My 42" Plasma TV has always been plugged on the outlet. Today, I found there was no red light on the TV. I tried to unplug and re-plug, there was no power come to the TV set. I don't see there is any place for fuse replacement or other opening that I can check. Any suggestions?
You have burned an internal fuse on the main power board. There are 2 right next to where the main power line plugs in ( after the noise filter ). Yes, you will have to unscrew the rear plate to get to it ( about 24 screws ). You just follow where the lead goes from the plug - you will see where the fuses are - right next to where the plug mounts to the power board. To check this set your meter to ohms and check for continuity - odds are one of the two fuses is done. THIS IS A PANASONIC SPECIFIC FUSE - it cannot be replaced with one that looks like it or fits the same slot. This fuse is a time-delay slow burn fuse and replacing it with anything other than the correct type will cause more damage and possibly total the unit. The panasonic part number is K5D802BNA005 and is available from several parts retailers - just google "panasonic part K5D802BNA005" and many reputable firms will come back on the search. They cost approx. $1.95 US ( so the shipping is probably 7.00 more ) Hope this helps and be careful of the internals and static electricity from your body.
If you have blinking lights or no lights or steady red light this is a power problem the best solution is to get a service manual for your set and find the symtoms and there is usually a trobleshooting guide for the repair in the service manual a steady red light means the p a board needs to be checked or replaced blinking lights can mean a fuse is blown or a board may be bad no lights may mean bad connection bad power unit or fuse before you start guesing or calling expensive repair company do your research find a service manual and if you really can handle this fix then you can get a used non working tv and switch out the parts with out spending a fortune..most people break the screens so theres plenty of lcd's being sold as is for parts try ebay or craigslist ..
hope this helps
The fuse is located on the inside of the tv. you have to remove the the rear panel as if repairing.
The solution is, DONT BUY PANASONIC PRODUCTS!
Amen, brother.
×
The standby button wont go off the tv wont go on 42inch sanyo ce42fd90 b
If its not the internal fuse need new power supply bourd send me modal number and i will see if ive got one in my spare parts
There is a few things that can be done. I have this same issue, and i braved the 40 screws and took it appart.I have another posting that shows photo's check it out so far http://www.fixya.com/support/t566714-akai_plasma_tv_5_blinking_red_lights
I found a great power supply kit at tvrepairkits. com. This kit is loaded with a wide range of caps which covers several brand and model TVs. This kit also comes with instructions which helped me a ton...hope this helps.
Http://www.fixya.com/support/t566714-akai_plasma_tv_5_blinking_red_lights
A blown internal fuse would cause things to appear completely dead. It is not intended to be user serviced. If you do find a blown fuse, never replace it with a larger size. Using an oversized fuse may cause additional damage. If the same size blows again there is some sort of fault, typically something like a shorted diode, electrolytic capacitor, or switching transistor.
There could be more than one fuse. Sometimes there is one on the AC power coming in, and one or more on various outputs from the main power supply. The AC line fuse may fail simply from a nasty surge coming down the power line. Other fuses usually blow from internal faults.
The main page for this site suggests there are service manuals here. I haven't seen any. They'd be very helpful to someone like me that understands electronics. They're generally beyond what end-users can understand.
JoeJoe206, your problem sounds the same as what just happened to my FWD-42PV1, which was 2 months past its warranty. When i plug it in, the green light goes on and i get clicking every few seconds for about 15 seconds, then it gives up and just goes to red. The picture never comes on. There was a pretty detailed diag manual i found online that indicated that it is most likely the A board or the G board (the power board) but the troubleshooting section looked translated from Japanese. Both A and G boards are pricey boards ($400/$550). If you find anything interesting, drop me a line at markahlady -at- yahoo.
I have the exact same problem. when i took it to the repair shop it came on and he stated that it was on the wrong input. so i took it home plugged it in and watched it ffor a couple hours that night. the next morning it turned on for about half a minute then it shut off and never turned back on again. what should I do?
Sounds like a power supply issue.
My 52" jvc flat screen projectory tv powers on for a few seconds then before shuting off on its own it makes a clicking sound, and it wont stay on, I have unplugged it for a while then plugged it in but its still shutting off on its own, what might be the problem and how can i fix it?
