Question about Harley Davidson FLSTC Heritage Softail Classic Motorcycles

1 Answer

1996 Harley Davidson FLSTC Heritage Softail Classic how to install front fork lowering kit

1996 FLSTC how to remove top nut to install a lowering drop in kit @

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    One Above All:

    The expert with highest point at the last day of the past 12 weeks.

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

  • Harley Davidson Master
  • 53,441 Answers

Hi, Michael for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
https://www.youtube.com/watch?v=tPyfEHSkmHs http://www.mediafire.com/file/br4waxbyxcya9zk/84+to+99+Harley+Softail+Service+Manual.pdf http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
https://www.harley-davidson.com/shop/harley-davidson-owners-manual
https://www.6ya.com/ to speak to me personally $6

Posted on Jan 13, 2019

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
gregg201
  • 53441 Answers

SOURCE: 2003 Harley Davidson FLSTC - FLSTCI Heritage Softail Classic how to change the lower fork legs

Hi, Toolbox77 for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can not find the best tool you ever bought for your Harley, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below and for more specific information or questions at no charge please feel free to contact me at xlch@mail.com. Good luck and have a wonderful day.
Harley Fork Sliders Removal Fix My Hog
Chrome Lower Fork Sliders
Harley Davidson Touring Workshop Service Repair Manual 2003 $10 includes a free $60 electrical diagnostic manual
http://partsfinder.onlinemicrofiche.com/ronnies/showmodel.asp?make=hdmc
http://mybikemanuals.com/harley-davidson/2005-harley-davidson-owners-manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Posted on Mar 25, 2018

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's the best way to remove steering column cover on my 1996 Ford contour. I need to fix my turn signal switch


Look underneath. There is USUALLY, 4 screws set in recesses. The top raises and the lower part drops down exposing the switches.

Nov 19, 2015 | Ford Cars & Trucks

1 Answer

Speedometer on 1996 softail not working


Hi Anonymous, try this: remove and clean your speed sensor located on the right hand side of gear box between the top cover and the starter motor end cap. Good luck

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Apr 18, 2014 | 2000 Harley Davidson FLSTC Heritage...

1 Answer

How do i spread the lower triple tree so i can install the fork? FLSTC


Hi Anonymous, normally they go in with no trouble, you might have a mushroomed fork tube cap. You can bang in a long tapered chisel at the pinch slot after removing pinch bolts to facilitate instalation.Good luck

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Apr 08, 2014 | 2000 Harley Davidson FLSTC Heritage...

1 Answer

To remove 1993 mustang conv. top cylinders should top be up or down? thanks, bill


don't have 93. here's 94

Motor Assembly, Convertible Top Removal and Installation
NOTE: The folding top hydraulic cylinder rods should be in the fully retracted position.
Use absorbent rags or a container to catch any hydraulic fluid that leaks out when removing the fittings.
  1. Remove motor and pump assembly as outlined.
  1. Loosen each folding top motor upper and lower hose fitting on the sides of the folding top hydraulic lift motor and plate kit (533A00) .
  1. Remove the folding top hydraulic lift motor and plate kit .
  1. Remove each of the service folding top hydraulic lift motor and plate kit plugs one at a time and attach the tee fitting to the replacement folding top hydraulic lift motor and plate kit . NOTE: Make sure that the o-ring is installed in the bottom of each folding top hydraulic lift motor and plate kit port before attaching the hose tee fitting.
  1. Connect the folding top hydraulic lift motor and plate kit unit to a 12-volt power source and cycle the folding top hydraulic lift motor and plate kit in and out several times to purge the air from the folding top motor upper and lower hoses (53390) . Some noise squeal may be noticed due to the air. srb~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not overfill or the reservoir seal could be blown out.
  1. Carefully remove the rubber fill plug from the back and the reservoir and check the fluid level. The level should be at the bottom of the filler hole. If necessary, add Synthetic Mercon® Multi-Purpose Automatic transmission fluid E6AZ-19582-B (ESR-M2C163-A2) or equivalent.
  1. Replace the fill plug with a new fill plug.
  1. To install, reverse Removal procedure.
-------------------------------------------------------------------------------------------------------------------------------
Section 01-17: Convertible 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Lift Cylinder, Power Top Removal and Installation
NOTE: The cylinder rods should be in the fully-retracted position.
  1. Remove pump and motor as outlined.
  1. Remove the upper and lower hose fitting from the folding top hydraulic cylinder (50600) . Use absorbent rags or a container to catch any hydraulic fluid that leaks out when removing the fittings.
  1. Remove each of the service cylinder plugs one at a time and attach the hose fittings. NOTE: Be sure each fitting is installed in the correct position on the folding top hydraulic cylinder .
    NOTE: Make sure that the tetra seal is installed in the bottom of each of the folding top hydraulic cylinder ports before attaching the upper and lower hose fittings.
  1. Connect the folding top hydraulic lift motor and plate kit (533A00) to a 12-volt power source and cycle the folding top hydraulic lift motor and plate kit in and out several times to purge the air from the hoses. Some noise squeal may be noticed due to the air.
  1. Carefully remove the rubber fill plug from the back and the reservoir and check the fluid level. The level should be at the bottom of the filler hole. If necessary, add Synthetic Mercon® Multi-Purpose Automatic transmission fluid E6AZ-19582-B (ESR-M2C163-A2) or equivalent.
  1. Replace the fill plug with a new fill plug.
  1. To install, reverse Removal procedure.

