My samsung LED TV turns on sometines and other times the red light stays on and won't respond to remote control

Setup codes to check with Samsung TV are: 0105 0077 0076 0109 0007 0009 0004 0005 0085 0172 0942 0358 0012 0015 0080 0104 0106
Direct Code Entry

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

Code Search
If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.

1. Manually turn on the device (TV, VCR, etc.) to be controlled.
2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
5. Press and release MUTE to install the code. The indicator light goes off.

Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.

IDENTIFYING CODES FOUND USING THE SEARCH PROCEDURE

1. Press and hold the SETUP until the LED indicator lights steadily. Release Setup button.
2. Press the mode button that matches the equipment you want to identify. The LED blinks once.
3. Press and release SETUP. The LED blinks once.
4. To find the first digit, press each number button from 0 to 9 until the LED blinks. The number you pressed is the first digit of the code.
5. Press each number button from 0 to 9 again as above to find the second digit.
6. Press each number button from 0 to 9 again as above to find the third digit.
7. Press each number button in turn to find the fourth digit. When the fourth digit has been found, the LED goes out.

Try a code search method.
Code Search
If after trying "Direct Code Entry" your device does not respond, or if your brand is not listed, try doing a search of the code library for your code by following these steps.

1. Manually turn on the device (TV, VCR, etc.) to be controlled.
2. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
3. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks once, then stays on.
4. Press the CHANNEL UP button repeatedly (up to 300 times) until the device to be controlled changes channel. The red indicator blinks, then stays lit.
5. Press and release MUTE to install the code. The indicator light goes off.

Most users will want to store VCR codes under the VCR button, Cable codes under CBL, etc. If you want to store a VCR code under CBL, etc., first follow the procedure for Direct Code Entry and press CBL in step 2 of Direct Code Entry, then enter ANY VCR code in step 3 of Direct Code Entry. Then follow the steps above for Code Search.

IDENTIFYING CODES FOUND USING THE SEARCH PROCEDURE

1. Press and hold the SETUP until the LED indicator lights steadily. Release Setup button.
2. Press the mode button that matches the equipment you want to identify. The LED blinks once.
3. Press and release SETUP. The LED blinks once.
4. To find the first digit, press each number button from 0 to 9 until the LED blinks. The number you pressed is the first digit of the code.
5. Press each number button from 0 to 9 again as above to find the second digit.
6. Press each number button from 0 to 9 again as above to find the third digit.
7. Press each number button in turn to find the fourth digit. When the fourth digit has been found, the LED goes out

To have the remote try each TV code it knows one at a time, follow these steps:

1. Turn on your TV.
2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
3. Press the TV button on the remote so that the LED blinks once and then remains solid red.
4. Press the ON/OFF button slowly and repeatedly until the TV turns off. The LED will blink once each time you press the ON/OFF button.
   
5. Once the TV turns off, press the ENTER button to store the code and the LED will turn off.
   

I hope that helps.

You might consider the auto-search function.

To have the remote try each TV code it knows one at a time, follow these steps:

1. Turn on your TV.
2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
3. Press the TV button on the remote so that the LED blinks once and then remains solid red.
4. Press the ON/OFF button slowly and repeatedly until the TV turns off. The LED will blink once each time you press the ON/OFF button.
   
5. Once the TV turns off, press the ENTER button to store the code and the LED will turn off.

I hope that helps.

Make sure you try every code in the list for your JVC TV.
The codes for your Jumbo Universal Remote to control a JVC television are 013, 054, 055, 060, 065, 067, and 089.

To program your remote by entering a code, follow these steps:

1. Turn on your TV.
2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
3. Press the TV button on the remote so that the LED blinks once and then remains solid red.
4. Enter the first set of 3-digit codes from the list. The LED will blink once every keypress. After the 3rd digit, the red LED will turn off indicating that the code was recognized for the device. If the code was not compatible, the LED will flash several times and you need to return to step 2 to try that code again or to try the next code in the list.
   
5. After the LED has turned off, aim the remote at the TV and press ON/OFF. If the device turns off, you have used the correct code and the remote was successfully programed. If the device does not power off, return to step 2 and try again with the next code in the list.
   

To have the remote try each TV code it knows one at a time, follow these steps:

1. Turn on your TV.
2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
3. Press the TV button on the remote so that the LED blinks once and then remains solid red.
4. Press the ON/OFF button slowly and repeatedly until the TV turns off. The LED will blink once each time you press the ON/OFF button.
   
5. Once the TV turns off, press the ENTER button to store the code and the LED will turn off.
   

I hope that helps.

To program your remote by entering a code from a manufacturer's list, follow these steps:

1. Turn on your TV.
2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
3. Press the TV button on the remote so that the LED blinks once and then remains solid red.
4. Enter the first set of 3-digit codes from the list. The LED will blink once every keypress. After the 3rd digit, the red LED will turn off indicating that the code was recognized for the device. If the code was not compatible, the LED will flash several times and you need to return to step 2 to try that code again or to try the next code in the list.
   
5. After the LED has turned off, aim the remote at the TV and press ON/OFF. If the device turns off, you have used the correct code and the remote was successfully programed. If the device does not power off, return to step 2 and try again with the next code in the list.

To have the remote try each TV code it knows one at a time, follow these steps:

1. Turn on your TV.
2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
3. Press the TV button on the remote so that the LED blinks once and then remains solid red.
4. Press the ON/OFF button slowly and repeatedly until the TV turns off. The LED will blink once each time you press the ON/OFF button.
   
5. Once the TV turns off, press the ENTER button to store the code and the LED will turn off.
   

I hope that helps.

To have the remote try each TV code it knows one at a time, follow these steps:

1. Turn on your TV.
2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
3. Press the TV button on the remote so that the LED blinks once and then remains solid red.
4. Press the ON/OFF button slowly and repeatedly until the TV turns off. The LED will blink once each time you press the ON/OFF button.
   
5. Once the TV turns off, press the ENTER button to store the code and the LED will turn off.
   

I hope that helps.

To have the remote try each TV code it knows one at a time, follow these steps:

1. Turn on your TV.
2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
3. Press the TV button on the remote so that the LED blinks once and then remains solid red.
4. Press the ON/OFF button slowly and repeatedly until the TV turns off. The LED will blink once each time you press the ON/OFF button.
   
5. Once the TV turns off, press the ENTER button to store the code and the LED will turn off.

I hope that helps.

I recommend using the autosearch function of your remote.

To have the remote try each TV code it knows one at a time, follow these steps:

1. Turn on your TV.
2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
3. Press the TV button on the remote so that the LED blinks once and then remains solid red.
4. Press the ON/OFF button slowly and repeatedly until the TV turns off. The LED will blink once each time you press the ON/OFF button.
   
5. Once the TV turns off, press the ENTER button to store the code and the LED will turn off.

I hope that helps.