Motorcycles - Page 5 - Popular Questions, Answers, Tips & Manuals
How to remove filter and clean it?
Year Make Model of the motorcycle please?
Please always include that information as first three words. Then they are thousands of motorcycle categories listed by;
make year model = Suzuki 2003 GSXR1100
If it is the foam type filter, put Dawn Dish Detergent on it, wash out the dirt, dust and oil. Keep squeezing under running water until the water runs clean. Leave to dry. Then spray it with Oil Filter Oil and replace the filter. For paper filters, just replace them if they look dirty.
99-0516 K&N Air Filter Oil - 12.25oz - Aerosol
K&N
https://www.knfilters.ca > 99-0516-air-filter-oil-12-25...
K&N 99-0516 is a 12.25 ounce aerosol can of air filter oil. K&N Air Filter Oil is the only oil specially formulated to work in combination with the cotton ...
US$15.99 · In stock
..
12/12/2023 10:57:17 PM •
Motorcycles
•
34 views • 0 helpful votes
Where is air/fuel screw on a suzuki vs 800 intruder
The air/fuel mixture screw on a Suzuki VS800 Intruder is typically located on the carburetor. To adjust the air/fuel mixture, you'll need to locate the carburetor and look for a small screw that can be turned.
Keep in mind that the exact location of the screw may vary slightly depending on the model year and specific carburetor version on your VS800 Intruder. Generally, it is located on the bottom or side of the carburetor.
Here are the general steps to locate and adjust the air/fuel mixture screw:
1. Locate the Carburetor: The carburetor is usually positioned on the side or underside of the engine. Follow the intake manifold or air filter housing to find the carburetor.
2. Identify the Air/Fuel Screw: Look for a small screw on the carburetor. This screw is typically flat-headed and may be recessed. It is often located near the bottom of the carburetor.
3.Adjustment: With the engine running at idle, use a screwdriver to turn the air/fuel mixture screw. Turning it clockwise (in) usually leans out the mixture, while turning it counterclockwise (out) enriches the mixture.
4. Listen to the Engine: As you make adjustments, listen to the engine's sound. The goal is to find the point where the engine runs smoothly and the idle is stable.
5. Fine-Tune: Make small adjustments and give the engine a moment to respond before making further changes. It's a process of trial and error to find the optimal setting.
6. Check the Owner's Manual: Refer to your motorcycle's owner's manual for specific guidance on the location and adjustment of the air/fuel mixture screw. The manual will provide information tailored to your bike's make and model.
If you're uncomfortable making these adjustments yourself or if you're unsure about the location of the screw, it's advisable to consult a professional mechanic or refer to the specific service manual for your Suzuki VS800 Intruder.
11/13/2023 4:25:10 PM •
Suzuki...
•
63 views • 0 helpful votes
What to torque the head on my 99 CBR 929 Honda in
For a 1999 Honda CBR929RR, the cylinder head bolt torque specifications are essential to ensure proper engine assembly and function. When tightening the cylinder head bolts, it's crucial to follow the manufacturer's recommended torque settings to prevent damage to the engine components.
For the CBR929RR, the cylinder head bolt torque specifications are typically as follows:
1. **Initial Torque:** 29 Nm (2.9 kgf-m, 22 ft-lbs)
2. **Final Torque:** 64 Nm (6.4 kgf-m, 47 ft-lbs)
It's essential to tighten the cylinder head bolts in the specified sequence and in multiple stages, gradually increasing the torque until reaching the final specified torque. The exact tightening sequence can usually be found in the service manual specific to your motorcycle model.
When torquing the head bolts, ensure you're using a reliable torque wrench calibrated in the appropriate units (Nm or ft-lbs). Always follow the tightening sequence precisely to ensure even pressure distribution across the cylinder head gasket.
Additionally, it's advisable to use new cylinder head bolts if the old ones have been previously tightened or stretched beyond their yield point. This helps maintain proper clamping force and ensures the integrity of the engine assembly.
As always, referring to the service manual or consulting a professional mechanic experienced with motorcycle engine assembly can provide additional guidance and ensure the correct torque settings are applied during the cylinder head installation process.
11/23/2023 4:53:22 PM •
Honda...
•
48 views • 0 helpful votes
Not finding what you are looking for?
