Replacing bulb Braun Paxiscope XL

blades are blunt and the hair gets stuck between the clipper blade and the fixed blade
have them sharpened or replace with new one s

TEST THE CONTINUITY OF THE BULB AND THE WIRING AND THE PARTS INSIDE.


DOES THE UNIT STILL WORKS NORMALLY ASIDE FROM THE BULB?

The oven lights are 12-volt, 5-watt maximum halogen bulbs. They
will come on when the oven door is opened. On double oven
models, both upper and lower lights will come on when either
door is opened. The oven lights will not work during the Self-
Cleaning cycle. When the oven door is closed, press OVEN
LIGHT to turn them on or off.
To Replace:
Before replacing, make sure the oven is off and cool.
1. Disconnect power.
2. Remove glass light cover by grasping the front edge and
pulling away from oven




3. Remove bulb from socket.
4. Replace bulb, replace bulb cover by snapping back into wall.
5. Reconnect power.

Most common cause will be the blades have gone dull and should be sharpened or replaced. Check that the 2 screws on the blade latch assy are tight where it screws onto the front housing, blade off to check them. 3rd thing to check is for excessive wear in the lever that drives the blades, if it is worn replace it.

"Replacing fog light bulbs on 2013 Santa Fe". Raise vehicle if you are a big person. In front of front wheels triangular plastic panels exists. Remove Phillips head plastic screws in chosen panel (2ea). Pull panel down. Stick hand through opening, remove wiring connector from bulb. (Bulb will not come out unless you do). Twist bulb housing counterclockwise and remove. Install new bulb, reverse procedure and don't touch the glass part of the bulb.

Replace Projection Lamp/Bulb A1601-753A (XL-2000U) THIS ONE IS ON THE RIGHT FRONT COVER REMOVE THE COVER BY PULLING OUT THE LIGHT IS RIGHT THERE YOU NEED TO REMOVE 2 SCREWS Replacement Projection Lamp/Bulb A1601-753A (XL-2000U)

Hello Weaver124!
Open the tailgate(s) completely and you'll find two phillips-head screws on the inside edge of the tail light assembly. Take out those two screws (keep one hand on the assembly when you remove the last screw) and the whole tail light assembly will come off of the vehicle. On the back side of the tail light assembly, twist and remove the light bulb housing for the blown bulb. The bulbs themselves on some models vary in the manner in which they are removed: (1) If the base on the bottom of the bulb itself is a *round* brass base, press down on the bulb then twist it to remove it, or (2) If the base on the bottom of the bulb itself is *flat* plastic, pull the bulb straight out of the assembly. To replace the bulb, simply reverse the order. Best wishes!

Locate the headlight socket cover inside the engine compartment. The cover is on the back of the headlight assembly; it is round and made of plastic or rubber.

2 Remove the headlight socket cover by pulling it off or twisting it to the left and then pulling it off. You can see the headlight socket once the cover is removed.

3 Grip the headlight socket, turn it to the left and pull it out of the assembly. The light bulb is connected to the socket.

4 Pull the bulb straight out of the socket and discard it in a waste receptacle.

5 Plug the replacement bulb into the socket, taking care not to touch the glass. The oils on your skin can shorten the life of the bulb if you touch the glass. Wear gloves to prevent touching the glass.

6 Place the socket back into the light assembly and turn it to the right to lock it in place.

7 Slide the headlight socket cover over the socket and press on it to secure it, or turn it to the right, depending on how you have removed it in Step 2.

8 Repeat Steps 2 through 7 to replace the other headlight bulb.

please give good rateing if this helps thank you

You rotate the front rim of the lens.

Usually, one has to get the entire headlight assembly to replace the lens.
Is it cracked?
If it is just faded, try some anti-haze polish for headlights. This can save you some money compared to restoring the headlamp by replacing the assembly (which may be available from a salvage yard).

---
REMOVAL & INSTALLATION

CAUTION
Halogen bulbs contain gas which is under
pressure. Handling the bulbs incorrectly could cause it to shatter into flying
glass fragments. Do NOT leave the light switch ON. Always allow the bulb to cool
before removal. Handle the bulb only by the base; avoid touching the glass
itself. Whenever handling a halogen bulb, ALWAYS follow these precautions:

• Turn the headlight switch OFF and allow the bulb to cool before
  changing it. Leave the switch OFF until the change is complete.
  
• ALWAYS wear eye protection when changing a halogen bulb.
  
• Handle the bulb only by its base. Avoid touching the glass.
  
• DO NOT drop or scratch the bulb.
  
• Keep dirt and moisture away from the bulb.
  
• Place the used bulb in the new bulb's package and dispose of it properly.
  

Cirrus, Stratus, Sebring Convertible and Breeze

1. Open the vehicle's hood and secure it in an upright position.
   
2. Disconnect the negative battery cable.
   
3. Remove the 2 screws securing the headlight module to the radiator closure
   panel.
   
4. Pull out the headlight module from the vehicle.
   
   
   
   
   
   Fig. 1: Using a Torxhead screwdriver, remove the 2 headlight
   module retaining screws
   
   
   
   
   
   
   
   Fig. 2: Pull the headlight module straight out of the front of
   the vehicle to remove the bulbs
   
   
   
   
   
   
   
   Fig. 3: Disconnect the wiring harness for the headlight bulb
   
   
   
   
   
   
   
   Fig. 4: Turn the light bulb retaining ring counterclockwise,
   and remove it from the back of the module
   
   
   
   
   
   
   
   Fig. 5: Pull the light bulb out from behind the module. Never
   touch the glass of the light bulb
   
   
   
   
   
5. Detach the headlight electrical connector.
   
6. Remove the retaining ring holding the bulb to the back of the headlight
   module.
   
7. Pull the bulb from the back of the headlight module. Hold the bulb by its
   base only; try not to touch the glass itself.
   To install:
   
   
8. Holding the bulb by the base, place it in the headlight module, then secure
   with the retaining ring.
   
9. Attach the electrical connector to the bulb.
   
10. Install the headlight module into the vehicle and tighten the 2 retaining
    screws.
    
11. Connect the negative battery cable and check the headlight operation.
    

Sebring Coupe and Avenger

1. Open the vehicle's hood and secure it in an upright position.
   
2. Disconnect the negative battery cable.
   
3. Remove the sealing cover by rotating it counterclockwise.
   
4. Remove the bulb attaching spring and pull out the light bulb.
   
   
   
   
   
   Fig. 6: Remove the headlight sealing cover(s)
   
   
   
   
   
   
   
   Fig. 7: Remove the attaching spring and pull out the bulb
   
   
   To install:
   
   
5. Install the bulb into the headlight module.
   
6. Install the bulb attaching spring.
   
7. Install the sealing cover.
   
8. Connect the negative battery cable and check the headlight operation.