U-Line 75WC Wine Cooler - Answered Questions & Fixed issues

Question edited for clarity, maker. Question moved from Watches to U-Line Wine Fridge. They are usually an expanding plug. You push it to the hole and press the central pin. If you can grip it with pliers, you can pull it out. The other way is to use a nail punch and push the pin all the way through, pull out the support and retrieve the pin from the insulated cavity. https://www.amazon.ca/s?k=U-Line+wine+fridge+shelf+support&i=tools&crid=6P110ETE4YHD&sprefix=u-line+wine+fridge+shelf+support%2Ctools%2C69&ref=nb_sb_noss https://www.google.com/search?q=u-line+wine+fridge+shelf+supports ..

If you visit U-line at www.u-line.com and under customer service you will see parts locator. You should find a distributor to help you with that.

Usually if you see frost or ice it is because the Freon level is low. There is a 5 year warranty on the compressor and sealed cooling system so if your within that period, I would call the manufacturer.

Sorry if for your memory problems but I have no way to help you. Discuss this matter with the provider of your Wine Cooler

Cheak The Compressor relay is fault

Does the compressor vibrabte? If not, the PCB isn't working and should be replaced or worst case is your compressor burned out.

fAN MOTOR MAY NEED REPLACED. THE EASIEST WAY IS TO TAKE OFF THE BACK PANEL IN FREEZER AND REMOVE THE FAN
MOTOR, TAKE IT TO THE NEAREST APPLIANCE PARTS STORE WITH YOUR MODEL NO.
EASY JOB.
I'm including my article on Refrigerator Repair for your help and convenience.;
Please click or copy and paste into browser for Article

http://www.fixya.com/support/r5816737-fix_refrigerator_psychologically
If you need more help go here:

http://www.applianceaid.com/procedures.html

MORE TIPS AND TRICKS:
-----------------------------------------------------------------------------------------------------
STOP PAYING FOR EXPENSIVE WATER FILTERS FOR YOUR REF. DO THIS====
http://www.fixya.com/support/r9962087-stop_paying_high_price_refrigerator
-------------------------------------------------------------------------------------------------------
WATER SPLASHING IN FREEZER AT ICEMAKER
THE FILL TUBE IN BACK OF REFRIGERATOR CAN SLIP
AGAINST THE FILL RESERVOIR CAUSING A PARTIAL BLOCKAGE
OR BECOME CLOGGED WITH ICE.
REMOVE THE ICEMAKER AND INSPECT THE FILL TUBE.
RUN WATER IN TUBE TO ELININATE BLOCKAGE AND CHECK
TEMP IN FREEZER. IF TEMP IS BELOW 0 DEGREES, THATS
OVERKILL AND USUALLY A WASTE OF ELECTRICITY TO KEEP IT THAT COLD, NOT TO MENTION THE FILL TUBE FREEZING UP
----------------------------------------------------------------------------------------------------------------------
Thanks for using fixya
Leo Ponder
imufo2
Please VOTE FOR ME AND GIVE ME YOUR TESTIMONIAL IF POSSIBLE, IF THIS WAS HELPFUL
ITWILL BE MUCH APPRECIATED.

Hello,
The U-Line OEM part # is 2767-S it should be available at your local applaince parts store or online at;
apdepot.com
searspatsdirect.com
repairclinic.com
apwagner.com
appliancepartscenter.com

Gene

No more than five PSI and no less on the low side If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

if compressor working it need for flushing and cleaning of intire piping system or reprocess system replace filter drier brazing and recharging of exact amount of refrigerant.

the new one goes in the same as the old one comes out. You have 2 screws on the bottom of the evaporator that holds the sensor in place. Then the sensor runs thru the bottom toward the back.As you remove the old one jus put the new one in the same way.
This is actually the easy part....;-) On mine... I had to remove all of the shelves (5) which slid out just like my kitchen cabinet drawers. Next I removed 4 screws that held on the cooling coil assembly (Big white smooth flat piece with raised ridges running through it.). Once the screws were removed, I carefully lifted the cooling coil assembly/panel until I could see the old whip and pig tail. (Sorry I am going on memory here...) I believe that there was another screw that held the end in place that I had to remove and then reattach to the new whip once inserted through the back and snaked into place. Really I remember this taking only about 10 minutes to do start to finish. I reused all of the "filler" stuff to reseal the new whip in place.

The wires on the thermostat doesnt matter. 1 wire on each terminal would work. Its just a switch

the odds are your door gasket is leaking.

Good Luck,
Gilsh

Only by replacing the door. You can visit www.u-line.com and under customer service you will see parts locator.

To order the racks you will need to order from a parts distributor. To find one in your location just visit U-line. www.u-line.com and under customer service you will see parts locator.

Check the thermostat to make sure its mounted on the evaporator plate. If its away then the sensor will never satisfy your control, Or you may need to replace the control

No pictures, the new one goes in the same as the old one comes out. You have 2 screws on the bottom of the evaporator that holds the sensor in place. Then the sensor runs thru the bottom toward the back.As you remove the old one jus put the new one in the same way.

You have either a week connection or a bad thermostat. Check your connections. Part # 2767-s

If the sensor of the thermostat is not on the evaporator plate then yes the thermostat will never be satisfied. Because it is not reading air temp only the evaporator plates temp. should be clamped onto the bottom of plate.

If this model has a mechanical thermostat then that is your problem. If its digital then it could be something else. Posible just by unplugging the unit could reset the board.