Philips Magnavox 27MS343S 27" TV - Answered Questions & Fixed issues
Magnovox squiggly lines when cable is plugged in.
If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/
Faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault to an extent.
View the site by desktop or web view on mobile devices to see the "search box". Type in the brand name of your set in search box; to get gathered the related posts...
Magnavox XP 2390 B101
Press the Vol up and down buttons on tv until it turns off than turn the tv on just like the photo.
Dvd freezes
If less than a year old, this TV is likely under warranty but should have been taken back immediately to address the issue. I suggest contacting the vendor or manufacturer.
My sound stopped working on my tv
It might be that the sound amplifer is defective if you know anything about electronic you can fix it . If not better take it to someone who can repair it.
The amplifer is the part of electronic that amplifies current so the speekers can be driven. Check it if there is a bad solder or anyhing suspicious.
Magnavox 25TS52
If its a LCD set not plasma I would look at the connectors going in and out of the Tcon board, remove them and reseat them, if that doesn't help replace the board.
There is one other thing you can try and that is remove the board and put it in your oven at I think its 370 degrees for 10 minutes, Ive never tried doing this but there are some vids on people having good luck doing this, what happens is there are some cold solder joints on the components and putting it in the over will heat them up and the board will work again, search this on youtube and there are vids on how to do it.
Tv working fine, then suddenly,pop and black screen, sound is ok
The issue here is that the zeners in question are merely like a safety fuse and replacing them before identifying and fixing the cause of the problem will only cause your replacement zeners to blow aswell.... personally if it is a true plasma it likely chews through alot of power anyway so I would take the opertunity to replace the TV with a newer much less power hungry led TV and in doing so save the hip pocket and the environment.
Child lock
hi.... i did child lock my tv magnavox and can't turn on ,,,because my remote control is broke now.. so tell me please how could turn on my tv Please Tanks...
I need a cord I need for an observation cam from magnavox
Strange, I have the opposite problem, I have the cord and camera, but no monitor. I found the following fix below to make this camera hook up to any tv or monitor, but it's greek to me. It may help you though! Or, if you can translate these instructions for me to hook up mine, I'l happily GIVE you my cord!
"The DC power was sent up the coax and the video is AC coupled and sent back down. If you open the
camera and trace the wire from the center pin of the UHF connector, it will lead to an inductor
and a large value capacitor. The video is coupled through the capacitor, which blocked the DC
power from the video output amp. The inductor (coil) blocks the video from getting back into the
power section.
Cut the inductor loose from the center wire of the connector. Put well filtered +12 VDC at 500
mA (1/2 amp) or greater into the inductor at this point while running a video cable from the jack
to a video monitor or to the video input of your home VCR. Then you can see the video on your TV.
Power return is to the ground of the connector or any other convenient grounding node.
4 diget code for magnavox model M27MS343S
Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. One among it has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily.
http://remotesearch.blogspot.com/
http://electronicshelponline.blogspot.com/
http://electrohelponline.blogspot.com/
Search the site by type in the brand name of your device, in the "Search box at the top right of the Home page display" to see the set-up codes to your device, with different brand remote controls.
Not finding what you are looking for?