20 Most Recent Konica Minolta Bizhub C 353, Bizhub Color,bizhub C 253,konica,bizhub C 450,c 550 - Page 9 Questions & Answers

Hi Onyejekwe- I found this link. https://printcopy.info/?l=en&mod=erc&brand=Konica-Minolta&model=bizhub%20C25&code=0502 Hope this helps.

Sir/Mam, Turn off the main power switch, ensure the sub power switch is on. The sub power switch is located on the right side of the control panel. Then holding down the Utility/Counter button turn the main power switch on. Close the front door you must keep the Utility button down. The screen will show TROUBLE RESET touch it sees a "OK" then power off the machine. YOU MUST WAIT TEN SECONDS BEFORE POWERING UP AGAIN!!!!!! If the problem goes away OK. If the code comes back, you need a Fusing unit ( DO NOT KEEP TRYING TO RESET THE MACHINE! THE MACHINE IS TELLING YOU THERE IS A PROBLEM!!!!! A Fire could occur and that would ruin a perfectly good day!!!! Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

A search using https://www.google.com suggests the following:

• Code: C-2401
• Description:The erase lamp (EL) is unconnected.
• Causes:Erase lamp (EL)

https://printcopy.info/?l=en&mod=erc&brand=Konica-Minolta&model=bizhub%20601&code=C-2401 Web site above includes a link to a service manual.

Turn off the machine, remove the toner bottle, then power on with the bottle out let the machine do its start up procedure. one it asks for the toner bottle install it correctly

Bizhub C450 Manuals (english) https://www.konicaminolta.eu/eu-en/support/download-centre Error code list https://printcopy.info/?l=en&mod=erc&brand=Konica-Minolta&model=bizhub%20C450

• Code: C0211
• Description:Manual tray rise descent error • The bypass lift-up sensor is not blocked even when the tray 2 vertical transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the standby position to the feed position was started. • The bypass lift-up sensor is not unblocked even when the tray 2 vertical transport motor has turned for a given number of pulses after the sequence to move the paper lifting plate from the feed position to the standby position was started.
• Remedy:1 Check the M103 connector for proper connection and correct as necessary. 2 Check the connector of M103 for proper drive coupling and correct as necessary. 3 PC115 I/O check PWB-Z PJ7Z<A>-11 (ON) T to U-25 4 M103 operation check PWB-Z PJ5Z-5 to 8 T to U-22 5 Change PWB-Z.

Lo siento no tengo los recursos en espa?ol

Please the copier model exactly.

If you have lost the Bizhub manual you can find it here https://kmbs.konicaminolta.us/wps/wcm/connect/newweb/b6c3af14-17d2-40a0-9c96-de452ca7c836/bizhubHDDSecurityGuideC650_C353_751_501.pdf?MOD=AJPERES&CONVERT_TO=url&CACHEID=ROOTWORKSPACE.Z18_H0261AK0LG7QE0AE0BVQU730H1-b6c3af14-17d2-40a0-9c96-de452ca7c836-mJm5PTq

There is another cover at the down right side of machine.Below the side door.Open it and then close it.Then bring out the tray and close it.Machine will start working.if not then tell me...

You try cleaning and/or replacing the color registration assy?.. check the HV (high voltage board)..HV1 and HV2..

Yes

Push down Stop buttom and switch on.

The amount of toner in the developer is too high. service mode. adjust tcr +10

C0200 - Cyan PC Drum Charge Corona Malfunction. Did you mess with this imaging unit? You won't be able to reset if the malfunction is still present. --------------------------------------------------------------- Konica Minolta Error Codes & Solutions - http://www.kmcodes.com Drum, Transfer Belt and Fusing Unit Firmware Reset - http://www.bizhubreset.com Drum and Toner Chip Reset - http://www.chipreset.eu Transfer Belt and Fusing Unit Reset Kit - http://www.resetkit.eu

https://www.biz.konicaminolta.com/download/users-guide/c1100_c1085/contents/id12-_101518117.html https://www.scribd.com/doc/96776323/Top-10-Solutions-KONICA-MINOLTA

Self Help Product Support Konica Minolta Business Solutions Inc try this site Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

How to replace fusing unit in c253

What do you want to reset??? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

replace the drum cartridge, also clear maintenance counters in service mode Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f