20 Most Recent
JVC AV-56WP74 56" Rear Projection HDTV-Ready Television - Page 4 Questions & Answers
Words outlined with red
See attached photos, this board is from a set just like yours. The two black ICs with the STK392-110 MARKED on the front of them will need to be replaced and the resistors in front of them inspected to see if any are burnt/discolored.
This is a fairly easy set to do this on, total parts cost on Ebay would be under 25 dollars.
The best way in this set is to remove the board, access will be from front of set.
I can tell you what is involved to get at the board and remove it. It does involve soldering as each of the two chips has 18 pins.
Look at the photos and let me know if you have questions or need advice.
SD TECH
Picture went out and the tv comes on but no
If it's failing to turn on, the main power supply is probably at
fault and without some technical background and a couple of test instruments,
you will not be able to do the repair yourself.
What you can do though is; unplug the set, let it
stand overnight or at least several hours, remove the back panel and look for a
separate board with mostly larger components on it; it will have a ferrite core
(no laminations as with a line-frequency part) transformer on it and several
larger capacitors which are cylindrical and mounted vertically to the board.
Before touching anything inside, especially on
that board, allow several hours to be safe since the larger capacitors can hold
a painful voltage charge for some hours.
If you see signs of overheating such as
discoloration of the board material, the PSU may not be repairable but if you
can find a part number on the board, you might be able to buy the power supply
from the mfr. and install it yourself but it will likely have the same problem
eventually unless they have altered the design or improved component quality.
If there are no signs of heat damage to the board,
there may be companies offering to repair it as a subassembly instead of
repairing the whole set which could be much more expensive.
If you choose to replace or have it done, the main
power supply still may not be at fault since most are capable
of switching off if a downstream problem is causing an overload .
Convergence is out...trying to manually adjust but
Tv have 100% convergence problems,it dead.The tv have colors lines R,G,B mis alignments,have colors pictures shadows or 3D pictures look alike?The tv convergence board have dead 2 STK convergence ICS and some or all of it resistors too.These parts on the tv convergence,must be replaced to solved the tv pictures convergence problems.The shop,will cost u like $300-350 for parts and labors.
I am unsure which model
Hi,
From the information you have provided the problem is with the
convergence. If you have gone into the menu and tried adjusting the
focus/conversion after the TV has been on for an hour or more and the
focus did not correct the problem the convergence ICs have failed and
will need to be replaced along with a few defective resistors. If all
the colors are incorrect a open fuse in the voltage supply to the
amplifiers is possible. A TV repair company will normally charge about
$350 for this repair if the ICs are the problem, less for the fuses.
Small TV repair shops will normally charge less than large repair
facilities. Convergence failure is a very common problem with this TV
set. There could be other parts that are not within factory specs. The
only way to be positive of the problem is to have the circuitry
diagnosed by someone with the proper TV test equipment to determine what
parts that are no longer within specs. A small TV repair shop will many
times be less expensive than a large repair facility.
If you wish to repair it yourself and can solder, I will suggest that you
to purchase a kit that has all the needed parts and detailed
instructions for making the needed repair from :-
.When you get to the site
using the link provided, choose TV repair kits, enter in the model
number for your TV and select convergence repair kit.
I am sorry, you need to confirm the model number. There should be model number engrossed, might be back of the TV .
Let me know,if needed further assistance.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!
My AV-56WP74 unit the blue
chrisiensen1,
You have most likely lost one or both of your convergence ICs. The ICs are not too hard to replace if you can use a soldering iron and are concientious. If you think that you are up to the task I have a tip at
http://www.fixya.com/support/r4220499-change_projection_tv_convergence_ics which explains the problem, walks you through the repair and has links to the best place to get parts at the best price.
Thanks for using FixYa and for the great rating.
hardrocko
Tv comes own and popes
there some problem with your power supply.there is some drive ic,fet or ic link problem.
check voltages if there some of missing which is menstion on board .then use to check same line you must find out problem.
TV TURNED OFF WHILE WATCHING.
If you are talking about the blue power light I have a good idea and a way for you to find out.
See attached photos--they are of this set's CONVERGENCE output board--it is located behind the front grill and I can tell you how to get at it.
What I usually do in this case is get at the board and unplug selected plugs (it has 5 or 6 of them) and then turn set on.
Surprise? set comes on but looks terrible----it means a short on the Convergence board is causing the set to shut down.
Look at photos and tell me if I can help you.
SD TECH
Where can i get the
You do not need a diagram, I can tell you all that is involved--it entails getting the board with the parts out and replacing both chips and any bad resisters.
See attached photos: they are of the board that needs to be removed.
This is a easy set to get at the parts and they are soldered in, so you need to be able to solder etc.
Let me know and I will be happy to assist here.
IF the pictures or this information told you something you did not know rate this solution as very helpful as I do this here for free.
SD TECH.
I HAVE A 48 JVC
Thats caused by failed convergence ICs and resistors. You can get the JVC AV48wp74 -AV65WP74 cnvergence repair kit from <A href="http://www.tvrepairworld.com">www.tvrepairworld.com</A> the kit contains the ICs , Resistoirs and the cd with repair instructions.
Projecting double images
When convergence output ICs got failed, tv shows double image or 3D like picture. Replace convergence output ICs in tv to fix the issue. Local tv repair shop will replace it for you.
When i turn my tv on i have no picture and i hear a beeping noise
Hi
Thanks for using FixYa. From what you have described it seems that you
have to replace the convergence IC and also check the power resistor, if values
are not exact you have to replace them. These ICs are located behind the black
heat sink; you can see once you open the back off the TV. The convergence board
should be checked for cracked solder joints and please make sure to check the
resistors as if they are shot the ICs might blow again. All this is only
recommended if you have electrical expertise and know how to solder/re-solder
components. Please also make sure to turn off and unplug the TV for at least 1
hour to drain off the current from all the components especially capacitors
before you perform any repairs. Also note that the TV consists of very high
voltages even when it is in off condition. Please do rate the solution if the
issue is resolved or post a comment for further assistance.
Thanks
Rylee
Does it have a built in tunner?
It has an NTSC (analog) tuner. You'll need a digital to analog converter to watch most stations. Low power stations are still available in analog in some areas.
I hope this helps.
Cindy Wells
Not finding what you are looking for?