Jan 21, 2011 | Ford Mustang Cars & Trucks

2 Answers

1997 Evinrude 50 HP SPL. I have removed all the bolts holding the lower rnd to the engine, it seems to be hanging up on the shify shaft, and I can't find a way to drop the unit. It drops down about...


Okay this is on total memory. The shift shaft for a lot of those engines goes right up through the pilot shaft and exits just in front of the block under the carburetor(s). You will see the **** linkage arm connected to this shaft sometimes it's double nutted. See if you can slide the lower unit back up to the housing and put a bolt in it to hold then undue the shift shaft linkage, Remove the bolt and drop the lower unit. Be careful of the water tubes and check make sure the rubber grommets are in place in the pump housing not on the tubes. Clean up the pump housing and install the new impeller kit.
Put the impeller down the shaft on top of the impeller plate, lightly grease the inside of the housing the impeller plate and impeller. Then lower the pump housing down to the impeller while turning the drive shaft clockwise lightly push down on the impeller housing. This will fold the impeller blades all in the correct position and provide lubrication to the pump until the water gets into the pump. To make life easier re-grease the drive shaft spline and the water tube grommets this will ad ease in reinstalling the lower unit. be careful to make sure you thread the drive shaft, water tubes and shift shaft all in at the same time. After installation you may find you need to adjust the **** linkage.

Dec 11, 2010 | Boating

2 Answers

How do i change a thermostat on a 1996 mercury sable and whre is it located


Thermostat-follow the upper radiator thick hose to the thermostatic housing. Removal & Installation 3.0L (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions in the beginning of this section.
  2. Drain the engine cooling system into a suitable container.
  3. Remove the three thermostat housing bolts.
  4. Remove the thermostat O-ring seal.
  5. Inspect and clean the sealing surfaces.
To Install:
  1. Install thermostat and o-ring seal.
  2. Install thermostat housing bolts; torque to 9 lb-ft (12 Nm).
  3. Refill cooling system.
  4. Warm-up vehicle and check for leaks.
  5. Top off cooling system.
3.0L (4V) To Remove:
  1. Drain the engine cooling system.
  2. Disconnect the lower radiator hose from the water inlet adapter.
  3. Remove the bolts, the water outlet adapter and thermostat. Discard the O-ring seal.
To Install:
  1. Clean the sealing surfaces.
  2. Install the thermostat with a new gasket. Tighten the bolts to 89 in-lb (10 Nm).
  3. Refill the cooling system.
  4. Warm-up the vehicle and check for leaks.
  5. Top off the cooling system.
3.4L (SHO) To Remove:
  1. Drain the engine cooling system.
  2. Remove battery.
  3. Remove power distribution box.
  4. Remove battery tray.
  5. Disconnect upper radiator hose and place it out of the way.
  6. Disconnect the lower radiator hose from the water inlet connection.
  7. Remove the two mounting bolts and remove the water inlet connection.
  8. Remove the O-ring seal and thermostat from the water pump.
  9. Inspect O-ring for damage and replace if necessary.
To Install:
  1. If necessary, install a new O-ring on the inlet connection.
  2. Install the thermostat in the water pump and install the inlet housing. Tighten the bolts to 71-106 lb-in (8-12 Nm).
  3. Connect the lower radiator hose to the water inlet connection.
  4. Install the upper radiator hose.
  5. Install battery tray.
  6. Install the power distribution box.
  7. Install the battery.
  8. Refill the engine with coolant.
  9. Start the engine and allow the engine to warm up so that the water thermostat opens. Check for leaks.
  10. Stop the engine. Allow the engine to cool and top off degas bottle as required to maintain minimum cold fill level.
prev.gif next.gif

Aug 03, 2010 | 1996 Mercury Sable

1 Answer

Need to remove front of dryer to install propane conversion kit. model dlg5966


Remove top 3 screws in back, Slide top ack 2-3" and lift off.
Remove control pnl.
Remove front panel.
Gas valve is in the lower right corner.
Follow conversion instructions.

