Sharp Aquos LC-42D62U 42 in. LCD HDTV - Answered Questions & Fixed issues
What is opc that pops up about every 10
Min
OPC is optical picture control. The television is adjusting itself to the lighting in the room. Even if someone walks in front of the television's sensor it will start to adjust and you will see opc on the screen and green leaves.
You can leave the feature on without the opc and green leaves appearing on the screen. Press the menu button. Scroll down to OPC. Press enter. Scroll to on. Press enter. Press menu to exit.
12/28/2023 6:33:59 PM •
Sharp Aquos...
•
Answered
on Dec 28, 2023
•
3,761 views
I can look at tv for about hour and then it will start turning off. After it has that for 2 times you cant turn it back on for hours
Fault to the main power supply regulator section. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/
It will be best to replace the power supply regulator board as card basis rather than making "Surgery" to it; which usually will make loss for both money and time. Even though you can make it right, it will cost around an amount equal to the cost of a new board; including the cost of (spare parts + service charge) More to say, most of the spare parts to it will be difficult to get from open electronic spare part market. This is true to most of the flat panel TV power supply boards; irrespective of its brand and screen size.
12/28/2019 4:11:57 AM •
Sharp Aquos...
•
Answered
on Dec 28, 2019
•
170 views
Sharp Aquos LC-42D62U VOlume Control
OK guys I'll save you. The tv is in hotel mode. To get it out from there you have to go in service menu but DO NOT CHANGE ANY OTHER THING IN THERE, only what i tell you. With the tv on and the K letter on the screen press in the same time vol- and ch- on the tv set. Now you'll be in service mode. On the remote press down arrow (not -channel) and you'll see up industry init. go there with ch- and press vol+ and enter. let the tv like that for few seconds and the tv will go green and hopefully industry init succsesfull will be on the screen. After that unplug the tv and replug it. Done!
6/2/2019 5:41:09 PM •
Sharp Aquos...
•
Answered
on Jun 02, 2019
•
17,455 views
My tv aquos sharp LC
Sharp. LCD TV model NOS.LC32L400M green led light blinking continue no pictures old solutions
4/5/2018 4:07:20 PM •
Sharp Aquos...
•
Answered
on Apr 05, 2018
•
918 views
Red line in the middle of my plasma screen
Hi leprecoce,
One transistor out of millions has failed shorted. That is an unusual failure mode, but not unheard of. The chip can probably be replaced, you might want to check google maps or
http://tvrepair.com for a repair shop near you.
Most shops should be able to give you an estimate, I would guess around $300, unless the chip is hard to get.
12/5/2017 10:41:51 PM •
Sharp Aquos...
•
Answered
on Dec 05, 2017
•
429 views
We have over the air T.V. On digital channel 9.1
switch TVs and see what happens. If the problem now occurs on the old TV, it is the TV. If the problem occurs on the new TV, it is the location. But use a ground fault tester in case that socket has some kind of ground fault
11/3/2017 4:24:27 PM •
Sharp Aquos...
•
Answered
on Nov 03, 2017
•
189 views
I have a DDTV stb
Capacitors (mostly on power supply circuit but also other cards) low capacity (due to old age and poor quality). Need specialized service.
9/11/2017 11:47:58 AM •
Sharp Aquos...
•
Answered
on Sep 11, 2017
•
152 views
SHARP Aquos 42D62U No picture.
Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/
In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
8/15/2017 2:32:47 PM •
Sharp Aquos...
•
Answered
on Aug 15, 2017
•
418 views
My Sharp LC-42-D62U won't power up. The power
Ur Tuner signal board have problems or dead.Ur power LED light indicator stable for a few mins before the power LED light,and the OPC LED light indicators flashes?After the POWER light and OPC light indicators flashes,just push the power button again for the power recycles again.Probally have to pushes the power button 3 or 4 for power light and opc light indicators flashes,the LCD backlght will lght up and work.Sharp tv have this problems alot,very common in Sharp LCD tvs.
11/28/2016 7:36:43 AM •
Sharp Aquos...
•
Answered
on Nov 28, 2016
•
4,869 views
Snowey on scrreen
Hi there,
I've been repairing TV's for over 15 years and I would say either a bad Tcon's or main board issue. Theirs no need to replace capacitors these days, you can get the main board from $40-60.
Have you tried using different devices on the unit? If your getting a snowy picture on a satellite receiver, check with your provider for troubleshooting guide their unit. Or let me know the provider and I can lead in you right direction.
Thanks,
Jason If you need further help, I’m available over the phone at
https://www.6ya.com/expert/jason_70466cb634a57543
6/9/2016 6:01:14 AM •
Sharp Aquos...
•
Answered
on Jun 09, 2016
•
274 views
Has developed a small horizontal line on the screen
Beauty tips is natural whenever can get; simply keep hydrated by drinking lots of water. It'll help keep skin color looking aged fresh. The skin is an income organ which needs water, and denying it water generate it dull and departed. Drinking plenty of water will keep skin hydrated and impressive. It will also reduce variety of breakouts your skin has, reliant on your form.
http://slimbodyketone.co.uk/hydroplenage/
11/28/2016 7:42:54 AM •
Sharp Aquos...
•
Answered
on Nov 28, 2016
•
112 views
Why won't it turn on?
Check the remote control for its infra-red emission. Check it with fresh batteries. Check by pressing all the buttons on it; and see whether all of it generates infrared signal while pressing. If it is found OK, check and replace the infrared sensor inside the TV.
Also there can be Fault in the main power supply regulator section. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts.
http://electro-medical.blogspot.com/
11/19/2015 4:15:52 AM •
Sharp Aquos...
•
Answered
on Nov 19, 2015
•
110 views
Not finding what you are looking for?