Kenmore 44921 Front Load Washer - Answered Questions & Fixed issues

you can run a regular cycle with bleach as instructed in the manual. there may be mold on the rubber where the door closes. wash this with water and bleach. to avoid this problem in the future you can loosen the light bulb then you can leave the door open a little all the time with no light. press the off button when not in use.

Hi, it sounds like you have a major problem with your washer. The inner steel basket has a shaft attached to the back of it that goes through the rear of the outer plastic tub and attaches to the drive pulley. More than likely the shaft has broken off, the basket alone is over $500.00. It will more than likely need the rear of the tub as well for the seal and bearing. I have seen this many times. I would recommend buying a new washer unless you have some sort of extended warranty.

Assuming you mean the hose which goes into the pump, it would be part number 8181732,

Available from Sears http://www.searspartsdirect.com/partsdirect/part-number/Kenmore-Parts/Washer-Parts/8181732/0026/110/Model-11044921302/0582/0153200?keySuffixId=NA&productTypeId=x&searchModelNumber=11044921302&subCompDesc=Pump%20and%20motor&brandDesc=KENMORE&modelDesc=RESIDENTIAL-WASHER&blt=11


or RepairClinic http://www.repairclinic.com/PartDetail/Pump-Hose/906517?modelNumber=110.44921302

Hi
To unlock them press and hold the DRAIN/SPIN button for 10 seconds. Hope this helps....
Daniel

Check on the drain valve /drain pump and test if the voltage comes to the component. If so the drain pump is not working well. You can remove and test on bench, clean and back flush to remove dirt and see for a good flow. Once confirmed refit or else the pump must be replaced if the pump is not performing as required , the coil can be faulty.
However if voltage is not present on the pump after the wash cycle and during the rinse cycle, the controller can be defective.

Hi,

"FH" is a No Water Detect error.It is an indication that you either have no water coming into the washer, or very little water at all. Check whether the water taps are turned on sufficiently, the inlet hoses are not kinked, the water inlet valve is not clogged, you don't have a siphoning issue, and/or the drain pump is working.


Thank you !!

Hi


Thanks for using FixYa. Error code F/H means no water was detected entering machine or Pressure switch trip not detected. If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed. It can also happen if the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash. You’ll need to Press PAUSE/CANCEL twice to clear the display and then check:

• If there is no water in the unit:
• Make sure that both valves at the water source(s) are turned on all the way.
• Check for plugged or kinked inlet hoses or plugged screens in the inlet valves
• Verify inlet valve operation
• If there is water in the unit:
• Verify Drain pump operation
• Pressure Switch Hose is in good condition and properly connected to Tub and
Pressure switch
• Verify there is not a siphon problem
• Verify wire harness connections to; Inlet Valves, Pressure Switch, Drain Pump,
Flow Meter and Central Control Unit (CCU)
• Check all hoses for possible leaks
• Verify pressure switch operation
• Verify flow meter operation
• Verify CCU operation


Please do rate the solution if the issue is resolved or else revert for further assistance.


Thanks
Rylee

"F02" is a Long Drain error code. This is an indication of an obstruction somewhere in the drainage system. In most cases, the drain pump reservoir needs to be cleaned out. The following link explains how:

http://www.fixya.com/support/r3574284-checking_the_drain_pump_on_a_front_loade

If you check the drain pump reservoir and the problem still persists, you may have a pump with a damaged motor/impeller, or something lodged in one of the drain lines. In particular, the drain line that runs from the bottom of the wash tub to the inlet side of the pump.

I recommend you remove the inlet hose, as well, and inspect for clogs. In is common for small garments to become lodged in this area and restrict water flow to the drain pump. Check the output drain line for obstructions as well.

It does not take much to damage this small drain pumps. The error code is generated if the drain cycle exceeds 8 minutes. So...if the impeller or motor become damaged, and the pump does not pull water at the correct volume, you may still experience the drain error. In this case, you will have to replace the pump in order to get the error to clear. The following link explains how:

http://www.fixya.com/support/r3574350-replacing_the_drain_pump_in_a_front_load

Replacements can be purchased at any of the following websites:

searspartrsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com

Prices vary between sites, so shop and compare. the first three sites listed also have helpful exploded view parts illustrations to assist you with locating and properly identifying the parts you may need.

If you have any questions, please post back and let me know. I hope this helps you.

All front loader have this problem. Use concentrated lemon juice to clean the boot and then you will have to leave the door ajar just a bit every time you finish washing. Sorry but this the nature of having a front loader. Also using powdered soap products will also almost completly do away with this problem.

this is a drain problem.inspect the water pump, motor coupler and the drain hose for kinks.

if softner has discharged it's probably working ok some water left behind is normal

If this is a 417 model your problem might be the pump itself. There is a pressure switch that detects whether or not there is any water left in the tub. If so, it will not go into high spin. Remove the lower panel and check the pump on the lower right side. See if there is any gunk or coins in there by removing the hoses attached to it. Have a flat pan or a bunch of towells ready to catch the remaining water from the tub. If the pump checks ok, the next move would be to check the motor controller itself.

Check out the link for Kenmore Parts suppliers. https://www.google.com/search?q=Kenmore+series+200+triple+action+agitator+parts ..

If it is only leaking when you use warm water it is likely a leak from the delivery side of the hot water inlet solenoid. The only way to check is to remove the top and look. https://www.google.com/search?q=Kenmore+80+series+washer+92281100+leaks ..

Question edited for clarity. 'then', a moment in time. 'than', a comparison between one thing and another. It depends on the model, but usually related to the lid lock. Also check the breaker. Why does my washer stop working after filling with water? If the Top Load Washer stops after filling with water, be sure to check the house circuit breaker/fuse as well as the outlet and plug. Washers should be plugged into their own separate, dedicated outlet. ..

Usually it's the lid switch..When you open the lip look straight down usually..When you close the lid it inserts a small plastic piece that goes into the hole telling the washer the lids down..If it broke it will make the washer stop mid cycle..You can stick a wooden (only made of wood) into the hole and sometimes it will start to work..Then you know that's the problem and just get your model number of the washer and replace it..Hope this helps

You start with under the agitator, then the filter, then the pump, then the hoses at the base of the drum and then everything else. Then you find nothing and remember you took it out of your pocket and put it in........ ..

You normally start from the back. It will be the opposite or the videos.

HOw to remove back from kenmore series 70 washing ...

JustAnswer https://www.justanswer.com > Appliance Repair Mar 6, 2012 - Below is a link to a video that shows you how to take the cabinet off the washer. CLICK HERE. 1 answer · Top answer: no problem and I wish you only the best of luck. If you're handy this should re ..

Troubleshooting: Check the drain hose: Ensure that the drain hose is not clogged or kinked. If it is, straighten it out and remove any blockages. Inspect the drain pump: Check the drain pump for any debris or foreign objects that may be blocking it. Clean it out if necessary. Check the lid switch: Ensure that the lid switch is functioning properly. If it is faulty, it may prevent the machine from starting the drain cycle. Check the waste hose: Ensure that the waste hose is not clogged. A clogged waste hose can prevent water from flowing out of the machine. If this troubleshooting does not work, you may have to turn to professional assistance from a repairman.

For some reason, it is failing the self diagnostic tests. You need a service engineer, because the reason is likely the main control board. For that reason you need the correct diagnosis and warranty on the part and the work performed. This is not a simple fix. If the machine is old it may be prudent to just replace it.