Top 20 Bosch WET 2820 Front Load Washer / Dryer Questions & Answers

No its the water censor located inside the machine is blocked,remove back cover you will find a small plastic pipe leading upwards,remove it and clean out the lug it came from with a ear bud or other un sharp device the pipe as well,gently blow into the pipe you should hear a clicking sound this is the water level indicator to the programmer to stop filling, replace it carry on washing eric992

press the helpful button ,links below for your Bosch WET 2820 Download instruction manuals http://laundry.manualsonline.com/support/other/washerdryer/wet-2820-washerdryer-manual-5233637 User manuals Service Bosch Professional http://www.scribd.com/doc/286185567/bosch-wet-2820-manual-download-fast#scribd

Buy new belt for washer, pop off back plate, put new belt on. If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a

BOSCH washing machine WET 2820 This video will show you how to change the door eal washing machine Please remember to subscribe to our YouTube channel for all appliance tutorials a 4 THUMBS rating is appreciated for answering your FREE question. And don't forget to like us on facebook

Hi from retired Englishman in SW France,

I'm so sorry but this forum is not able, nor in a position, to supply any type of manual, parts list, installation instructions, electrical or schematic diagrams direct; it's just made up of ordinary guys and gals, probably at home and from all over the world, with experience of addressing problems and giving guidance for free on the web ;-0)
Also members on Fixya are not 'affiliated' to, or representative of, any manufacturer at all, just using their experience gained probably over many years.

Manual
You will need to type into your search engine/web browser '(make model number) washer manual' and you should be presented with a number of sources from which you can either download for free or have to pay a nominal amount.
You could also try the manufacturer's web site direct ;-0)

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C.

Hi from retired Englishman in SW France,

If these are the same symptoms as previous get the service person back in- I would expect there to be some sort of warantee/guarantee?

Otherwise (sorry, no promises)- I would gently suggest as a first step that you clean the drain motor/pump lint tray/filter. So many 'faults' are caused by blocked filters and many machines will not even go to rinse or spin or release the door lock if there is any water still left inside.
Following are my complete and generic guidance notes for checking both the drain motor filter and the drain motor ;-0)
REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT (alternatively use a wet vac as sensibly suggested by VinnyB1234!)If you are unsure where the filter is, it is often behind the front lower (kick) panel (or in some machines at the rear in an awkward position!). These panels are either held on by (plasic) screws or will just pull off. Most filters are held in by a round cover/knob. Sometimes the filter will not come out with the cover and you will have to persuade it to come out to play.
It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. Using something suitable like a glove see if it is easy to briefly slow the motor down. If it is easy then the motor is malfunctioning.

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

Hi from retired Englishman in SW France,

I would gently suggest as a first step that you clean the drain motor lint tray/filter. So many 'faults' are caused by blocked filters and many machines will not even go to spin or release the door lock if there is any water still left inside.
Here are my complete guidance notes for checking both the drain motor filter and the drain motor ;-0)

If you are unsure where the filter is, it is often behind the front lower (kick) panel (or in some machines at the rear in an awkward position!) and most are held in by a round cover/knob. Sometimes the filter will not come out with the cover and you will have to persuade it to come out to play!

REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT!
It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. Using something suitable like a glove see if it is easy to briefly slow the motor down. If it is easy then the motor is malfunctioning!

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

Bosch WET 2820 Front Load Washer / Dryer waterLeaking.This video will show you how to change a door seal on this Bosch front loader washing machine .we have all bosch repairs in our channelPlease remember to subscribe to our YouTube channel for all appliance tutorialsa 4 THUMBS rating is appreciated for answering your FREE question.

the water inlet valve is letting the water by, you will need to fit a new one. to get the correct part number you will need the model number which u already have and the "FD" number to get the specific model as there are a couple of varients. you should find the fd number on the silver rating plate inside the door

Hi,

If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.

if you dryer is gas check out this gas no heat tip....

