20 Most Recent
HP Photosmart C6180 All-In-One InkJet Printer - Page 5 Questions & Answers
The color of my print is very pink and yellow with no blue
If your printer has 3 colored ink cartridges, your cyan (blue) cartridge is empty. Replace it with a new one. If your printer has just one colored ink cartridge, the blue section of it is empty. Replace the cartridge with a new one. You'll find the correct cartridge (normally a number) in the owners manual and/or on the cartridge itself. See the owners manual for instructions on where the cartridges are located and how to replace them.
How do I fix my hp c6180 printer with error code
A similar error (0xc19a0035) started occurring on my printer and eventually it would constantly power
on and off. Apparently some defective components were used in the
construction of the logic board (see photo). On my C6180 there were 3
failed capacitors (the green cylinders - the puffed top indicates
failure) and a 4th from the same manufacturer (TEAPO - many unfavorable
web references to this manufacturer). I purchased 3x 330uF 16V and 1x
680uF 10v rated to 105 degrees Celsius (total about 60cents). On the
logic board, the capacitors I replaced are labeled C613, C614, C660 and
C662. If you are not comfortable replacing the parts yourself (or don't
have a soldering tool), you will have to find someone who will. The time
to repair should be less than 30 min - I did it in 25 min with only a
solder pen. This also fixed the ink system failures the printer was
having. A similar fix may apply to other printers.
How do I fix Error code Oxc18a0206?
Hello, U may try these steps FIRST -
1 Disconnect the Universal Serial Bus (USB) cable from the back of the product, but leave the product turned on.
2. Open the cover of the product and remove the print cartridges.
3. Close the cover and wait for the Insert Ink Cartridges message to display.
4. Disconnect the power cord from the back of the product and the wall socket, then wait for one minute.
5. Reconnect the power cord. If the product does not automatically turn on, press the Power button.
6. Open the cover and reinsert the print cartridges.
7. Close the cover. If prompted, print a calibration page.
8. Reconnect the USB cable, and try to print a print job from the computer.
In case the above steps does not help , You may try the following steps SECOND -
Get the unit into the "Support Menu" by following the steps below according with the product, see the steps below:
A.- Press and hold the "*" key. B. - Press the "#" key and release both keys. Display should say "Enter Special Key Combo" C. - Press and release in sequence the "1", "2" and "3" buttons.
2. Press and release the right arrow button until the display says "System Configuration Menu".
3. Press and release the "OK" button.
4. Display should say "Hardware failure status". If not there already, Arrow Key over to "Hardware failure status",
5. Press and release the "OK" button.
6. Display should say "Hardware failure status: Clear. Press OK to clear".
7. Press and release the "OK" Button. Message changes to "Hardware failure status Cleared. Press Cancel to continue".
8. Press and release the "CANCEL" button as many times as necessary, so that, either the "Welcome to Photosmart Express" screen appears, or, the "Ink System Failure" screen appears. PLEASE DO NOT TRY TO PRINT AT THIS STAGE.
9. Using the Power Button, turn the unit OFF and unplug the power cable from back of the printer and wall outlet.
10. Wait 30 seconds for the power to get discharged and then plug the power cable into the wall outlet first and then into the back of the printer
11. Turn the unit on. The printer may display message "USE POWER BUTTON TO SHUTDOWN THE PRINTER" followed by "PRESS OK TO CONTINUE". Press OK. The Printer will start the "ONE TIME INK INITIALIZATION PROCESS". Allow this process to complete and do not interrupt. Once the initialization process is complete, the printer will print out a Diagnostic Page.
12. To verify printer functionality print a SELF TEST PAGE. If SELF TEST prints, then printer is ready for use or Software Installation.
I hope this helps !!!!
If the error is still there, sorry U are out of luck - might need to change the printer as per me.
Regards
PS
Cannot print with wirelessly networked printer
hi,
if printing from 2 other computer works fine, will i think its not an issue of IP address which changes somehow. but anyways, try to check if you still have other printer drivers under "PRINTERS" (see control panel). it should say HP Photosmart c6100 series. If you also have there a printer icon that says HP Photosmart c6100 series Copy1, try using it (right click on that icon and choose Set as Default Printer). If you only have HP Photosmart c6100 series under PRINTERS, try to right click, then choose properties. When Properties box is open, click on PORTS tab. then click on configure ports below. Try to type in the IP address of the printer under "Printer Name or Host name or IP address". make sure that you already printed network configuration page to get the exact ip address of the printer, Dont know how to print? do this.
PRINTING NETWORK CONFIGURATION PAGE
1. press setup, then scroll down and look for Network.
2. press okay on network, it will give you the first option "VIew network settings".
3. press okay on it, and it will give you the first option "Print network configuration page."
4. choose that and press okay. it will print the network config page. from this document, you will be able to see the IP address of the printer.
Please let me know if the issue is still not resolve so that i can go ahead and give you another possible solution.
Thank you so much.
adonscott
Replace old car.with new ink car.still saying to change
Look inside the printer where you installed the cartridge. Clean the metal contacts on cartridge and the corresponding contacts in the printer. Do this with cue tips dipped in rubbing alcohol. Then reinsert cartridge and then turn off printer. Wait a few seconds and then turn it back on.
How to override error Oxc18a0001
If you have a C6180, the error code you give here is not in the manual, so you better contact HP service centre like the manual explains.
How do I manually clean printer heads on an HP C6180 all in one printer?
This is a job best left to a shop. However, if you are bound and deternined, as well as, experienced it can be done. You will have to disassemble the machine to got to the rail the print head slides back and forth on. At that point remove the rail and slide the print head off. An alcohol bath with a soft bristle brush should clean it up nicely. Reassemble it in reverse order. Adjust and calibrate and you should be good to go. Get a tech manual for the printer. It will save you time and aggravation. You nay be able to find one at feedroller.com.
Hp c6180 all-in-one error message 83c00020
Hello,
Try unplugging the printer from power for about 10 minutes and then reconnect it and see if that will reset it. You mentioned the error code 83c00020 is that on the printer screen or somewhere else?
I wasn't able to find that exact error is that the way the error actually displayed?
Reply back and let me know. Hope this helps. Please remember to rate this information.
Thanks
HP C6280 won't print red color
Hi,
1> Please check it color setting. Go to Control panel and printer option choose and right click go to printer property and color section check it only other color setting or not, better default setting and save it.
2> Printer cartridge removed and clean soft hand and proper connect again.
3> Have you printer driver then old driver removed and again reinstalled printer software.
4> Installation before removed infected virus in PC.
Thanks,
HP Printer Support
Not finding what you are looking for?
