20 Most Recent Konica Minolta Bizhub C552 Copier - Page 6 Questions & Answers


Sir,
Get to "Utility Menu screen"
Press the hard keys in the following order:
Stop ? 0 ? 0 ? Stop ? 0 ? 1
Touch the Soft switch tab in the first box on your left you will put a 3 in the middle box you will put a "1" the third box you will change the "1" to a "0". Close out to original screen and power off the machine. Wait 10 second power on should get your ready to copy, if the code does come back DO NOT RESET the machine again! It is indicating a problem the code you are resetting is the fuser and it can catch on fire! That will ruin a perfectly good day!!!

Konica Minolta... | Answered on Mar 03, 2019


Get to "Utility Menu screen"
Press the hard keys in the following order:
Stop ? 0 ? 0 ? Stop ? 0 ? 1
Touch the Soft switch tab in the first box on your left you will put a 3 in the middle box you will put a "1" the third box you will change the "1" to a "0". Close out to original screen and power off the machine. Wait 10 second power on should get your ready to copy, if the code does come back DO NOT RESET the machine again! It is indicating a problem the code you are resetting is the fuser and it can catch on fire! That will ruin a perfectly good day!!!

Konica Minolta... | Answered on Mar 03, 2019


Replace the hard drive

Konica Minolta... | Answered on Mar 03, 2019


reset the output tray to the proper position or might need the lift motor replaced

Konica Minolta... | Answered on Mar 03, 2019


raise the doc feeder and lever on the left side of the big glass to unlock

Konica Minolta... | Answered on Mar 03, 2019


yellow drum or sensor behind it

Konica Minolta... | Answered on Mar 03, 2019


Yellow drum or the sensor behind it

Konica Minolta... | Answered on Mar 03, 2019


In correct paper size setting if you use a4/a3 paper one setting if you use 81/2x11 or 11x17 different setting

Konica Minolta... | Answered on Mar 03, 2019


What model??? and that two codes ??? C-3451 and C0206?

Konica Minolta... | Answered on Mar 03, 2019


Did you install the proper drivers for the computer OS?

Go to KonicaMinolta Web site down load drivers (PROPER ONE) for your computers operating system they are free

Konica Minolta... | Answered on Mar 03, 2019


Clean the sensors under the transfer belt, replace the transfer belt, also run gradation prints outs to check each color and run gradation procedure

Konica Minolta... | Answered on Mar 03, 2019


Remove the drum unit then the drum and clean the sensor that monitors the drum. it will have a small with cover the clear cover sensor is for paper jams. be careful do not put your fingers on the drum if that does not fix it order the sensor conteol board the the sensor is mounted on

Konica Minolta... | Answered on Mar 02, 2019


Check the transfer roller assy and the transfer belt sensor cover

Konica Minolta... | Answered on Mar 02, 2019


Is the problem from adf?

Konica Minolta... | Answered on Mar 01, 2019


Use this function to initialize protect passcode and administrator's password.
1. Press <Mode>, <*>, <6>, <1>.
2. Press either [Initialize Protect Code] or [Initialize Admin Password].
3. Press [Yes].

Press <Mode> about two seconds until you hear the beep twice.
When you press " * ", you will hear short beeps.

Konica Minolta... | Answered on Mar 01, 2019

Not finding what you are looking for?
Konica Minolta Bizhub C552 Copier Logo

14 questions posted

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6850 Answers

Adorjani Laszlo

Level 3 Expert

1316 Answers

George Mclaughlin

Level 2 Expert

364 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Konica Minolta Office Equipment & Supplies

  • Konica Minolta Office Equipment & Supplies

Most Popular Question

konica minolta c552 error c3b02

  • Office Equipment & Supplies
Loading...