Jan 11, 2010 | LG Dryers

1 Answer

I need to remove the harmonic pully on a 1996 avenger so i can replace the timing belt.


  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle. Remove the right side wheel and tire assembly.
  3. Remove the right inner splash shield.
  4. Remove the accessory drive belts.
  5. Break the crankshaft damper bolt loose, but do not remove it.
  6. Remove the crankshaft damper. If necessary, attach a suitable 3-jawed puller to the crankshaft damper, then tighten the center bolt and remove the damper bolt and damper.



0900c152800896d6.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Remove the right side inner fender splash shield


0900c152800896d7.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: From below the vehicle, remove the accessory drive belts


0900c152800896d8.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: If necessary, use a prying tool to wedge between the engine block and damper spoke hole, then loosen the center bolt


0900c152800896d9.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 4: Remove the crankshaft damper center bolt and washer


0900c152800896da.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 5: Pull off the crankshaft damper, or remove using a 3-jawed puller tool
To install:
  1. Install the crankshaft damper. It may be necessary to install the crankshaft damper using an M12-1.75 x 150mm bolt, washer, thrust bearing and nut from the crankshaft damper installation tool kit 6792 or equivalent.
  2. Install the crankshaft damper bolt and tighten to the following specifications:

    2.0L SOHC and DOHC engines-105 ft. lbs. (142 Nm). 2.4L engine-100 ft. lbs. (135 Nm) 2.5L engine-134 ft. lbs. (182 Nm)
  3. Install the accessory drive belts.
  4. Install the right inner splash shield. Install the right side wheel and tire assembly.
  5. Carefully lower the vehicle, then connect the negative battery cable.

icn_arrow.gifBack to Top

Jul 10, 2009 | 1996 Dodge Avenger

1 Answer

One part of agitator moves the other part doesnt.


Two-Piece Agitator: Bottom Works, Top Does Not - Whirlpool brands

Some Whirlpool brands washing machines employ a two piece agitator. The bottom is call the agitator and the top is usually referred to a 'Mover'. A multi-piece cam and bearing assembly connects the two and allows the top portion to index.

If the bearing or cams become stripped or damaged, the mover will often not work. Fortunately, Whirlpool produces a cost effective agitator repair kit that replaces all of the critical components in this cam assembly. There are three different repair kits. They differ in the height of the cam.
35c14d6.jpg

Agitator Removal Instructions:


Remove Dispenser or Cap:
Some models of washing machines utilize a fabric softener dispenser that resides on top of the agitator. This dispenser simply snaps onto the top of the agitator. Other styles utilize a decorative cap. To remove the dispenser, simply grab it and firmly pull up. To remove the agitator cap, insert a small flat-head screw driver into the seam between the agitator cap and the upper agitator (mover). Use a twisting or prying action to pop the cap off of the agitator.

Remove Internal Debris Cap:
Inside the agitator you will see a cap with a raised handle, much like that of your automobile. Simply reach into the agitator and twist the cap while pulling up. This will remove the cap and its o-ring.

Remove Agitator Stud:
When looking into the agitator assembly, you will notice a single nut in the center of the agitator. Use a socket kit or nut driver to remove this bolt (agitator stud).

Remove the Upper Agitator (Mover):
With the bolt removed you should be able to remove the upper half of the agitator (mover) by simply pulling up. Sometimes pulling up will actually remove the whole agitator assembly. If this happens, place the Lower Agitator on the floor and stand on the flat lip. Then Pull up to separate the Upper Agitator (mover) from the Lower Agitator.

Remove the Cam and Clutch Dogs:
When you remove the upper agitator (mover) it contains the cam and clutch dogs. Tun the assembly upside down. The cam and dogs should then come out.

-- Stop Here if Replacing Cam Kit --

Remove O-ring:
The lower agitator remains on the transmission shaft. On the top of the agitator, there is an o-ring. Remove this o-ring.

