I am having the same problem with the red lines not aligning when doing the convergence procedure. When watching TV their is an awful red hue or shadow on the screen. This is the post that I have questions about: "Order online part # SSB-5068A. This is the ENTIRE convergence board with new IC's. Cost you about $140 (from vance baldwin.com) but is a lot less hassle than you trying to soldering/desoldering parts. Only thing is, next to the 2 large heat sinks, there is this large silver component that you need to unscrew from your old board, and unplug and attach to your new board." 1. The baldwin link... http://www.vancebaldwin.com/products/?SSB-5068A-M2-R&t=P * it has a different part number than the ssb-5068A, the link shows SSB-5068a-M2-R. Is this the same part? If not, I am not able to locate the part. 2. What does the convergence board look like behind the tv?
I just removed both of my 110 IC's and replaced them with 150's. However in the process of removing the solder from the old board, I may have damaged the pads/vias where the pins make contact. Be careful of this when removing solder. I also blew 5 resistors after plugging in the new IC's.
Posted on Aug 05, 2007
I have a JVC rear projection tv model AV56WP74. A couple of weeks ago all three colors went out of wack but I was able to align them again. Then a week later the green line at the top left habd corner curved down and I was not able to fix it. Now the convergence is all out on all three colors but especially the green which is curving. Is this expensive to fix or am I better off with a new t.v?
change the green lamp
Posted on Sep 18, 2007
A few weeks ago the convergence on my JVC 56" rear projection t.v. went out. I was able to realign it. A week later the green convergence on the top left hand corner started to curve downward and I was not able to align it. Now all three colors are not aligned but especially the green which is curving and I am not able to put them back. Is this expensive to fix or am I better off with a new t.v?
Here are some of the most common symptoms and example photos of a convergence problem
Here is a quick test....
Using your original remote go-to the tv settings then goto the convergence section.
Try to adjust the red and then the blue convergence.
You should be able to move them up, down, left, and right.
If you can't move them in all directions your convergence chips are bad and should be replaced. This is a common problem. 
Solution #1
You need to replace the convergence chips and convergence resistors. Check the site www.TvRepairKits.com. They have put together a kits for most models. If you don't see a kit for your set send them a quick note and they will put one together for you. Their kits include a photo instruction guide, original OEM Sanyo STK chips, convergence resistors, pico fuses, etc.
Posted on Mar 21, 2009
IM GETTING DOUBLE PICTURES (GHOSTS) ON THE SCREEN. MY CONVERGENCE IS OFF AND I CANT ADJUST IT BACK IN
You will need to replace the convergence iCs there are two of them they are both STK392-110 Ics you will also need the JVC convergence resistor kit. You can get the ICs and resistor kit at the following link and they provide free instalation instructions with pictures. Heres the link.
http://servicemanuals.vstore.ca/
Posted on Jul 27, 2008
My TV's convergence went out and I'm ready to fix it but I need some assistance. What IC's do I need to replace along with which resistors? I need to know part numbers to order.
(2) STK392-110 Convergence Amp ICs
(3) 220 ohm 2watt metal film resistors
(3) 150 ohm 2watt metal film resistors
(2) 1.5 ohm 1watt metal resistors
(2) 2.2 ohm 1watt metal film resistors
(1) 1.8 ohm 1watt metal film resistor
(1) 3.3ohm 1watt metal film resistor
You can get the entire convergence repair kit which contains all the parts listed at the following link its called the AV48WP30 Convergence repair kit , but it applies to your model as well, and they include free installation instructions.
http://servicemanuals.vstore.ca/
Posted on Aug 23, 2008
Hello,
I was searching online about what could be the problem with our TV and I came across your page. We have a 52" JVC Projection TV that now has a "blurred" screen. We can see the channels but it looks like it's has a shadow around the images. The screen in in a red hue with green blur.
If you have any suggestions on what caused this and what we can do to have this fixed, I would greatly appreciate your advice.
I was searching online about what could be the problem with our TV and I came across your page. We have a 52" JVC Projection TV that now has a "blurred" screen. We can see the channels but it looks like it's has a shadow around the images. The screen in in a red hue with green blur.
If you have any suggestions on what caused this and what we can do to have this fixed, I would greatly appreciate your advice.
Posted on Nov 05, 2008
need a circuit schematic diagram for Bush LCD TV board is 04TA0691
Hi
I have a .pdf of the diagram - can you let me know your email so I can send it - it's too big to attach.
Glyn
Posted on Oct 31, 2008
I have a jvc i art pro 56 inch projection tv and when i plug in the tv the tv makes a clicking like noise and the speakers make a popping noise and no picture displays and the green light just flashes. can anybody please assist me i can not afford another $450 for repairing my tv
The clicking sound is the TV trying to restart itself. It generally attempts this several times before giving up. The blinking code indicates the type of error (error codes are documented in the manual for the TV). The most likely cause is a burned out bulb, but could be something else.
If it is a bulb, it is usually replaceable without a service technician, and at a cost far less than $450.
Good luck.
Posted on Jun 18, 2009
I have a JVC AV-56Wp74 Blue power light on the front keeps blinking and the screen is black & makes a popping sound
There are a couple of common problems this model has--one is easy to confirm.
How handy are you if I tell you to disconnect the convergence board to see if it is your problem?
The blinking blue light means the set is in protective shutdown, and I know a fairly easy way to see if it is your problem and how to fix the set if it is.
Let me know if you need help--I am here to help people and l know a lot about this set.
SD TECH
Posted on Dec 16, 2009
what would cause my jvc tv have a green tint
It sounds like you can have optical engine issue. That's if green tint was show up very gradually, until one day it really caught your attention.Normally some parts of the screen more green than other. It should get progressively worse. To solve this issue optical engine have to be replaced. It is pretty expensive repair if your TV is out of the warranty.
In case if tint appeared suddenly in one moment - you can try to check component cable connection on the back of your TV if you are using one ( green, blue and red colored). Sometimes it's loose or after disconnection people reconnecting it in wrong way.
Experienced tech will determine if optical engine is bad by running test patterns in special service mode. If green tint present on Grey scale - optical engine is bad.
Sorry for bad news.
Regards.
Russ.
Posted on Apr 06, 2010
381 questions posted
Usually answered in minutes!
443 Questions
208 Questions
175 Questions
149 Questions
147 Questions
