A few days ago the error started occuring again. Whenever I try to scan to my SMB Box I get a Login Error and a Forward TX error. I get these two errors every time I try and scan now. Has anyone had this problem or know what the issue is? Thanks!
I had the same issue and fixed it by adding the group "Everyone" to the shared folder permissions (where I was sending my scans) and assigning the "Everyone" group rights to "change" and "read".
Posted on Jan 20, 2009
When I add the email address on the smtp scan to email settings it says invalid value. This is after I have pinged the email server address as well!
Server email address is correct and bizhub is on nw as I can connect to it via Mozilla.
Thanks
Allan
To scan to email, Administrator email address must be set in the machine (any bogus email address will work too).
Also, email server address must be input as IP address if DNS or WINS is not running in LAN.
Posted on Mar 09, 2008
can u pls advice how to fix this problem
thanx
Here’s your GEEK-steer …
This thread appears to cover the solution to your problem related to error "C5102: Main Motor’s failure to turn":
http://www.copytechnet.com/forums/konica-minolta/15515-c252-m1-operation-test.html
In addition, here’s the link to “Bizhub C250P” related support downloads:
http://kmbs.konicaminolta.us/content/support/supporthome.html
Hope this helps, and please post back with a status report and/or any further assistance you might need.
"Today's the best day of my life...and NOW you're part of it!"
Posted on Dec 16, 2008
My daughter was playing with buttons while something was printing. A page became stuck (which I have since pulled out) and now it it gives me the "Malfunction Detected - Contact your service representative C-2555). In trying to save $$ is there anything I can do myself to detect and correct the problem. I have tried powering off and turning the maching off as well. Your help is greatly appreciated.
C-2555 relates to a low toner density in the yellow imaging unit. I'm sure your daughter pressing buttons did not cause it.
I suggest you release the yellow imaging unit (the bottow row of units)
Just realease and pull it out a little way. Then switch the machine on with the door open. It won't start, but will ask you to shut the front door. Reseat the yellow imaging unit and shut the door. The machine should go in to a stabilization mode and then work.
However, if it comes back, I suspect a new yellow imaging unit will be required.
Posted on Feb 07, 2009
I forget my Admin password, have the Bizhub C252 Series, how do i reset my password to default? and what is the default password?
Try 12345678. That worked for me for my Bizhub C250.
Posted on Apr 02, 2009
How do I clear error message C-2558 for the Konica Minolta bizhub C253
tis error means abnormal tonder density in the balck image unit take the blacke image unit out and shake it while holding it level and put it back in the machine to reset the error code leave the machine on and open then close the front door
Posted on Nov 16, 2009
how to clear c-0204
C0204 - Tray 2 Elevator failure - The Lift-Up Sensor is not blocked even after the lapse of a given period of time after the lifting motion has been started.
1. Turn OFF the Main Power Switch.
2. Turn Main Power Switch
ON while pressing the Utility/Counter key.
3. Touch [Trouble
Reset].
4. Check to make sure that [OK] is displayed and the
it has been reset.
5. After turning off the Main Power
Switch, turn it on again more than 10 seconds after and check if the machine
starts correctly.
Reset your Toners and
Imaging units for Minolta Bizhub and CF series.
http://www.chipreset.eu
Posted on Nov 27, 2009
how to clear error code c 3421 on konica bizhub c253
C-3421 = Fusing heaters trouble
To Reset:
1. Turn OFF the main power switch.
2. Turn main power switch ON while pressing the Utility/Counter key.
3. Touch [Trouble Reset].
4. Check to make sure that [OK] is displayed and the it has been reset.
5. After turning off the main power switch, turn it on again more than 10 seconds after and check if the machine starts correctly.
If error code returns a technician is needed to replace fuser section. Call local dealer with error code and tell them to make sure a tech brings a fuser assembly.
Posted on May 19, 2010
Error code c0202. What is it mean? Konica-minolta bizhub c250
Most likely there is paper stuck in the very back behind one of the trays. Take both trays out and see if there is any paper jammed (could be a small piece). Put trays back in but leave them open, turn off the printer, unplug it, wait 5 minutes, plug it back in, turn it back on and push in the trays.
Posted on Dec 23, 2010
When a print job is sent to my Konica Minolta Bizhub c352, it only flashes "data" light, but nothing prints.
Hi Kenneth,
This can be a number of reasons.
When you go into the job list and look at the job history, Is there an error message saying "Deleted due to error" or something similar to this in there?
If it does, highlight the job and select "Details" to the lower right and please post what the "Error details" are.
Posted on Feb 20, 2014
1,254 questions posted
Usually answered in minutes!
924 Questions
417 Questions
261 Questions
256 Questions
111 Questions