Hotpoint Aquarius WF000 Front Load Washer - Answered Questions & Fixed issues
My washing machine wont start.
I have a hotpoint washing machine if I start the machine the water it's working after filling up the water the basket doesn't spin
12/29/2021 2:12:38 PM •
Hotpoint...
•
Answered
on Dec 29, 2021
•
241 views
Water still leaking
Look at and examine the door seal closely for any sign of a hole or tear in it.
If none is visible then it could be the clamp or spring that holds the seal to the drum front that is causing the prob..
Other than that , there could be a crack or hole in the container front.
9/19/2018 1:37:54 PM •
Hotpoint...
•
Answered
on Sep 19, 2018
•
148 views
Motor removal for WF000
undo the bolts and pull it forwards....removing the plug of wires....
cheers
3/10/2015 7:50:42 PM •
Hotpoint...
•
Answered
on Mar 10, 2015
•
79 views
How do I remove the clips from the pump
I found it easier to hold one part with a Pointy nosed pliers and push the plastic grip out the side of the clip.
As it is plastic it just ratchets back into place.
10/18/2014 11:05:50 PM •
Hotpoint...
•
Answered
on Oct 18, 2014
•
63 views
Hotpoint not drying clothes
Check the vent hose and the vent in the house for dryer lint. Excessive amounts will block airflow and the dryer senses that and shuts off the heat to prevent a fire.
10/15/2014 6:49:26 AM •
Hotpoint...
•
Answered
on Oct 15, 2014
•
70 views
My Wf000 door Locked is flashing, machine will not lock?
You can try this.
Switch off the washing machine at the mains, unplug it and leave it unplugged for about 5 minutes.
Plug it back in and see if it will work.
If it doesn't work you may need to buy a new door lock mechanism. The door lock has some electronics which can fail sometimes. You can buy the door lock on the internet for about twenty pounds and can do it yourself if you are fairly handy. There are also videos explaining how to do it on YouTube.
It worked for me.
Good luck
6/17/2014 2:35:31 PM •
Hotpoint...
•
Answered
on Jun 17, 2014
•
43 views
Leak from front
You take off the top to get into the machine, there are usually screws at rear top holding top panel on.
That said the most likely culprit is the pump which you get to from underneath, followed by the door seal, which you should inspect carefully for very small holes. My guess is the pump, have you checked the filter is clear?
5/16/2014 9:12:24 PM •
Hotpoint...
•
Answered
on May 16, 2014
•
32 views
Water not pumping out of machine-zanusi aquarius wf000
1. Check that the water tube is properly fixed
2. The tap is on
3. The program is on
If you hear a humm sound without water means that the valve is open but is closed before that.
If no humm is heard then the valve could be broken.
4/3/2014 7:18:47 AM •
Hotpoint...
•
Answered
on Apr 03, 2014
•
31 views
Aquarius wf541. Am trying to unscrew and remove
There must be something stuck in the filter, as normally it should pull straight out once you have unscrewed it.
Try screwing and unscrewing it at the same time keep twisting and pulling at the filter.
If you can't tremove it, then you sre going to have to remove the complete pump in order to clear the obstruction
Hope this helps you ..
3/22/2014 8:46:57 PM •
Hotpoint...
•
Answered
on Mar 22, 2014
•
719 views
Wf541 problems
if you mean the mains switch power this is available to buy on its own fairly easy to do,only four wires are connected to it.
11/7/2013 8:29:00 AM •
Hotpoint...
•
Answered
on Nov 07, 2013
•
72 views
Not finding what you are looking for?