Whirlpool Duet GHW9150P Front Load Washer - Answered Questions & Fixed issues
Washer somehow got into "control locked" mode and
Hello Shane, welcome to FixYa.
Based on your information posted..."control locked" mode and I do not know how to unlock it" ...this is a fairly common problem with these washers (including Whirlpool, Kitchen Aid, Maytag, Amana, (some)Kenmore to name a few built by Whirlpool) I hear about both on-line and doing on-site service.
The solution, however is usually pretty simple. As long as your washer is indeed the Whirlpool GHW9150 give this a try and let me know how it goes.
Press and hold the "END OF CYCLE /CYCLE SIGNAL" button as you count to 15...this will reset the control.
Good luck. Let me know how you make out as I said and if I can help you in any manner going forward I will do whatever I can.
Thank you for choosing FixYa. Please take a moment to rate the info provided here and a testimony on your experience here at FixYa today is appreciated.
Regards,
Macmarkus :)
Whirlpool duet washer sport ht - error codes
FYI: The pump cleanout is located on the front of the machine, bottom right corner. There are only three screws holding the bottom cover on. It is easy to get to if you prop it up a few inches off the ground. Just thought this would be helpful as I just did this as of 5 min ago. Should take 10 min. or less.
Pause mode stuck
Is the door firmly closed? Open the door and close it firmly. If the pause button is really stuck, you will need to repair/replace the board.
My duet dryer control lock
It is not related to moisture directly by any chance. If END OF CYCLE does not work. it can be short circuit inside which can cause this. Moisture can cause short circuit or the whole control board may be faulty.
Whirlpool duet washer won't start 3 dashes
It appears your timer/main controller/CCU has failed in this instance.
For replacement parts - head on over to PartSelect.com or RepairClinic.com and enter in your full model number for a full parts listing.
I recommend both sites because ...
FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.
PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.
If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.
Anything too complicated or beyond your scope should be handled by a professional.
If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question
F02 Washer not draining.
"F02" is a Long Drain error. If the drain time exceeds 8 minutes this error code will be displayed. In addition, a "SUDS" error may also be generated as a secondary error. This is an indication of a drain pump problem and/or clog in the drain line. You will need to check the following:
1. Check the drain hose to make sure it is not kinked or clogged.
2. Check the electrical connections to the pump and ensure the pump is running.
3. Remove the drain pump filter and check for foreign objects and/or debris.
To check the drain pump, click on the following link for step-by-step instructions.
http://www.fixya.com/support/r385844-checking_drain_pump_kenmore_elite_front
If the above procedures do not correct the problem, it is recommended by the manufacturer to replace the drain pump
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.&$&$&%&
Whirpool Duet - Soap not getting into wash cycle
O.K. Is the water draining out properly? If the filter is blocked then your washing will be churning in dirty water as the machine will drain for a maximum time then rinse etc. in the used water.
Fabric softener leaks out at beginning of wash
I have a 9200SQ Whirlpool duet. It might be similar. I think the bleach and fabric dispensers work on the siphon principal--once the level gets above a certain point they will then siphon out until almost nothing is left. They should not start to siphon until extra water is directed into them during the correct cycle. It is possible that they are starting to siphon early because 1. the washer is not level, 2. water is being added to the dispenser during the wrong cycle 3. You put too much liquid into the dispenser and it started the siphon.
Note: You should not peek in the dispenser during the washer cycles because it might interrupt the "siphon"action and leave residual bleach or fabric softener in the dispensers.
Laundry room smells like rotten eggs
Does the sewer drain line have a trap at the bottom that prevents sewer gas from entering the room? If the smell seems to be coming from the washer itself, run a wash cycle empty with a cup of baking soda, detergent and hot water to clean the interior.
F12 won't drain or
Hi, i'm pretty sure that this would seem to suggest that the pump maybe faulty or that there is a blockage, arm yourself with a large bucket or bowl and take the drain hose from the machine gently lowering it to below the washing machine tub level, make sure the drain hoseis quite flat or level as you do this, lift the hose if you need to stop the water because the bucket is full, empty the bucket and start again until no more water runs, then set about checking the filter for blockages or anything that maybe fouling the pump, if all is clear then it could be a suspect pump,if not clear all debris clean the filter re-insert it and make sure the drain hose is back in place, try the machine on a cycle,let it fill and see if it empties(pump runs), if not, the machine will not take in any further fresh water or do a main spin because there is water trapped in the machine. so you will have to go through the manual drain procedure again as above and try a new pump, there is also the possiblity it could be the main control board or faulty control loom.
If in doubt look for a washing machine technician that maybe able to give you a free quote.
Hope this helps.
I get an f06 and
F6
code is an issue with the motor drive tachometer.
Most often this is caused
by poor connections at the machine control or motor controller. Locate
the main machine control by removing the top panel and the motor control
by removing the rear panel. Remove each connector, one at time, and
reinstall. If this does not work, you likely have a faulty control.
E1
means that the thermistor is open and needs to be replaced.
The connections can be loose but the most likely cause of an E1 error is
a bad thermistor.
If you're comfortable and confident in your
do-it-yourself skills and have access to a volt/ohm meter you can check
and replace this part yourself.
For replacement parts - head on
over to SearsPartsDirect.com - PartSelect.com - or RepairClinic.com and
enter in your full model number for a full parts listing.
Hope helps.
My Whirlpool washer flashed F30. Not filling up with water.
Hi,
"F30" indicates "DISPENSER SYSTEM ERROR"
When the dispenser motor cannot be driven to its proper position this error appears in your washer. To fix this problem follow these procedures.
1. Unplug washer or disconnect power.
2. Check mechanical linkage from dispenser motor to the top of the dispenser.
3. Check wire harness connections to the dispenser motor and Central Control Unit (CCU).
4. Check dispenser motor for powered rotations.
Thank you !!
F20 machine won't stop
Whirlpool error code F20 appears when no water is detected entering the machine or if the pressure switch trip is not detected. The pressure switch is the part of the machine that monitors high water pressure. The washing machine automatically cancels the wash cycle during an F20 error. Wonder if it has additional issue since it won’t stop quality Appliance repair Stuart Internet answer.
Whirlpool front loading duet washer
Hello
Error F31 in your whirlpool duet washer is displayed due to MCU (Motor Control Unit) failure. It is displayed if the heat sink gets too hot and then the MCU stops motor, then MCU sends the signal to CCU (Central control unit). Please check the wire connections between the CCU and MCU, if thats fine then check the motor operation. Hope you understand...replacing the part# that has gone bad is recommended repair. Please get back to me if you have any other questions.
Kevin
We just purchased a Maytag Elite series washer
Cawnee:
Thank you for your review.
We would like to inquire further about your review with you. Please respond back to this email address,
[email protected], with your name, phone number, street address, zip code, model & serial number, and date of purchase on the appliance.
We look forward to your reply.
Thank you,
Maytag® Social Media Relations
What does FP mean?
Try looking online for another manual. Or call anyone who sells your machine. Me thinks the solution is simple, but you need to talk to any seller of your machine, and soon.
F 11
f-ll is too much soap
Not finding what you are looking for?