Top 20 HP Officejet Pro 8600 Questions & Answers

Re Istall driver

left click start menu left bottom corner of desktop find all programs listing Look for a program called hpscan https://h30434.www3.hp.com/t5/Scanning-Faxing-and-Copying/HP-Officejet-8600-Pro-how-to-change-scan-resolution-presets/td-p/2721003

https://advodka.com/keyword/hp%20officejet%20pro%20k8600%20service%20manual?region=spb&engine=google Visit this site to download the repair manual to this device. it will have its schematic. http://electronicshelponline.blogspot.com/

Make a copy of both sides then fax them separartly

Check all the settings that regulate the fax, pay close attention to the speed settings.

HP is making "disposable" printers. They have "repair kits" available but to repair a printer you need some quite advanced knowledge and practice so my best advice is that you should take it to an authorized HP service

get a label print software

You can get it from HP's web page. HP Support Software and Driver Downloads

remove the paper draw,then open the back panel [should just flip open] check for jammed paper,reload paper draw with at least 1/4 inch of new paper,put back in,and retry printing.If theres still a problem,the printer usually tells you.Recheck yr printing settings

Open up the Panel It has the writing HP office jet pro Etc. on it, then the cartridge/head will move toward you, push in on the yellow cartridge until it clicks and release it will disengage and you can remove old cartridge. Installation is exactly like removal insert new cartridge until it clicks release and it will engage. Close panel and the cartridge/head will move back to previous position

Select "Copy" from the touchscreen and then select "Settings..." Adjust the "Lighter/Darker" setting and see if that helps.

You have to follow this steps: 1. Load paper in the tray. 2. On the File menu in your software application, click Print. 3. Make sure the printer you want to use is selected. 4. To change settings, click the button that opens the Properties dialog box. Depending on your software application, this button might be called Properties, Options, Printer Setup, Printer, or Preferences. 5. Change the paper orientation on the Layout tab, and paper source, media type, paper size, and quality settings on the Paper/Quality tab. To print in black and white, click the Advanced button, and then change the Print in Grayscale option. 6. Click OK. 7. Click Print or OK to begin printing

Dear Pl. check the ADF cover locked at both side. Clean the pick up roller with dampen cloth. Thanks.

Hi, first look up on Google what dos error 386 stands for on the printer, than you can go from there...!

have you tested the power supply? (small black box attached to cable , sometimes clips into printer ) try changing it out

Dear You can customize the setting to scan area and resolution of scan. Try to use the application provided by the manufacture. Thanks.

Dear Go for replacement with new one, also check the base contact points of the holder if possible clean with lint free cloth dampen with isopropyle alcohol while printer is power OFF. Thanks.

Are you asking where to open the unit to get the ink containers and print head accessible to replace the cartridges? Or are you trying to figure out how to fill a cartridge with aftermarket ink? To replace the cartridges themselves you must have unit on and on the left side where it says HP Office jet Pro etc. is actually the cover to the ink/head area open that and the head will automatically move over and allow access to the ink cartridges and the print head. To remove a cartridge just push in on it and it will click and disconnect. To install just push all the way in like removing until it clicks and attaches. As far as adding aftermarket ink, I am not sure that is advised as I know I used to do this until last time it ruined my print head and made a mess as it leaked out of head unit all over inside of printer which in turn leaked onto desk and then onto floor. But if you think it would be ok the specific instructions should be included with the refill kits as different cartridges have different areas needed drilling etc. to access ink well/tank. Hopefully this helps.

Have a good Day

If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/ Type in the brand name of your device, in the search box [at the top right] of the display window, and press enter to get all related posts. It will make surf easy.