Top 20 U-Line Icemaker Questions & Answers

because it is an automatic machine

Tell him to first fill ref-regent gas in compressor cause if does not have enough the comp will over heat a cut of .

It does sound as if you may need a new ice maker. Other than that does the compressor come on to keep the ice cold? If so is it making any type of noises beyond the typical hum?

Sorry we do not sell this product or any other. Please contact the manufacturer.

leaking water tray or water level to high check for any cracks and check water level after first harvest

If water keeps running after the fill cycle is usually indicates a bad fridge inlet valve. This valve controls the amount of water going into your icemaker. It is found where the water line goes into the fridge, usually in the back of the fridge at the bottom. You would need to cut the power to the fridge, turn off the water supply going into the fridge and remove a panel to get to it. You can check out online what a fridge water inlet valve looks like so you can identify it. It usually has 1-2 water lines going into it and 1-2 wire harnesses attached. You can buy new ones at a appliance parts store or online. If you need further help, I’m available over the phone at https://www.6ya.com/expert/rick_b814bade9ade93ea

This is usually caused by a bad water inlet valve. This part is usually found behind the fridge at the bottom behind a panel on the fridge itself. It has 1-2 water lines running into it and 1-2 wire harnesses connected. You need to turn off the water going into the fridge and cut the power to the fridge to access this part. You can buy a new one at a local appliance parts store or online. If you need further help, I’m available over the phone at https://www.6ya.com/expert/rick_b814bade9ade93ea

Possible water valve leaking thru

The water valve is normally situated at the bottom rear of the fridge. Follow the water line/ hose to the inside of the fridge at the back compartment and you will find it. With the water AND the power unplugged / turned off, you can remove the water hose fittings and there is usually only 2 wires to the valve.. The water valve itself should only be mounted with a couple of screws or on a bracket. refit everything with the new valve. Slowly turn the water back on first and make sure there are no leaks.

Make sure normal drain line (located under the ice) is not clogged. Check gaskets and seals. Also make sure everyone who uses it closes the door completely and does not leave it cracked open. And make sure no one has screwed any thing into it and punctured through it. A screw alone will not keep the water in.

After the cleaning cycle, if you drained the tank to get rid of the cleaning/descaling solution, you will have to refill the machine for the initial start. The normal freeze/ harvest cycle will normally fill the unit after the initial start. I have seen several ice makers with this same initial problem. If this is not the case and your reservoir is full of water, then check water supply to make sure water will flow all the way into the reservoir. Sometimes the makeup water solenoid fails and need replaced. So if cleaning cycle works and fills, solenoid operated water valve is not the problem. If would mean some electric component is not working. The on/off/clean switch not sending on signal. The board, which is located under the top panel of the cabinet, may have a bad contact on the board. Another possibility is the water level sensor may not be in contact with the water. Most units will not start if the water sensor is not in contact with the water level. It normally looks like a metal probe and has a wire connecting to it to the control board. Any parts can be found by taking your model number to Searspartsdirect.com and can be ordered using a credit card and be delivered to your home. Hope this helps

What's the make and model. ..maybe mechanical

Turn off the machine if water is still running then unplug the machine. If the water is still running then check water presser from water supply to make sure it is under 80 psi before replacing water inlet valve.

Most door gaskets can bought from a roll at appliance parts dealers, or: www.appliancepartsonline.net

Push one of the keys to see if display is to reset. or turn and off via the display key pad. or unplug the unit for one minute then plug back in if any of these steps return the unit back to operation the unit was probably accidentally entered into a service mode.

Yes its hard to get out but it will come out after you removed all the screws that you said came out the ice maker sets on a plate it is glued to it you will just have to pry it loose from the plate and it will come loose. if you remove the cabinet off that holds the ice bucket it is allot easier to get to.

plug it back in remove the bottom cover and and Push rocker switch to freeze.

Replace water inlet valve.

the sensor that sits on the evaporator may be faulty

Call sears with model