on the left side clean DO NOT USE A VACUUM Cleaner the static electricity will destroy the sensor. Then re install. run all required check . Unless you know what you are doing get a qualified Konica Minolta Technician Has to have Konica Experience You have a legacy Konica machine

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

ADTC sensor failure

Error 08 relates to the main motor having problems turning. Quite often this is caused by a faulty consumable (opc,toner or transfer belt). Could also be that the lid is not closing properly and stopping the toner carousel turning freely.

F26 Toner density adjustment problem. This means machine is undertoned. To repair, replace developer and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some feel that you should disconnect the toner motor first. This ??? ?????? happens probably because either machine wasn't set up properly, or the customer kept on using the machine with the toner light on.