Have a LG 720 plasma Tv the red light does not come on when plug in only the
blue light come on when i push in the button only.
I have a samsung and its a 42" flat screen tv it clicks for about 4 mins then turns on is my fuse going out if so how much would it be to fix it???
Try plug it somewhere else in the room or plug something that you know works in the outlet where the tv was plugged to make sure there is current
If you are under warranty and have a TV over 32", then they should come to you and repair it. Call the help line and they'll set it up. It could take a week for a local tech to make it.
Hi I have a Panasonic viera TV and I've changed the fuse in the plug and the fuse inside the TV and it still don't power on
Memorex MLTD2622 26 in. LCD TV TV/DVD Combo The Tv is on but picture. Wheni first turn on the tv, the memorex pops up then a black screen. what do you do I have checked all of the pluggs and connections and still no help.
Memorex MLTD2622 26 in. LCD TV TV/DVD Combo The Tv is on but picture. Wheni first turn on the tv, the memorex pops up then a black screen. what do you do I have checked all of the pluggs and connections and still no help.
×
Solution:
DO NOT BUY GATEWAY LCD TELEVISIONS.
China does not supply any service manuals to the usa. The technical department at GATEWAY do not have any manual are
very poor technition help.
I had the exact same problem and had to return the unit for repair. After examination I was told it was a power supply and they would fit a reconditioned (as they don't make new ones! ) for $750 AU.
Several visits to my home, the repairer, angry phone calls and about 10 weeks without a working TV and I got the unit back. The power works fine but after several weeks I am seeing white snow appearing on the screen !
Solution learn how to fix ur own ****
Check if one of the fan inside the tv is off if one is off you have to changed both
Where exactly is the fuse located? and is it hard to locate?
I can fix it easy as hell if u want 2 know how then call me 1847-507-2504
SOURCE: Plasma TV-power light does not come on
There are a couple of possibilities here. If the set is indead dead,
the most likely culprit is the "standby" transformer. If you are
getting a click followed shortly thereafter by another click, then the
TV is detecting a problem and shutting down to prevent further damage.
And if you get no clicks or anything at all, I would suggest you to look at
the fuse and the standby transformer. The standby transformer is a
small transformer that supplies 5V to the system even when off to allow
remote control. You need to see if the primary side of this
transformer is open or not. You should have 5V.
Goodluck,
Please don't forget to rate me as fixya..
35,709 views
Usually answered in minutes!
the red light comes on, but does not turn to green
have the same problem, only my tv is the european model 32U2000...
if i open the back, will i see an obvious fuse box, or ?????
hi.
i have basically the same problem, except my sony hdtv is the european model 32U2000. I also get a clicking noise...but no power light and obviously no power. could it be the fuse? if so, when i open the back will the fuse box be obviously there, or will i need to uncover something else first?
thanks.
s
I just bought a Sanyo CLT1554 LCD Television but to my surprise it would not power on what should I do. The AC power adapter is showing a green light but the TV is not showing any sign of power coming through.
My 42" Sony Plasma TV (PFM-42B2) was working properly and suddenly it stopped working. The red light comes on (changed itself to standby mode: like I turned it OFF). I tried to turn the unit ON and i can hear some clik like it's going to start,but it switched itself from Green ON to red light OFF. What could be the problem? Please help..
Thanks.
That is what I'm experienceing - no power to the TV. Yes, it's plugged in - but like the others no red light. It's just not coming on.
I have the same problem but after the fuse was replaced it blew as soon as it was plugged in. My Tv is an LG, 32LX1D.
MY DELL TV HAS A BLUE LIGHT AND NOW THE TV WONT POWER ON AND THE BLUE LIGHT ISNT EVEN ON MY SON PLUGGED HIS XBOX TO MY TV AND NOW NOTHING IS WORKING INCLUDING THE XBOX
I have a 42pd3000 & connection box for connecting other things like a dvd playstation etc ..it keeps switching off and goes on stand by clicking on and then off and now shows out of sync on screen.
