Top 20 HP PSC 1315 All-In-One InkJet Printer Questions & Answers

It's not a printing problem ' it's your networking' try using the cable provided with your printer via usb' if it prints ok' then you need to reconfigure your printer settings' updates or clean re install.

This may happen because of overload to memory. If all are ok and still this error comes up means, the twain driver takes more time to load. wait for some seconds and then click scan, it will go. Try to clean the hard disk and defrag the drive.

Probably a cartridge issue. Get them cheap on ebay. eBayeBay

Printer will work .

hi go into control panel find printer settings u will have to clear any printing commands in c whats printing........good luck

For manuals in a range of languages including Portuguese go here HP PSC 1315 All in One Printer User guides if the language for this link does not come directly in Portuguese click on the down arrow symbol on the right of the 'select language' box and scroll up/down until you find it then click on the language on the menu 7.July.2015

Tri color cartridge contains Cyan,Magenta & Yellow color inks, mono cartridge contain black ink, combination/mixing with these inks desired color out put will prints on paper.. If any one or more inks are missing/dried, result mis matched print outs on paper. In your case I feel it's Magenta ink is not firing..,nozzles may clogged, try to clean the nozzles with solvents & try it...If no result ,. replace the color cartridge..

This is a more common occurrence than you might expect. The "door" referred to in the error message is actually the portion of your machine that must be lifted up in order to gain access to the ink cartridges for replacing them. You will notice that a protrusion on the lower side of the "door" surface fits into an opening in the surface below the door when the door closes, and this contacts with the door status switch to close the contacts on the switch, telling the machine that the "door" is closed. If indeed the door is fully closed, with nothing obstructing the switch from performing, then that would indicate that either the switch is defective or has come loose. After replacing cartridges, the "door" must be fully closed or you will see the error message. For troubleshooting procedures to solve this problem, go to this link: http://support.hp.com/us-en/document/c00829896 A test print page may show distorted characters at the beginning, but the characters should be shown correctly towards the end of the test page. If this is not the case then I would suspect that at least one of your cartridges is not seated properly. Open the cartridge access "door," and check the cartridge positions. When you remove and replace a cartridge, the new cartridge should be pushed back as far as it will go and then the front end of the cartridge lifted until you hear it snap into place. When seated properly, the top of the cartridge will be level.

It sounds as though a sheet of paper or an envelope bunched up and has jammed inside. Until that is removed from the feed roller, you will continue to hear the 'grinding' sound, and won't be able to print anything. Remove the cover from the backside of the machine, then locate and remove the obstruction. If you don't have any such obstruction then you have a mechanical defect which is not user repairable.

Open the front door, take cover behind the printer a little can shake up to something it's a pen

can you be more specific when you say the printer is off line. do you mean it cant read wireless access or is it that it is not set as default. make sure you have it as a default printer otherwise it wont be seen by the computer.

This page addresses what to do if you get different blinking lights on the printer. Match up the blinking light on this page with the light on your computer. Then click the plus sign to expand the page and view the solutions. The solutions for blinking cartridge light are not easily pasted here and I can't bookmark to that solution. Blinking Lights One thing to keep in mind with ink cartridge problems is that the cartridge has a warranty as well. You might consider checking back with HP using the warranty on your cartridge.

Throw this printer in garbage & buy a new 3 years warranty printer. I did the same thing. Please do not waste your very valuable time behind solving issues.

Hi, Which USB port Damage because there are two USB port available. One is Printer USB port or Sec is PC USB port. If you are say PC USB port not working first you check it USB driver installed or not, or USB connect to motherboard or not. PC there are two side USB available one is front side and sec is back side. You connect only back side, because this USB connect to main board. So you connect only back side. If not working removed driver or installed driver. Or if you are say printer USB then change cable or port or not solved only change option. Read More Help.. If you have USB or Network Printer and are having trouble printing and HP Tech Support

In the lower right corner of your computer screen, if there is an icon for the printer.......right click on it and see if it provides a checkmark option to put in online. Joe

If you allowed the device driver to auto-install in Windows 7 for example, only the printer driver will install and not the software required for scanning. You need to download and install the complete full feature software package. You need the AIO_CDB_NonNet_Full_Win_WW_130_141.exe file from the link below: HP Deskjet and Officejet Full Feature Software and Drivers

You may have one or more print jobs stuck in the printer queue. Download and use the free Stalled Printer Repair here... http://www.fantasticfreeware.com/?page_id=2451

HP PSC 1310 "hard reset" is easiest try: power on, wait until the power cycle completes. WITHOUT switching off, unplug power cord from printer. Wait approcimately 30 secs, plug back in and power on. This is a "dirty power up" and causes a reset that does NOT reset your settings. if that fails, try a FACTORY reset:

1. With the power on, disconnect the power cord from the rear of printer.
2. Wait 15 seconds.
3. Reconnect the power cord to the rear of the product.
4. When the lights begin to blink, press and hold both the On/Resume button (Power ) and the Paper Size button at the same time.
5. When only the On/Resume button (Power ) is blinking, release both buttons.
6. Wait until the On/Resume button (Power ). is steady.

Factory reset (settings wiped) is done. Try setting it up again. if all else fails, here is a guide that may help: http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/docDisplay/?spf_p.tpst=kbDocDisplay&spf_p.prp_kbDocDisplay=wsrp-navigationalState%3DdocId%253Demr_na-c00095908-36%257CdocLocale%253D%257CcalledBy%253D&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken Good luck!

This page explains how to solve that. Out of Paper Error Message Displays on the Computer and the Product...