20 Most Recent Konica Minolta magicolor 2400 Laser Printer - Page 7 Questions & Answers

Hey Mike,

It is normal for these rollers to become dirty. Be very careful not to scratch it, you will have to replace the whole fusing unit and not only the roller and the whole unit it's not cheap at all.

Reset your Toners and Imaging units for Bizhub and CF series.
http://www.chipreset.eu

Remove each toner and shake it well for a few times. After this, put it back.

Start the Konica Minolta Status application and check the error, you should get more info there.

Reset your Toners and Imaging units for Bizhub and CF series.
http://www.chipreset.eu

Start the Konica Minolta Status application and check the error, you should get more info there.

Reset your Toners and Imaging units for Bizhub and CF series.
http://www.chipreset.eu

It is called transfer belt or transfer kit, you can find it on any KM dealee but I have to warn you it's not cheap.

Start the Konica Minolta Status application and check the error, you should get more info there.

Reset your Toners and Imaging units for Bizhub and CF series.
http://www.chipreset.eu

You didn't setup the paper size correct, check again in the driver and application to have the same dimension with the actual paper in printer.

Reset your Toners and Imaging units for Bizhub and CF series.
http://www.chipreset.eu

Start the Konica Minolta Status application and check the error, you should get more info there.

You didn't setup the paper size correct, check again in the driver and application to have the same dimension with the actual paper in printer.

Try to pull it down, from the inside of the machine. If it is not taken out in one piece, you need to call a tech.

check the two levers with an envelope on each, to the left and right of the fusing unit, should be pressed down and not rise up.

Start the Konica Minolta Status application from your PC, it will give you more details about the error.

Start the Konica Minolta Status application from your computer, it will give you more info.

have you read if you need your windows up to date? like windows xp/vista sp2?? or maybe your windows need an extra component.try this update your windows google this window update then follow the microsoft links and this will fix your problem for ya'

Download them from Konica Minolta:
http://onyxftp.mykonicaminolta.com/download/SearchResults.aspx?productname=magicolor%202400

Select the appropriate driver for your systenm OS and language.

This is a common fault on all Magicolor 2400, 2500 series printer. the cause is the 3 pin contact on the bottom RHS of the machine which touches each cartridge chip as they rotating across so that the machine can find out how much pages each individual cartridge has done or how much percent has got left.
This 3 pin contact tends to lose the tension
as the machine done about 7-8k pages so it does not contact with the chip firmly. the complete solution is to replace a new 3 pin contact but I don't know if konica stocks this item. Temp. fix can be done by bending each pin a little bit outward, but you have to remove this assy outside from the machine first.

I had the same problem and this worked, although it is not the answer to your question:

Take a standard manila file folder and cut it to the basic shape of a standard piece of paper. When you lift the top cover on the under side you will see a diagram on how to pull the paper out in the case of a paper jam. Feed you file folder up from the bottom and you will ~ with a little work, more than likely be able to clear the jam.

I would suggest cleaning the printer first to see if any ink or small debris was left.

But, since the problem occurred after you replaced the cartridge, I suspect that your new cartridge is faulty and needs to be replaced and returned.

Hope this helps.

reinstall the printer driver, if the problem were still there change the usb cable, if doesn't work before you send the printer to repair just try chaging the computer, try install it in another one.

this link must help you

thank you