20 Most Recent Konica Minolta bizhub C250 All-In-One Laser Printer - Page 4 Questions & Answers

Scan to what email or SMB (your computer) Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

code has to many letters/numbers will be C-XXXX Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

C2253: Color PC Drum Motor’s failure to turn

try to turn these IU's manually, and reset the error, sometimes helps, because usually motors works fine. also you may try to change IUs

Code

C5102

Description

Main motor malfunction - The main motor (M1) lock signal remains HIGH for a continuous 1-sec. a period at any time 1 sec. after the main motor has started turning.

Remedy

1 Check the connector between M1-PRCB CN6 for proper connection and correct as necessary. 2 Check M1 for correct drive coupling and correct as necessary. 3 M1 operation check. 4 Change PRCB. 5 Change DCPU. I’m happy to assist further over the phone at https://www.6ya.com/expert/latoya_8ed1bf3dc615c15d

Hello,

Check the ethernet cable. Using the cmd ping-t your copier ip adress and see if the printer comunicate with the network.
Here is a link with an example http://www.google.ro/search?q=ping+-to+ip+address&dcr=0&prmd=ivns&source=lnms&tbm=isch&sa=X&ved=0ahUKEwjf9dLlmLbYAhWdF8AKHc1NB20Q_AUIBigB#mhpiv=1&spf=1514790114761

C0211 Manual Tray Rise Descent Error
• The Bypass Lift-Up Sensor is not blocked even when the Tray 2 Vertical Transport Motor has turned for a given number of pulses after the sequence to move the Paper Lifting Plate from the standby position to the feed position was started.
• The Bypass Lift-Up Sensor is not unblocked even when the Tray 2 Vertical Transport Motor has turned for a given number of pulses after the sequence to move the Paper Lifting Plate from the feed position to the standby position was started.
This is a rank B error. To reset follow these steps:
Open and close the front door.
If error recurrs check the manual bypass again or call for service.

Please visit the site http://www.resetkit.eu
There you can find how to reset your fusing unit and transfer kit unit for almost all Konica Minolta MFP's and printers, Bizhub C252 included.
You don't need to replace it, you can just reset it and save a lot of money.

Reset your Toners and Imaging units for Minolta Bizhub and CF series.
http://www.chipreset.eu

C-2555 relates to a low toner density in the yellow imaging unit. I'm sure your daughter pressing buttons did not cause it.
I suggest you release the yellow imaging unit (the bottow row of units)
Just realease and pull it out a little way. Then switch the machine on with the door open. It won't start, but will ask you to shut the front door. Reseat the yellow imaging unit and shut the door. The machine should go in to a stabilization mode and then work.
However, if it comes back, I suspect a new yellow imaging unit will be required.

setting up auth. on mac requires that you open the doc on appropriate app, on print menu select output method, set auth. credentials, and save. then print. some mac OSX ver. will save others won't. prompting you to set auth, every time you need printing.

C-2452 When the developing motor/M
(M21) is ON, the maximum
detection value of TCR sensor/
M (TCRS/M) is the specified
value and the difference
between the maximum detection
value and the minimum
detection value is over the specified
value.

Estimated abnormal parts
Printer control board (PRCB)
Developing motor/C (M22)
TCR sensor/C (TCRS/C

Try a reset to factory defaults. Or a hard reset. Or driver reinstall. If nothing works then you have a physical issue with unit.

Something with your developer causing not enough toner. Maybe an auger issue in the developer or in the toner feed itself?

Left rear looking at the copier from the front. installed at a angle. one below is installed horiz. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Turn the machine off
Now press the stop button on the panel.
Now turn the machine ON.
Do not release the button until the machine reset and code is removes. Release the button when you see the code is removed and basic panel is shown.

This error also occurs after a paper jam or a steep power change. If error continues after doors were properly closed and the printer was turned off and on again, it'd be necessary to reset the printer and release it from trouble status.
Turn off the main switch (1/0 botton) but keep the control panel on. Wait 10 seconds. Press and hold Utility Counter botton on the Control Panel while turning on the main switch. Hold it until a white screen with a black dot over the upper rigth corner appears, then release it. Wait for a "trouble reset" botton on the control panel and then manually click on it. You'll see an arrow pointing to an "OK". Now turn off again the main switch, wait 10 seconds, and turn it on. Error must be gone.

NOTE • When Main-power was turned ON while the Serial No. was not entered (including initial status), the message to require entering the Serial No. will be displayed. Make sure to enter the Serial No. at setup. sound like some did not follow the set procedure. go to service mode and enter the machine serial make a mistake machine will be out of commission Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

whY?

First, I should ask where you buy your toner and what quality is it. If it's not a genuine Konica Minolta toner you will run into more problems.

Your first check, print using about 5 copies of card, if the prints on the cards shows shadowy image or you find shadow repetition of the prints, that's a confirmation of a bad toner quality.

This is due to a problem with Flash.

You can log out and then in again, but view the page as HTML and not as flash.

BTW if you re going to post the back door to your copier over the internet you may want to change the Admin password.

I have been able to log in a view properly.

pull out the color image units and shake each one along its axis to ensure developer and toner are equally along the image unit. then re-install if not have bad PC drum motor or worse the main board is gone$$$$$$$$$$$$$$$$$$$ Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f