Pull the Lower Agitator:
All that remains is the lower agitator. This can be removed by simply pulling straight up on the agitator.


Agitator Installation Instructions:

Set Lower Agitator:
Slide the lower agitator onto the transmission shaft. Rotate the lower agitator until the splines in the shaft match those in the agitator. Once aligned press the agitator down. Install the o-ring into the top of the lower agitator.

-- Start Here if Replacing Cam Kit --

Assemble Cam and Dogs:
Turn the cam upside down. Place the small round ear of the dog into the corresponding slot on the cam. Repeat this for each of the four cams.

Install Cam and Dogs into Upper Agitator:
Invert the Upper Agitator (mover) and slide the cam/dog assembly inside. The cam should be pushed into the mover until it shoulders. Then rotate the whole assembly upright.

Install the Upper Agitator (Mover) on the Lower Agitator:

The lower agitator has two tabs that stick up that are 180 degrees apart. These tabs fit into two slots on the bottom of the cam. Align the matching tabs and slots and place the Upper Agitator (mover) and cam assembly onto the lower agitator. Push down until the cam snaps onto the Lower Agitator. If the dogs fall out during this step it is necessary to return to the 'Assemble Cam and Dogs' section above and start over.

Install the Agitator Stud:
Place the bolt (agitator stud) into the hole in the bottom center of the cam. Use a socket kit or nut driver to tighten the bolt .

Install Internal Debris Cap:
Install the o-ring into the groove on the OD of the debris cap. With the o-ring in place, push the cap into the Upper Agitator (mover). It is important that the cap is pushed past the ports in the Upper Agitator (mover) so that the wash water can enter and exit as designed.

Install the Dispenser or Cap:
The final step is to replace the top cap. Both the cap and the dispenser simply snap into place. Just make sure they are installed as far down a they will go and are firmly in place.



Apr 07, 2009 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Convertible top


here's some info

Symptom Chart Condition Possible Source Action
  • Folding Top Does Not Raise and/or Lower
  • Blown fuse(s).
  • Circuitry open/shorted.
  • Damaged folding top switch.
  • Damaged raise/lower relay .
  • Damaged folding top hydraulic lift motor and plate kit .
  • Parking brake not engaged.
  • Go to Pinpoint Test A.
  • Top Hesitates and/or Comes Up Uneven
  • Damaged folding top hydraulic lift motor and plate kit .
  • Damaged folding top motor upper and lower hose .
  • Damaged folding top hydraulic cylinder .
  • Damaged folding top linkage.
  • Go to Pinpoint Test B.
  • Top Does Not Raise or Does Not Go All the Way Up
  • Damaged folding top linkage.
  • Damaged folding top hydraulic lift motor and plate kit .
  • Go to Pinpoint Test C.
  • Hydraulic System
  • Damaged fluid reservoir.
  • Damaged folding top hydraulic cylinder .
  • Damaged folding top motor upper and lower hose .
  • Go to Pinpoint Test D.


Lift Cylinder, Power Top Removal and Installation
NOTE: The cylinder rods should be in the fully-retracted position.
  1. Remove pump and motor as outlined.
  1. Remove the upper and lower hose fitting from the folding top hydraulic cylinder (50600) . Use absorbent rags or a container to catch any hydraulic fluid that leaks out when removing the fittings.
  1. Remove each of the service cylinder plugs one at a time and attach the hose fittings. NOTE: Be sure each fitting is installed in the correct position on the folding top hydraulic cylinder .
    NOTE: Make sure that the tetra seal is installed in the bottom of each of the folding top hydraulic cylinder ports before attaching the upper and lower hose fittings.
  1. Connect the folding top hydraulic lift motor and plate kit (533A00) to a 12-volt power source and cycle the folding top hydraulic lift motor and plate kit in and out several times to purge the air from the hoses. Some noise squeal may be noticed due to the air.
  1. Carefully remove the rubber fill plug from the back and the reservoir and check the fluid level. The level should be at the bottom of the filler hole. If necessary, add Synthetic Mercon® Multi-Purpose Automatic transmission fluid E6AZ-19582-B (ESR-M2C163-A2) or equivalent.
  1. Replace the fill plug with a new fill plug.
  1. To install, reverse Removal procedure.
-----------------------------------------------------------

Jan 04, 2009 | 1989 Ford Mustang

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Gar
Gar

Level 2 Expert

384 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5809 Answers

Mike

Level 3 Expert

4356 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...