Toshiba 36A50 36" TV - Answered Questions & Fixed issues
Rca 27v412t tv picture only in middle of sceen
It is the fault with some components related with its horizontal scan output section circuit. Just check the circuit part; and check the components I've marked in red here by its horizontal scan output circuit. Beware; you're going to touch the most dangerous part of its circuit. Keep it in mind always.
If you wish to see the circuit diagram in full; visit
http://schematicscom.blogspot.com/
Codes to samsung tv
038,017,082,053,091 are the codes to check. If you wish to get more details,
check this site.
Pull up previous posts there. Setup code list and setup proceedings to
many popular brand remote controls are given.
Three digit, four digit, five digits and two-digit code list are there. Check the site with patience. Surely you'll get a solution to your problem. Search the site by 'Timeslide' option. It will make search easy. Or, type in the brand name to your device
into its search box, and press "Enter"
Toshiba 36A50 Horizontal Line
Ok, The vertical Ic is IC301 Ta8427K And Capacitors around IC chroma 2.2 uf 50 volts. You will see small red capacitor ( with C302....4 or 5 ) reference. Replaced others capacitors on vertical section 220 uf 35 V or 100uf 35V. I hope this can help you. Or if do you have any picture chasis, send to me and I will show you where are the problem., Thank you
1 vertical line across the screen maybe 1" tall.
tv turns its self off i unplug it plug it back in it will flash on not showing picture it u can her it flash on and right back of some times it will not flash in back of tv and i can hit power it will flash and go off every now and then it will come on show picture after being unplugged and plugged back but then shuts off
I have a Toshiba 36A50
hi,
Hi check is there is any dry soldering in the vertical scanning stage or in the power supply stage. of your tv. If the soldering of the vertical ic is dry( improper spldering contact coused by years of use) then this can happen.Thats why it disappears some time when there is a proper contact comes. You can confirm is it dry soldering by shaking the tv while its working. If the line comes and go off then there is dry soldering in the vertical scanning section. To rectify this you have to oppen your tv And have to resolder the points in the vertical section. Have added the picture, how a dry soldering point looks.
ok
Lost remote. Must do manually on t.v. Two
Try website like Remotes.com to buy the tv original remote to used.U will used the tv original remote to turn to channel 3 with ease.After u have the tv original remote push the menu button go into Closed Captioning functions turn off like TEXT 1,2,3...The big black box will not appear on the screen again.Tv used it manually control buttons up and down channels trying to get to channel 3.U will never get it to tv channel 3 because tv channel 3 was not save on it memory list of on the tv turn manually channels buttons programming memory.Tv have a manual button said MEMU button on it tv front bazel frame?Yes.Might could used the Menu button on the tv frame to get in to turn off TEXT 1,2,3...to stop the big black box to show up on the tv screen again.
Half the picture is faulty
Maybe the problem of your television is loose PCB connection, ethier it is cold solder.It is need to resolder first then if did not work.It is time to replace a leak capacitor at vertical section of the crt board.
Toshiba, 36A50 picture is a thin white line. Can
Yes...this TV may be repaired. The line you describe is in the center and is horizontal across the TV. You will need to resolder the vertical IC pins. This vertical IC is mounted on a large heatsink. Under the board you will see there are 5 or 7 pins that will have rings around them. Resolder these. And you should replace two or three capacitors that are next to this IC. A bad cap will overheat an IC and separate the solder grounds. If you can find my expertise page on this website, you will see the repair in more detail. Thanks for asking and show a few hands of support.
ANY HELP ON A JVC
Sure I can. If you can just tell me what the problem is, I will be glad to help you :)
Toshiba 36A50 no longer responds to remote
The only common problem would be on the Toshiba Remote. Make sure you have the switch on the remote set to "TV' and not Audio, or Video. Beyond that, if you have a digital camera or a cell phone with a camera with a viewing display, point the remote at the camera and push any button. If it is sending IR, you will see the flashing from the remote on your camera/phone display.That will just confirm the remote is sending signals. The only other possibility is that your IR receiver on the TV is bad, This happens, but it's not very common. Hope this helps
I need a code to make my time warner remote
According to timewarnercable.com, the codes for a toshiba tv are 074, 168, or 170.
If none of these codes work, I suggest you try the code search function. To do this, follow the steps listed below.
1. Turn on the tv
2. Press "select" and "tv" together until the LED blinks twice.
3. Using the keypad on the remote, type in the digits 9-9-1. This will open the "code library." The LED should blink twice.
4. Press "power."
5. Press "channel up" key repeatedly until the tv switches off.
6. When the tv turns off, press "tv" on the remote to lock in the code.
Your remote should now be programed to your tv.
I hope this helps, and good luck!
Sincerely,
Der Strom
The 36A50 t.v.that i owned for 8yrs.started with
This is an easy repair if you've ever soldered and would not be too costly for a repair shop to do it for you. The problem is a bad Vertical Output IC (usually mounted on an aluminum heat sink with the part on it labeled LA78?? or AN?? ) and 1 or 2 bad capacitors. Some times you can even fix the problem by re-soldering the contacts of the IC- To find the IC follow the 4 wires that come from the Yoke (which is a contained coil of wires slipped over the neck of the picture tube(s)) back to the board. 2 of the wires go to the horizontal o/p and 2 to the Vertical o/p the thinner gauge wires are for the vertical. Be sure to vote/rate me if this helped Thanks!
Where is the la78 located on the tv and where is
bad Vertical Output IC (usually mounted on an aluminum heat sink with the part on it labeled LA78?? or AN?? ) and 1 or 2 bad capacitors. To find the IC follow the 4 wires that come from the Yoke (which is a contained coil of wires slipped over the neck of the picture tube(s)) back to the board. 2 of the wires go to the horizontal o/p and 2 to the Vertical o/p circuit area. the thinner gauge wires are for the vertical.
On our tv screen is a big black square on the
It sounds like the set has been put into the text mode. This setting is in the CC or closed caption section of the menu. You should be able to access this with the menu button on the front of the set. Turn it off when you get to that section of the menu. This black box is where the "text" for CC would normally be written if your cable service provided it. Thanks
Blinking red light
this is a dry canaction problum in pcb do not slap tv.
* cont. tv tech. nr. at your home solve this problum in fuw mint. it is not expanciv but. if you slap tv then posibal spear damage in inside tv.set.and he is very expanciv.
Not finding what you are looking for?