20 Most Recent Konica Minolta 1149-0291-01 Minolta Cs Pro Ep 2080 Ep 3000 Copier Drum - Page 8 Questions & Answers

You don"t buy a new one

What is the model and the code is C8650??????

Registration motor (M5) Printer control board (PRCB) ADU drive board (ADUDB) Any of the one above, but I would start with the Motor check the registration roller its the big roller (length wise prior to the drum section.

Cooling fan on the Main board is in operative. See if you genteelly clean it if not need new board!!!$$$$$$$

Unless you have access to the MY Konica Minolta Web site you will not be authorized to have access to it Copier firmware belongs to Konica Minolta

The model number would help?

Does the first tray display on the control panel or does the machine state that 1st draw is unavailable? Go to service mode and reset the first draw electrically.

Replace the hard drive

Any reset will wipe the memory and network settings so I would recommend you have tech look at it and see if you can save all setting before wiping clean Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Need to access service mode to enter serial number if you don't enter correctly then machine will lock out. I recommend you have a tech do this. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

There is a problem in fax setup menu. Be sure you s are set to AUTO

Your email server is miscfgigured

Hi Onyejekwe- I found this link. https://printcopy.info/?l=en&mod=erc&brand=Konica-Minolta&model=bizhub%20C25&code=0502 Hope this helps.

Sir/Mam, Turn off the main power switch, ensure the sub power switch is on. The sub power switch is located on the right side of the control panel. Then holding down the Utility/Counter button turn the main power switch on. Close the front door you must keep the Utility button down. The screen will show TROUBLE RESET touch it sees a "OK" then power off the machine. YOU MUST WAIT TEN SECONDS BEFORE POWERING UP AGAIN!!!!!! If the problem goes away OK. If the code comes back, you need a Fusing unit ( DO NOT KEEP TRYING TO RESET THE MACHINE! THE MACHINE IS TELLING YOU THERE IS A PROBLEM!!!!! A Fire could occur and that would ruin a perfectly good day!!!! Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

A search using https://www.google.com suggests the following:

• Code: C-2401
• Description:The erase lamp (EL) is unconnected.
• Causes:Erase lamp (EL)

https://printcopy.info/?l=en&mod=erc&brand=Konica-Minolta&model=bizhub%20601&code=C-2401 Web site above includes a link to a service manual.

Turn off the machine, remove the toner bottle, then power on with the bottle out let the machine do its start up procedure. one it asks for the toner bottle install it correctly

Bizhub C450 Manuals (english) https://www.konicaminolta.eu/eu-en/support/download-centre Error code list https://printcopy.info/?l=en&mod=erc&brand=Konica-Minolta&model=bizhub%20C450

• Code: C0211
• Description:Manual tray rise descent error • The bypass lift-up sensor is not blocked even when the tray 2 vertical transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the standby position to the feed position was started. • The bypass lift-up sensor is not unblocked even when the tray 2 vertical transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the feed position to the standby position was started.
• Remedy:1 Check the M103 connector for proper connection and correct as necessary. 2 Check the connector of M103 for proper drive coupling and correct as necessary. 3 PC115 I/O check PWB-Z PJ7Z<A>-11 (ON) T to U-25 4 M103 operation check PWB-Z PJ5Z-5 to 8 T to U-22 5 Change PWB-Z.

Lo siento no tengo los recursos en espa?ol

Please the copier model exactly.

If you have lost the Bizhub manual you can find it here https://kmbs.konicaminolta.us/wps/wcm/connect/newweb/b6c3af14-17d2-40a0-9c96-de452ca7c836/bizhubHDDSecurityGuideC650_C353_751_501.pdf?MOD=AJPERES&CONVERT_TO=url&CACHEID=ROOTWORKSPACE.Z18_H0261AK0LG7QE0AE0BVQU730H1-b6c3af14-17d2-40a0-9c96-de452ca7c836-mJm5PTq

There is another cover at the down right side of machine.Below the side door.Open it and then close it.Then bring out the tray and close it.Machine will start working.if not then tell me...