U-Line Uline Origins Series Refrigerator/Ice Maker Manual Defrost-COMBO29A - Answered Questions & Fixed issues
No instructions for installing new seal on door
Service and parts manual is here.
http://stroboflash.com/searayproject/Docs/U%20LINE%20Service%20Manual.pdfThe procedure is as stated in solution 1 by expert Ironfist. The older units had a metal plate with screws that you had to loosed the screws in the retaining plate by peeling the gasket in the opposite direction without tearing it to loosen or tighten the screws on the retaining plate. Then you just lifted the gasket off. When you go to reinstall as previusly stated by the other expert... start in the top center and work to the corners. Make the coners fit before moving down either side to the bottom corners. Again make the lower corners fit and finally install the gasket across the bottom. Once installed rub the gasket mounting area smooth with one finger or thumb. You have humbled and hornored me with your request. If there is something that your really having difficulty with once you start this gasket change just repsond here and I will get back to you ASAP but, we will complete the task! Thanks again, Kelly
6/28/2011 2:40:00 AM •
U-Line Uline...
•
Answered
on Jun 28, 2011
•
497 views
I have an U-line combo 75A and the ice maker(part
few thing can happen, bad thermostat it caused the ice maker stuck in harvest cycle, short in ice maker defrost heater, bad water valve switch or the overflow hole drilled to low, it should be 1/4 inch below the top, I seen some of them drilled 1/2 inch below and it caused water leak.
3/2/2010 5:40:33 AM •
U-Line Uline...
•
Answered
on Mar 02, 2010
•
404 views
Wiring
wiring diagram is on the back of the machine. If you have clear ice maker it may be on the back of the front plate.
3/2/2010 5:33:15 AM •
U-Line Uline...
•
Answered
on Mar 02, 2010
•
350 views
Small refrigerator stopped working 75r
You have 2 wires. Unplug and put wires together. Plug unit back in and check to see if everything is running. Doesnt matter where the wires go with a 2 wire thermostat
10/13/2009 4:46:17 AM •
U-Line Uline...
•
Answered
on Oct 13, 2009
•
684 views
Uline icemaker on boat needs service..
first do a good cleaning as the manual describe.
check water supply and if still the problem, check power to cutter grid
should be 9 volts all the time
10/8/2009 3:47:14 AM •
U-Line Uline...
•
Answered
on Oct 08, 2009
•
293 views
My ice maker is pumping too much water into the
This will be the inlet water valve assembly. it seems to be malfunctioning. i recommend testing for proper functions. This could be a mechanical failure.
The water inlet valve is connected by two wires. Label the wire placement on the water inlet valve before disconnecting the wires. The wires are connected to the terminals with slip on connectors
Firmly pull the connectors off of the terminals (do not pull on the wire). You may need to use a pair of needle-nose pliers to remove the connectors. Inspect the connectors and the terminals for corrosion. If the connectors are corroded they should be replaced.
Inspect the filter screen where the supply line connects. Remove any debris or deposits that may have built up using a toothbrush
or warm running water. If you cannot clear the clog, it will be necessary to replace the valve (the filter is not removable on most inlet valves).
Test the water inlet valve for continuity using a multimeter. Set the multimeter to the ohms setting X100 (if available, otherwise use the nearest ohm setting). Place a probe on each terminal. The multimeter should display a reading of 200 to 500 ohms. Close inspection of the inlet valve and especially the coil may reveal the exact ohm resistance rating to test for. If the water inlet valve does not pass this test, it should be replaced.
8/6/2009 4:55:16 PM •
U-Line Uline...
•
Answered
on Aug 06, 2009
•
300 views
The bin arm on my Uline Model 402 ice maker broke
1st remove the icemaker from the unit. Then take the faceplate off.You might find that the support housing is fighting you.You should be able to move the arm into place as long as the icemaker is out.
6/29/2013 8:05:12 PM •
U-Line Uline...
•
Answered
on Jun 29, 2013
•
533 views
Ice maker keeps blowing relay
This could be a faulty relay or a bad compressor. If under 5 years old and your the original owner then call u-line for assistance. 800-779-2547
7/7/2009 3:13:04 PM •
U-Line Uline...
•
Answered
on Jul 07, 2009
•
221 views
My under counter Uline refrigerator/ice maker suddenly trips GFI
I here this alot. If you have a compressor on a gfi the compressor after awhile would trip it. The compressor start amps is usually higher than the gfi is rated. So you have 2 choices. Replace the GFI and try to find one with higher amp ratings. Or install a normal outlet for your unit. Your code will usually call for a gfi, If it does then replace with a new gfi.
To explain the start amps on a compressor depending on your model could be 10 amps. This is for a split second. However the gfi can become week after time. You can also try to plug the unit into a normal outlet to make sure everything is good on the unit. I believe it is the gfi
6/11/2009 2:59:28 AM •
U-Line Uline...
•
Answered
on Jun 11, 2009
•
634 views
Uline Icemaker has dammaged gasket door
no, you will need to replace the gasket. U-line gasket is easy to install. You can visit their website and under customer service you will see parts locator. The gasket just pulls out of the track and the new one pushes back in the track.
www.u-line.com
6/1/2009 3:35:32 PM •
U-Line Uline...
•
Answered
on Jun 01, 2009
•
593 views
The alert notification is from a u-line refrigerator and beeps even when door fully closed
Since you did not mention what make it is .
Its usually dirt in your door seal causing your refridgirator to understand its not closed since its not sealing properly . clean the door seals and try .
Or there is a technical glitch in electrical system and you need a repairman .
Also there is usually a way to disable the alarm and you need to check your user manual for that to disable it ill its fixed
6/1/2018 4:50:59 AM •
U-Line...
•
Answered
on Jun 01, 2018
•
2,908 views
Not finding what you are looking for?