20 Most Recent Konica Minolta magicolor 2400 Laser Printer - Page 3 Questions & Answers

either you will have to download it directly from internet into that system or copy it into a pen drive through some other system and then instal in your system. thanks.

First of all, here is the main ONLINE SUPPORT page for your model:

http://printer.konicaminolta.com/support/current_printers/mc2400w_sup.htm


And here is a direct link to the ONLINE USER'S MANUAL for that model:

http://ec1.images-amazon.com/media/i3d/01/A/man-migrate/MANUAL000066617.pdf


To view the Support Page or the Owner's Manual with Operating Instructions just use your mouse to click on the link, which is the underlined and highlighted text just above. This will open a new web browser page automatically for you and allow you to view the information at the website indicated and the contents of the Owner's Manual.

You may need ADOBE READER installed on your computer to read PDF documents.
You can download this free at WWW.ADOBE.COM if necessary.
Click on the DOWNLOAD ADOBE READER button on right side of the ADOBE home page when you get there, the follow the onscreen instructions to install the software on your computer.

Ensure you have the correct paper size selected in the PAPER TAB of your printer driver preferences options. See page 12 of the manual for details.

If you are not using the supplied driver for the printer, you can always download it at the main support page above.

Please comment back here to this page if you have any details to add, have any questions, have difficulty accessing the links, or just require further general assistance and I will respond as soon as I see it.

Thank you very much and good luck.

Joe.

The possible reason for error is the printer does notread chip on the cartridges.
The reader for chips locate inside the printer bottom ofcartridges.
Take out all cartridges and you see reader it is a small blackplastic which come three contact plates.
Just clean it with compressed air and take out if some contactplate is sedentary.

Hi. The only way to reset the toner error is to replace the counter chip on the toner cartridge since this is a re-manufactured toner. These should go for about $10 a piece. Otherwise, you can set the engine to continue on error.

clean the feeding roller

If the feed rollers are turning when you try to print, then clean them off with a soft cloth dampened with alcohol. You probably have paper dust on them and they're slipping.

Please get the correct driver here : www.printcountry.com/drivers.asp
www.opendrivers.com/.../printers-free-driver-download.html
www.driversdown.com/driverslist/r_4_1.shtml
Regards, Jay__6yhdfr4

this is a setting that makes in the printer driver, just fixed

Hi there,
For starting print spooler service, Go to start menu>control panel>administrative tools>Services
Search for Print spooler, (simply type pr) and it will show you print spooler service, right click on the service and click start,
if the start is disabled, Click on properties In the general Tab you will will see "Startup Type" change the settings to "Automatic" Click apply and save Then right click the service and select start, you will now be able to print
If you require more assistance feel free to reply to this post
Regards-BA

see more paper inside, caused jam

dont understand your problem quite well, but, for a connection problem, update driver, change usb cable and last if nothing helps, update firmware.
for a paper take up problem,:
turn off printer,
remove cover,
remove drum cartridge,
under that there is take up roller, pull the knob and move the roller to right, then you can pull the take up roller out.
first try to clean it and also clean plate under the take up roller. if thats not helping, then you have to cut the biger (larger) plastic sides of the take up roller a little smaller..
should help.
good luck

Error 17H is a rack rotation failure:
The toner cartridge(s) may not be sitting correctly, which would be the easiest fix - otherwise you have to carefully examine the inner workings of the printer itself, to see what is causing the rack to get jammed or slowed down at some point along the way.

1. Check the control panel to see which color of toner is empty. As an example, the procedure for replacing the cyan toner cartridge is described below. I f the Auto Toner Replace check box of Mode Setting in the Status Display was selected, printing stops when the toner is empty, and the empty toner cartridge moves so that it can be replaced. .

2. Press the Rotate Toner key. The lit indicator for the cyan toner goes off, and then the toner cartridge carousel rotates. When the cyan toner cartridge is positioned so that it can be replaced, the indicator for the cyan toner lights up again. Press the Rotate Toner key once to move the cyan toner cartridge so that it can be replaced. With each additional press of the Rotate Toner key, the black, yellow, then magenta toner cartridge moves so that they can be replaced. The indicator for the toner cartridge that was moved so that it can be replaced lights up.

Installation:

Pull the lever, and then open the top cover. If there is paper in the output tray, remove it, and then fold up the output tray before opening the top cover. Do not touch the transfer belt.

2. Carefully pull out the drum cartridge.

Dispose of the used drum cartridge according to your local regulations. Do not burn the drum cartridge.

3. Prepare the new drum cartridge. Do not touch the PC drum on the drum cartridge.

4. Install the new drum cartridge.

5. Carefully close the top cover.

The printer must complete a calibration cycle (less than 2 minutes) after the drum cartridge has been replaced. If you open a cover before the printer is reset, the calibration stops, then starts over again after the cover is closed.

Also try:

1. Double-click the magicolor 2400W Status Display icon in the System tray, ORgo to Start/Programs/KONICA MINOLTA magicolor 2400W Utilities and select KONICA MINOLTA magicolor 2400W Status.
2. In the resulting dialog box, select Printer from the menu bar, then select Mode Setting from the drop-down.
3. You will then be allowed to change the state of the Toner Empty Mode.
magicolor



1. Panel should say READY.
2. Press MENU/SELECT button.
3. Press Right arrow button until you see ENGINE.
4. Press MENU/SELECT button.
5. Press Right arrow button until you see TONER EMPTY.
6. Press MENU/SELECT button.
7. Press Right arrow button until you see the desired state for the action when toner is empty.
8. Press MENU/SELECT button.
9. Press Up arrow until you see READY.

Go to the Control Panel and click on Add/Remove and find the item and then click remove, this will take it off the system. PLEASE let me know if you still have problems, I would be glad to assist you further..... Take care, Guy S. :)

Hi,

This is because the margins are defined on the printing settings.

You may go to Printing preferences and change the same, if you prefer.

If this doesn't work for you, please comment and let me know, and I will be more than happy to assist you to further resolve your issue.

I will appreciate your feedback and positive rating for this solution.
Thank you.

did you try to check the sensors and actuators? maybe the actuator sensor didn't return

Hi,
Click on the link below to setup the page.
http://ulearnoffice.com/word/printing.htm
Good Luck!

Hello there,

I would suggest you try plugging it into another USB port. Also, this problem could manifest an issue with the USB cable you are using. To troubleshoot, try to replace it with a new one.

Looking forward to your response.