20 Most Recent Danby DWC283BLS Wine Cooler - Page 9 Questions & Answers

HI,

I have been through your problem but i don't think there is any appropriate solution for this.All i can say it can be a bad compressor and you'll have to get it repaired.

Now just do one thing if you need other expert's advice on this then just rate me as thanx for trying in the premium problem whose solution you accepted as fixya.Your question will be reposted then so that other experts can give you advice.

Goodluck..

these units have a condensor cooling fan in the rear it appears that yours may be seized up.
Regards
Advisor

not hard to replace but you are correct if it is not cycling off at the temp you want it to then the temp control is the problem

THE LAST THING THAT EVER HAPPENS IS FREON LOSS.

 

SO TRY THIS FIRST ...

 

LET THE COOLER STAND WITH "NO POWER FOR 24 HRS.

MAKE SURE IT INSIDE AT ROOM TEMP. NO HIGHER THAN 75 deg. AFTER THE ALOTTED TIME TURN THE T-STAT-"OFF" AND TURN THE POWER "ON" ...

THE CONDENSER FAN SHOULD START IMMEDIATELY. NOW LISTEN REAL CAREFULLY BY THE COMPRESSOR TO HEAR ANY CLICK NOISE. IF YOU DO THAT IS THE EXTERNAL OVERLOAD ( bI-METAL SAFTEY T-STAT THAT PROTECTS THE COMPRESSOR. TURN POWER OFF AGAIN AND DO THE FOLLOWING.

 

THERE IS : 1) A START (plug-in) RELAY THAT PLUGS INTO THE COMPRESSOR.

2) THERE IS A START ASSIST CAPACITOR MOUNTED USUALLY ON THE TOP OF THE COMPRESSOR TEREMINAL COVER.( THIS IS HELD ON WITH A METAL STRAP THAT CAN BE "POPED-OFF" WITH A SCREW DRIVER. OR IT MAY HAVE 2 MOUNTING SCREWS.

3) THERE IS A ROUND BI-METAL T-STAT THAT PROTECTS YOUR COMPRESSOR.(AS STATED ABOVE).

 

MAKE A DRAWING OF WHERE EVERY WIRE GOES AND THE DEVICES ON PAPER. .... THEN ... AND ONLY THEN REMOVE ALL 3 PARTS AND TAKE THEM TO YOUR LOCAL APPLIANCE REPAIR OUTLET. eg. APPLIANCE PARTS. APCO ETC.

THEY WILL CHECK ALL 3 COMPONENTS FOR YOU AND MOST ALL HAVE UNIVERSAL REPLACEMENTS FOR ALL 3 DEVICES NO MATTER WHAT BRAND YOU HAVE.... AND THEY SHOULD BE ABOUT $10-$15 EACH.

I HAVE REPAIRED HVAC & REFRIGERATION EQUIPMENT FOR OVER 40 YEARS. WHAT I DO IS REPLACE ALL 3 DEVICES. IF ONE IS BAD IT TENDS TO OVERHEAT THE OTHER COMPONENTS AND WEAKENS THEM.

 

NOTE: NEVER INSTALL REFRIGERANT SELFTAPPING VALVES TO CHECK FOR FREON ... A AMP DRAW WILL TELL YOU IF COMPRESSOR IS RUNNING AT FULL LOAD , AND AT THE EVAPORATOR YOU SHOULD HAVE A 10-20 DEG F. DROP IN TEMP. YOUR EVAP COIL SHOULD FORM A EVEN FROST ON IT IN ABOUT 2-3 HOURS.

THE MAIN THING IS TO ENSURE COMPRESSOR IS RUNNING.

IF YOU HAVE A THERMOMETER, THE LARGER COPPERLINE ON THE COMPRESSOR SHOULD BE ABOUT 50-60 DEG.AND EVENTUALLY WILL "SWEAT". THE SMALLER LINE SHOULD READ 120-150 DEG "AT THE COMPRESSOR" OUTLET CONNECTION.

MAKE SURE YOUR CONDENSOR AND EVAPORATOR COILS ARE BOTH ABSOLUTELY CLEAN. (CHECK WITH SMALL BRIGHT FLASH LIGHT TO SEE THROUGH COIL FINS.

 

THAT SHOULD SOLVE YOUR PROBLEM. YOU MAY FIND WHEN TAKING THE PARTS OFF ... A BROKEN OR BURNT WIRE. IF SO REPLACE IT WITH AT LEAST #12 STRANDED WIRE.

 

PROPER WIRE AND TERMINALS ARE AVAILABLE AT THE APPLIANCE PARTS STORE IN YOUR AREA.

 

GOOD LUCK ... JOE_REX

Does it have a compressor and does it run? If so there is probably a relay on that board that is bad or only runs with the compressor.

Sometimes the bearing gets dry. Take it out and try to put a small amout of household/3M oil on the shaft to see if it helps. Some have small holes that are for putting oil into to feed the bearings.. You may be able to do this without taking it out. Be very sparing with the oil to prevent getting too much in it.

I don't know what temperatures it should hold, but try cleaning out any radiator ribs on the back/underside. If there get clogged with dust and dirt they don't get rid of the heat as easily, and that will cause it not to cool as it should. Also check any thermostat settings if there is such a thing on it.

just give me your number iwill call u

Your budget determines how much quality the sofa has

If the foot of your Simmons Nuflex bed will not raise, there may be an issue with the motor or the lift mechanism. Here are a few things you can try to fix the problem:

1. Check the remote control: Make sure the remote is properly functioning and the batteries are not dead. Also, check that the foot lift button is not stuck.
2. Check the wiring: Check the wiring between the remote, the lift mechanism, and the motor for any frayed or disconnected wires. If you find any damaged wires, they will need to be repaired or replaced.
3. Check the lift mechanism: Inspect the lift mechanism and look for any visible damage or debris that may be preventing the foot from raising. Clean the lift mechanism and lubricate it with light oil.
4. Check the motor: If the motor is not functioning properly, it may be preventing the foot from raising. If the motor is faulty, it will need to be replaced.

If you are not comfortable with these steps, or if the issue persists after trying them, it may be best to contact Simmons customer support or a professional technician for further assistance. They may ask you to provide your bed's serial number and other information to help troubleshoot the problem.

Question edited to remove Funky-Dash-Use- :>D Lots of pretty pictures, but no instructions. If it is new, reach out to the store or the online seller. It looks pretty easy by looking at the pictures and zooming in on the B&Q website. Lay all the parts out. https://www.google.com/search?q=Colorado+metal+4+seater+dining+set+with+parasol+assembly+instructions ..