I have gas dripping from the outside of my carb . It is forming on the bottom next to the jugs and drippind down my idle adjustment. it is a 1998 suzuki vl 1500 lc intruder

Excess air or not enough air. Replace air filter. Spray outside of carb to clean & ensure choke movement is smooth. Water in gas may cause this also. Flush out tank, refill with fresh gas, always use Stabile.

you have a vacum leak at at the boot from the jug to the carb check for cracks i the boot

Sometimes Honda ATC's wont idle if the exhaust valve is too tight. Check and clean the slow circuit of the carburetor this should fix the other part of the idling problem. A carb gasket set from Honda should have all the components you need to properly seal the carb. Lastly, buy a new carb float needle this should stop the dripping unless you have damaged the drain screw on the bottom of the bowl. This can only be purchased as part of the complete bowl assembly.If you still are having problems after this, try adding an additional fuel filter between the tank and fuel petcock, just in case tank rust is the cause of the needle sticking open and dripping.

Has the bike been sitting??? If the carbs are gummed up from sitting and the float and or float needle get stuck in the "add fuel" position it could cause this

ALWAYS have a fire extinguisher on hand when working on carburetors.
Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

Drain the carburetor. There should be a screw on the lower side or a plug on the bottom of the carb float bowl. Remove the screw/plug then replace it after the fuel drains. Remove the carburetor from the engine.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the carb and spray into the screw holes as well. The diagram below depicts the problem area. The bike will idle properly once the pilot jet and related passageways are cleared.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Put the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine.



Please rate this solution. Thanks!

The idle circuit is plugged up. ALWAYS have a fire extinguisher on hand when working on carburetors.
Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

Drain the carburetor and remove the carburetor from the engine. Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the carb and spray into the screw holes as well. Pay special attention to the pilot jet area.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. This process should get you back on the road. A “very helpful” rating for this answer? Thanks!

ALWAYS have a fire extinguisher at hand when working on carburetors.
Drain the carburetors. There should be a screw on the lower side of each carb float bowl. Remove the screw then replace it after the fuel drains. Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, (not all bikes have a water trap bowl). Turn the gas back on and wait a minute for the carbs to fill with gas. If the bike doesn't start and run properly then shut off the gas and remove the carburetors from the engine.

FOR EACH carb > Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Before putting the slides back in the throat of the carbs, Move the clip on the jet needle one notch lower. Put the rest of the carb back together and install the carbs. Sync the carbs such that the slides on both carbs move at the same exact instant when the throttle is slowly turned from idle speed. This process should get you back on the road.


Please rate this solution. Thanks!

Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).

Drain the carburetor. There should be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.

Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Check the float as they can go bad and fill with gas such that they no longer float. Remove the idle screw and the air screw on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. The idle speed will probably different so adjust the idle screw to get back to where it was. This process should get you back on the road.

Please rate this solution. Thanks!

Drain the carburetors. There should be a screw on the lower side of each CARB float bowl. Remove the screw then replace it after the fuel drains. Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, (not all bikes have a water trap bowl). Install new stock NGK spark plugs.

Remove the CARBS from the bike.
FOR EACH CARB > Remove the float bowl and clean the entire CARB with a spray CARB cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the CARB. Remove the idle screw and the air screw on the outside throat of the CARB and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the CARB back together, clean the air filter and install the CARB. Install an in-line fuel filter. Let the float bowl fill then start the engine.

BALANCE THE CARBS
Turn the throttle screw on the LEFT CARB one half turn inward. Now start the engine and get it warmed up. With the engine running, remove the RIGHT spark plug wire. Adjust the idle speed on the left CARB to the point where the engine just can't quite stay running and dies. Now put the loose spark plug wire back into place.

Now turn the throttle screw on the RIGHT CARB one half turn inward. Restart and rev the engine. Next, remove the LEFT spark plug wire. Adjust the idle speed on the right CARB to the point where the engine just can't quite stay running and dies. Now put the loose spark plug wire back into place.

SYNCHRONIZE THE CARBS
Remove the air filter and rubber fittings to allow you to see into the throat of both CARBS. You may need a mirror to see inside. You need to be able to see the slides go up and down when you twist the throttle. Now turn the fitting where the cable goes into each CARB such that there is just a bit of slack in the cable, 1/16" is plenty. Lock ONE of the cable adjusters down tight. All further adjustments will be made on the other CARB.

With the motor turned off twist the throttle very slowly while looking at the slides. Both slides need to begin lifting at the exact same moment. If the slides don't raise at the exact same time then slowly twist the throttle until the locked adjuster slide just barely starts to move. Hold the throttle still and turn the adjuster on the other CARB so that the slide on that CARB just barely starts to move also. Now recheck the slide movement timing. Do this process until the slides on both CARBS begin to raise at the EXACT same moment. Lock down the loose adjuster and re-check the slides.

Turn the idle screw on each CARB EXACTLY ONE HALF turn outward and restart the engine. The engine will be probably be idling very fast. Adjust both the idle screws equally from this point to get to the desired idle speed. Congratulations, you have just balanced and synchronized your CARBS This should fix the problem. One last and VERY IMPORTANT thing, Have a fire extinguisher handy and ready for use any time you work on or with he CARBS.

Please rate this solution. Thanks throttlejock!

Turn off the gas and remove the water trap bowl at the bottom of the petcock, (gas valve). Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ). Get a set of the stock NGK spark plugs your bike came with. Check for spark on each cylinder before installing the plugs.

Now go to the idle and air screws on the outside of each of the carbs. IMPORTANT > > GENTLY turn both screws all the way in until they LIGHTLY seat. Now turn the screws EXACTLY one and one half turns outward.

SYNCHRONIZE THE CARBS
Remove the air filter and rubber fittings to allow you to see into the throat of both carbs. You may need a mirror to see inside. You need to be able to see the slides go up and down when you twist the throttle. Now turn the fitting where the cable goes into each carb such that there is just a bit of slack in the cable, 1/16" is plenty. Lock ONE of the cable adjusters down tight. All further adjustments will be made on the other carb.

With the motor turned off twist the throttle very slowly while looking at the slides. Both slides need to begin lifting at the exact same moment. If the slides don't raise at the exact same time then slowly twist the throttle until the locked adjuster slide just barely starts to move. Hold the throttle still and turn the adjuster on the other carb so that the slide on that carb just barely starts to move also. Now recheck the slide movement timing. Do this process until the slides on both carbs begin to raise at the EXACT same moment. Lock down the loose adjuster and re-check the slides.

BALANCE THE CARBS
Turn the throttle screw on the LEFT carb one half turn inward. Now start the engine and get it warmed up. With the engine running, remove the RIGHT spark plug wire. Adjust the idle speed on the left carb to the point where the engine just can't quite stay running and dies. Now put the loose spark plug wire back into place.

Now turn the throttle screw on the RIGHT carb one half turn inward. Restart and rev the engine. Next, remove the LEFT spark plug wire. Adjust the idle speed on the right carb to the point where the engine just can't quite stay running and dies. Now put the loose spark plug wire back into place.

Turn the idle screw on each carb EXACTLY ONE QUARTER turn outward and restart the engine. The engine will be probably be idling very fast. Adjust both the idle screws equally from this point to get to the desired idle speed. Congratulations, you have just synchronized and balanced your carbs.

PLEASE RATE THIS SOLUTION. Thanks!