If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.

check out this electric no heat tip...

heatman101








//////////

I am not a repair professional. I am just a 78 year old
man who has been making his own repairs for about
50 years. Therefore the washer or dryer ID doesn't
mean much to me. I came to fixya looking for a
schematic for an really old AM/FM radio and
discovered that more than 4,700 people were asking
for help with a washer repair. I recently had a washer
repair of my own and found an excellent video which
showed me how to take my machine apart. This
video made it possible for me to do my own repair. I
was so impressed with the video that when I saw all
these people needing help, I wanted to tell them
about it. If you have a top loader (washer) of the
direct drive type, this video might be a Godsend for
you. If you look at the back of your washer and the
panel is solid (no small inspection plate to remove)
chances are you have a direct drive and this video
is just what you need. You can see this video at
www.acmehowto.com You will probably need
more help in determining what the problem is and
how to fix it. If your repair problem is a washer or
dryer I suggest you go to www.applianceaid.com
where they have very good trouble shooting and
repair information on most washers and dryers.
I think you'll find what you need there. Don't worry
about the timer, they hardly ever go bad. Good
luck with it. If I have helped you, please rate my
advice on fixya.

I have noticed on bosch website that WFT2806 is exactly the same model and there is a manual to download.

go to http://www.bshappliancecare.com/Bosch/ and select instruction manuals then search for WFT and wait, the page will authomatically redirect you to the manuals for WFT2806GB which I think is the free standing version of the washer.

enjoy.

I managed to solve the problem the following way: I noticed that if you unplug the Sensor-NTC(part nimber 154431 https://www.bosch-eshop.com/eshop(bD1lbiZjPTAwOQ==)/bosch/gb/prodp.htm?prod=WET2820GB%2f13 ) that controls temperature of air in the air channel, the drying cycle runs as you describe above. So this circute was checked up to the power module. Contacts of the Sensors plug were tightened; I think this solved the problem; resistance of the sensor checked. It must be 4.8K at 25 degree C. and decrease when temperature increases. I dipped the sensor in a glass with hot water. 

Have you tried simply unplugging the machine - that is if you can get to the plug. Or, you could always flip the circuit breaker off. Either way, leave it off for a minute or two, and that should give it time to forget what it was doing. Once you start it back up, it should unlock, unless it has some kind of static memory that survives power outages.

That sounds like the bearings have collapsed. Time to call a domestic appliance engineer or look for a new machine.

Potential causes and fixes: Battery Terminal Corrosion: Cause: If your Bosch laser receiver has been submerged in water, the battery contacts and sometimes the circuit board may have corroded. Fix: Remove the batteries and clean the battery terminal contacts. Pry open the bottom cover and clean any corrosion on the circuit board. Calibration Issues (for Bosch GLL 2-20): Cause: Dropping the Bosch GLL 2-20 can lead to misalignment and errors. Fix: The best way to address this problem is to calibrate the laser level. You can either contact the Bosch service center or follow the calibration instructions in the manual. General steps for calibrating a laser level with a misaligned pendulum: Remove the screws and outer cover. Locate the pendulum hanging in its stationary position. Remove the glass window of the laser level. Adjust the stationary position of the hanging pendulum using the main adjustment screw. Fine-tune right-left adjustments using other smaller adjustment screws. Reassemble the laser level. Cracked Glass Lens (for Bosch GLL 2-50): Cause: If the horizontal glass lens is cracked, it affects accuracy and safety. Fix: Unfortunately, this problem is often unrepairable. It's advisable to replace the laser level to ensure safe operation1. Remember to lock your laser level when not in use or during transportation to prevent pendulum movement1. If these steps don't resolve the issue, consider reaching out to Bosch for professional assistance or repair

You will need the numerical model number.

Bosch - Door Boot Seal 00701333 - Appliance Parts

PartSelect.ca https://www.partselect.ca > PS8735900-Bosch-0070133... Nov 10, 2021 - Door Boot Seal ; This part fixes the following symptoms: Leaking ; This part works with the following products: Washer. ; This part works with the ... Rating: 5 · ‎ 1 review

00667487 Bosch Washer Door Boot Gasket

Reliable Parts https://www.reliableparts.ca > ... > Bosch Dishwasher Parts Door boot gasket works with some Bosch, Thermador, and Gaggenau models of washing machines. This is a genuine OEM part that works for some models of Bosch, ... $101.27 · ‎ In stock

Shop Bosch Washing Machine Gasket & Seal Parts

Repair Clinic https://www.repairclinic.com > Shop-For-Parts > Bosch-... Find Bosch Washing Machine Gasket & Seal Replacement Parts at RepairClinic.com. Repair for less! Fast, same day shipping. 365 day right part ..

The switch needs testing or replacing. https://www.google.com/search?q=Bosch+Classixx7+door+switch ..

Question edited for clarity. Question moved to maker category. See the link. It may be 'child locked'. https://www.google.com/search?q=bosch+washing+machine+will+not+unlock ..

That will usually happen when the bearing is worn or the shaft has moved on the seal.