42 inch Akai just stop working and power will not turn on.
my tatung 42 inches red light comes on but nothing shows
Have a Philips 23PF5320 LCD TV - it just died . the power light is off and there is no picture or sound
I was watching television and without any warning, my 2 1/2 yr old Akai plasma tv turned it self off and I can not get the tv to go back on.
power supply bad need to find new one
Please email me.
My 27" Plasma TV has always been plugged on the outlet. Today, I found there was no red light on the TV. I tried to unplug and re-plug, there was no power come to the TV set. I don't see there is any place for fuse replacement or other opening that I can check. Any suggestions? The TV shop said it was on the wrong input,but that is not the case becuase it will not even turn on.
When i put the tv on only the green light is come up and no power
AFTER REBOOT GREEN POWER LIGHT COMES ON, WHEN FRONT PANEL POWER BUTTON IS PUSHED ,LIGHT TURNS RED. NO PICTURE OR SOUND, NO OSD. MAIN POWER AND DIGITAL BOARDS HAVE BEEN REPLACED. EE-PROM SEEMS TO OPERATE, COULD NOT FIND ANY SHORTS ON SCAN BOARDS OR BY CABLE DISCONNECT?
My 42" Plasma TV has always been plugged on the outlet. Today, I found there was no red light on the TV. I tried to unplug and re-plug, there was no power come to the TV set. I don't see there is any place for fuse replacement or other opening that I can check. Any suggestions?
Absolutly no power to the TV. I have unplugged, checked circuit breaker, replugged and no power.
red or green light does not come on.
Have to control everything from the console since remote won't work without the red or green light being on.
Batteries in remote are fine.
When using either remote or panel button to power TV on, the red light goes green, you hear relays clicking and then within seconds, the light goes red and TV is in standby mode. Â Called NEC who gave info for local guys they recommend for repair; even after describing problem over phone, they said they could come to look at it for $175. Â They were here less than 10 minutes, tried to turn the TV on and confirmed what they had been told over the phone, and then diagnosed that it needs a new scan board and command board at a cost of $1300 plus! Â Don't waste your money like I did - just buy a new one. Â And I can guarantee I won't be buying another NEC ...
no power at after i unplug the set
no power when pug in tv
Plugged in and red light is on but appears to be flickering. Unable to turn on with remote control or on-off button on TV. No audio as well.
i have the same problem
I have a 42" Panasonic plasma TV. I tried to turn it on first using a remote control then manually. Nothing happens.
I can shut my tv off, but if I can back after like 8 Hours, it will no turn on, is an lcd hd polaroid tv. please help
My TV will not turn on there is a red light that keeps blinking on the front of the TV where the green light normally is when on
My 4242 works for about half an hour then it switch off and the power led starts to blink red: the manual say something about power stability... Any solution? Any news? Best regards.
changed the picture from stadium to zoom mode. played for a few minutes then screen went black, power lite blinked red and yellow, unpluged it pluged it back in and stand by lite comes on like its suppossed to, turn power on and power lite comes on green like its supposed to but still no pitcure. any ideas?
My TV will not turn on there is a red light that keeps blinking on the front of the TV where the green light normally is when on
I'm back. BAMOUT is my name. Does the DYLT32B have a fuse on the power supply? Thanks BAMOUT
T.V. power light does not come on i have no sound no picture
same here
50PB4D 50 in' .I have power to the TV as the red light is on but the green light doesn't activate so I have no picture or sound. I have tried switching off at the mains for 24 hrs and all the buttons on the TV and remote with no luck..Any Ideas?
o meu plasma Hitachi 42PD3000 TV Plasma 42 polegadas
acende a luz verde,passado alguns segundos muda para laranja,e o ecrä fica sempre escuro,como se estive-se desligado,o que podera ser?
my tv power light does not come on i have no sound no picture
power went and foung
no power to tv red light is not on. I have power to the receiver
my tv screen will not turn on i have change the fuse a number of times it turns on for a second then blows the fuse and turns of but i have power to my reciver
No power or lights. Fuse is not the problem have checked and it is good have voltage pass the fuse but then what??????
TV LIGHT DOES NOT COME ON SOO TV WILL NOT TURN ON .I CHECKED ALL OUTLETE AND PLUGS
I puchased the 42" plasma with ambianlight 18 months ago and the power went out. I called Philips but they have no solutions, except to send it to one of their approved service centers. What a nightmare!! It has been there for 2 weeks and no solution. I've been told by their service tech. that the entire "power pack" may need to be replaced and could cost $500 plus labor.
