My business just purchased this copier last week, and we already got an error code that we have no idea what it means. It has a red light light ( status Light ) and it wont do anything but display error code C0211. What does this mean and can I fix it or do we have to wait for the repairman to finally get ahold of us later this week.
It means Bypass Lifting Motion Failure, check pick-up solenoid and lift up sensor.
Reboot machine holding down utility button, then do trouble reset, if nessesary reboot again.
If this error occurs again, you have to call for service
Posted on Dec 07, 2007
Hi and thank you for your help : I need to get access in to the TX fax settings but in order to do this I need to get the password in the administrator mode . Do you have this code ? thank you so much.
The default is "12345678" If it has been changed then you are outa luck eh.
Posted on Aug 05, 2008
I need the default IP address for the C350. Also how do I change it in the machine? And how can I find it if it was changed?
Press the Utility/Counter button.
Administrator Settings - password is 12345678
Network settings
TCP/IP settings
Posted on Feb 17, 2009
FTP tested ok SMB tested error "ED09C7"
Your configuration sharing SMB folder is incorrect. Create desktop folder rename all upper case SMB right click on the folder and click sharing and set full control to everyone. Go to web brouser type in the ip address of the printer log on to administrator password 8 zeros or 12345678 and change the setting.
Posted on Jul 09, 2009
Bizhub 350 error code c2557, how can i fix this?
This code happens if you replace drum without replacing developer. Both must be replaced at same time.
Posted on Oct 22, 2009
konika minolta bizhub 350 Error c3451
Hi there.
Try this It could do the trick for you.
The error code c3451 refers to a copier warm up error; the machine had not reached the correct temp within a specific time.
I bet it happened when you first switched on one morning.
Easy to reset and fault usually goes away.
To Reset switch machine off using the switch inside the front door, not the one on the control panel.
Whilst holding the UTILITY key down on the control panel switch the machine back on keeping the UTILITY key held down. Eventually a Trouble reset key will be displayed in the LCD screen, touch this, OK will be displayed then power the machine off and then back on.
This will reset the error code, if the code reoccurs then there will be a problem with the fuser unit in the machine, and this will require replacing.
Hope it did work for you.
Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks
Posted on Apr 28, 2010
how to find the MAC address for a konica minolta bizhub 350
I know this is and old post, but I came across this issue today and this post is the first that came up in my Google searches, and three was no good response. So I thought I would post an update.
[Sorry Zaheer, I know you were trying to be helpful, but your response was a little too vague and in the end, inaccurate]
1) Go to the printer's Web Connection by typing the IP address in a browser.
2) Make sure you are on the "System" tab (Blue) at the top
3) Click on the "Detail" link on the side menu
4) Click on the "Interface Info" sub link
* Notice that you do NOT log into the Admin portion of the Web Connection. That will only confuse you.
This will show various stats, one of which is the MAC Address of the machine.
It seems like this would be better placed in the Network tab under the admin interface, but here it is.
Hope this helps someone.
Posted on Nov 15, 2011
Konica Bizhub C350, need to setup ip address
Utility / Administrator settings (pass:12345678) / Network settings / TCP/IP settings. Select auto IP, or enter it manually. You can check IP address by printing Configuration Page: Utility / User Settings / Printer setting / Print Report / Configuration Page. Press start.
Good luck!
Posted on Dec 09, 2010
error code c0202
c0202 means that the top paper tray is not rising to bring the paper in contact with the feed rollers. Remove all of the paper from the tray and try turning the machine off and on with the paper tray not pushed in to the machine. Good luck.
Posted on May 20, 2011
C353 Tray 2 cannot be used curently That's the message and that's exactly what happens. Everything else works. No paper is taken from Tray 2.
First remove the paper from behind the draws, that is probably what cause the problem. Then you need to get into service mode. Utility/counter, details, stop 00 stop 01, password 9272927292729272, system one, trouble isolate,
Find the draw causing the issue then your going "SET" then power off WAIT TEN SECONDS power on then go though the entire procedure again get to the screen and select UNSET. Power off WAIT Ten seconds power on. Your draw should show back up.
Set
• "Unset" is Default
• After changing the setting, touch [Decision] and turn the main power switch OFF and ON to make the new setting effective.
If the not get a tech out to look at the problem
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
Posted on Nov 14, 2015
1,100 questions posted
Usually answered in minutes!
1,023 Questions
417 Questions
261 Questions
256 Questions
111 Questions
