Timex 1440 Nylon watch - Answered Questions & Fixed issues

Hold down the adjust button bottom right then press the mode button top left you will notice the a or p that stands for am/pm will disappear & reappear. If you have an a or p on your display then you are out of military time.

Try this: To set time and date: 1) With time and date showing, press SET. 2) Seconds ?ash. Press START/STOP to round time to nearest minute, setting seconds to zero. 3) Press MODE. Hour ?ashes. Press START/STOP to change hour, including AM (no symbol) and PM. 4) Press MODE. Minutes ?ash. Press START/STOP to change minutes; hold button to scan values. 5) Press MODE. Month ?ashes. Press START/STOP to change month. 6) Press MODE. Date ?ashes. Press START/STOP to change date. 7) Press MODE. Day ?ashes. Press START/STOP to change day. 8) Press MODE. Time format ?ashes. Press START/STOP to select 12- or 24-hour time format. 12-hour format has AM/PM. 9) Press SET, at any step, to exit and save settings. Date (day of month) appears in upper part of display in Time mode. Press and hold START/STOP to see month and date in large digits.

My watch has model number 504-tsk085, labeled Timex 1440 Sports, and Timex provides the incorrect manual for it online. I wrote these instructions after careful experiment: Upper left button: press to switch to a stopwatch, or... Press and hold to enter alarm setting mode. Once flashing press again to enter time/date setting mode. -- you can only do one or the other without exiting the setting mode (time or alarm set). - within the setting mode you use the two right side buttons in obvious ways to set times/dates Exit setting mode by pressing upper left again Lower left button: light Upper right button (when not setting time): reveal date while pressed Lower right button (when not setting time): reveal alarm time while pressed. ALSO: WHILE lower right button is pressed you can change alarm on/off and chime on/off through the four possible settings by secondarily pressing the upper right button repeatedly.

Hot to set alarm on my AW91-729

You probably need to go to a watch repair professional. Any business that replaces watch batteries should be able to help you. They have a special press designed to support the watch safely while they snap the back onto the case. This sometimes takes quie a bit of force and rqeuires that the watch case and back plate be perfectly aligned.

Hi markie_d,

To set the digital time and date on your Timex, please follow the steps below.

Timex Digital Watch

1. Press and hold the "Set" button for 2 seconds. The "Set" button is on the lower right side.

2. Press the "Date Advance" button on the upper right side. This will reset the seconds.

3. Press the "Change Mode" button on the lower left to set the hour. The hour will flash. Press the "Date Advance" button until the correct hour is displayed.

4. Press the "Change Mode" button again to set the correct 10s unit (first digit 1 or 0) for the minutes. Press the "Date Advance" button until the correct first digit of the minutes is displayed. Repeat this step to set the second digit of the minutes.

5. Repeat Steps 1 through 4 of this section to set the year, month, date and day and whether to use 12- or 24-hour time for your watch.

6. When finished, press the "Set" button (on the lower right) to return to the current time view and lock in your settings.

Hope it helps.

Thank you for using FixYa.

Change the Time Zone ( to Pacific Time) or subtract 3 hours from your NYC time. Don't bother about the minutes.

go here > http://assets.timex.com/manuals/?timexBrand=core

this link is the manualhttp://assets.timex.com/user_guides/W207_M115/W207_M115_NA_EN.pdf

How to set the date

open it carefully or visit store

Press and hold SET, then press START/STOP. This should turn the chime on. Press it again to turn on the alarm.

Press the MODE button. Then hold and press reset/lap button for 2 seconds. Press mode button again.Press Start/Stop to set the Hour.Press mode button again. Press Start/Stop to set the Minute.

The manual is right here...http://www.timex.com/info/Product_Instruction_Guides_Downloads

If its a good watch, take it to a watchmaker. Dont know to find one 30 yrs ago they were inevery city

press and hold mode button until the digits flash (it is to set the alarm) then press again once the mode button, this time the time flash to be set, the digit that flash is changeable, the lower right button is for adjusting, the upper right button is to choose what you are going to change, while pressing the upper right button you will see all you have to change the time , the date, the day of the week. if your done with all of this. press mode button once, i hope i had been helped you.

Hi 1234910,

To set the digital time and date on your Timex, please follow the steps below.

1. Press and hold the "Set" button for 2 seconds. The "Set" button is on the lower right side.

2. Press the "Date Advance" button on the upper right side. This will reset the seconds.

3. Press the "Change Mode" button on the lower left to set the hour. The hour will flash. Press the "Date Advance" button until the correct hour is displayed.

4. Press the "Change Mode" button again to set the correct 10s unit (first digit 1 or 0) for the minutes. Press the "Date Advance" button until the correct first digit of the minutes is displayed. Repeat this step to set the second digit of the minutes.

5. Repeat Steps 1 through 4 of this section to set the year, month, date and day and whether to use 12- or 24-hour time for your watch.

6. When finished, press the "Set" button (on the lower right) to return to the current time view and lock in your settings.

Hope it helps.

Thank you for using FixYa.

Hi r3girls1,

To set the digital time and date on your Timex, please follow the steps below.

Timex Digital Watch

1. Press and hold the "Set" button for 2 seconds. The "Set" button is on the lower right side.

2. Press the "Date Advance" button on the upper right side. This will reset the seconds.

3. Press the "Change Mode" button on the lower left to set the hour. The hour will flash. Press the "Date Advance" button until the correct hour is displayed.

4. Press the "Change Mode" button again to set the correct 10s unit (first digit 1 or 0) for the minutes. Press the "Date Advance" button until the correct first digit of the minutes is displayed. Repeat this step to set the second digit of the minutes.

5. Repeat Steps 1 through 4 of this section to set the year, month, date and day and whether to use 12- or 24-hour time for your watch.

6. When finished, press the "Set" button (on the lower right) to return to the current time view and lock in your settings.

Hope it helps.

Thank you for using FixYa.

Hi,

Please follow the procedure below.

1. Press and hold the "Set" button for 2 seconds. The "Set" button is on the lower right side.

2. Press the "Date Advance" button on the upper right side. This will reset the seconds.

3. Press the "Change Mode" button on the lower left to set the hour. The hour will flash. Press the "Date Advance" button until the correct hour is displayed.

4. Press the "Change Mode" button again to set the correct 10s unit (first digit 1 or 0) for the minutes. Press the "Date Advance" button until the correct first digit of the minutes is displayed. Repeat this step to set the second digit of the minutes.

5. Repeat Steps 1 through 4 of this section to set the year, month, date and day and whether to use 12- or 24-hour time for your watch.

6. When finished, press the "Set" button (on the lower right) to return to the current time view and lock in your settings.

Hope it helps.

Thank you for using FixYa.

Hi bud76502,

To use 12- or 24-hour time for your watch, please follow the instructions below.

1. Press and hold the "Set" button for 2 seconds. The "Set" button is on the lower right side.

2. Press the "Date Advance" button on the upper right side. This will reset the seconds.

3. Press the "Change Mode" button on the lower left to set the hour. The hour will flash. Press the "Date Advance" button until the correct hour is displayed.

4. Press the "Change Mode" button again to set the correct 10s unit (first digit 1 or 0) for the minutes. Press the "Date Advance" button until the correct first digit of the minutes is displayed. Repeat this step to set the second digit of the minutes.

5. Repeat Steps 1 through 4 of this section to set the year, month, date and day and whether to use 12- or 24-hour time for your watch.

6. When finished, press the "Set" button (on the lower right) to return to the current time view and lock in your settings.

Hope it helps.

Thank you for using FixYa.