I am having the same problem. I am getting zero power on the T.V everything else plugged in to my surge protector has power. I have tried different outlet and that has not worked.
Same problem - no red or green light, no power. TV is absolutely dead and not even a year old! I tried calling Spectroniq help line and they have filed for bankruptcy. Any suggestions
My Hitachi 42PD7200 power led does not come on. No power at all. Tried other devices work find on the outlet. Tried a different power cable, change the fuse inside the tv but no luck
Help appreciated
power out of plasma tv
black screen" green light is on!! but picture will not come on, what could be the problem?
I have a 50' LG plasma and i have had it for about 7 months at the most and it decided to stop workin in the middle of watchin it..i have no power light(red or green) no sounds nothing its just dead..i would really like to to know what this problem is and why its doing this.
My Panasonic TH 50PX600U plasma power light just went out. the power would sometimes come back on .it would play for 2-5 mins and then power light goes out again sometimes for a whole day. I'm located in Trinidad West Indies and have no Panasonic Service Centers around so I went to my electronic technician ( fairly allright one too)and Kabam. After replacing 1 burnt capacitor and re soldering some cold solder on two boards...the TV is working new. I just thought I'd share this on the net to help others
[email protected]
i got a big screen tv i wanna by from my cousin for 20 bucks and gonna take it to the shop but the thing is that card has a shortage in and it want come on i just bought a toshiba from him that he thought didnt work 52 inch for 60 bucks and brought it home my husband went to hitting button taking it off regular tv which it was set on that and brought it to a house that had cable and the tv came on.. show perfect no problems yet my cousin thought it didnt work just wondering if i should take a chance with this other tv it doesnt come on after u plug it in no should no nothing and the card u plug into the wall it all batter taped up and all so someone help and give me some advice on what to do..
my 50 in samsung startes to make the mealody sound when i plug it in. it turns on and off . i am out of my money. really could use the help.
One year and 2 months.. i.e just enough to get past the free 1 year warrantly periosd...and I have the same problem. Now, a service guy in going to make a PAID house call.
Why the hell I bought a national tv? Crazy I guess.
I have a 32" Panasonic TV, I turned it on oneday and it blew the fuse in the back of the TV. I replaced the fuse andsee nothing else wrong. I switched outlets and it still blows.
i have a 32" polaroid lcd. today i unplugged it to switch cable boxes. when i plugged it back in nothing.. the little red light that means its even getting power isnt even on
when i turn on my toshiba plasma tv the blue stand by light wont come on but if when i press the power button it bleeps what can this be please?
i have a toshiba 32" plasma i went to turn it on but the blue standby light will not come on but there is power as i tried to press the on and off button all is does is makes a bleep does anyone have any idea of why this is please i was giving this tv from my nan who has sadly died and im heart broken thinking this no longer works
This is the best and interesting information you have shared. FL Studio 12 Serial Key
Hotspot Shield is a flexible web security and protection arrangement. Notwithstanding shielding you from hazardous online dangers, it likewise secures your protection and empowers you to get to any blocked sites and substance.
Hotspot Shield makes a virtual private system (VPN) between your gadget and its Internet door. This impervious passage forestalls snoopers, programmers, and ISP's from keeping an eye on your web perusing exercises, texts, downloads, charge card data or whatever else you send over the system.
Unblock any sites – Can't get to YouTube or Facebook at school or work? By utilizing Hotspot Shield VPN programming you can unblock YouTube, unblock Facebook or unblock any locales from anyplace.
Secure your IP address – VPN programming empowers you to ensure your IP address so you can appreciate private perusing and keep programmers and spammers from checking your online exercises.
Surf the Web secretly – By making an encoded burrow between your PC and Hotspot Shield servers, Hotspot Shield empowers you to surf the Web namelessly without being followed or kept an eye on.
Hotspot Shield Crack
EaseUS Data Recovery Crack
4K Video Downloader crack
FL Studio 20 crack
Windows 7 Loader
Mastercam Crack
Full Cracks
Windows Activator
Crack Software
×