Head torque specs xr650l - XR 650 L Honda Motorcycles

SOURCE: Need cylinder and cylinder head torque specifications 98 XR 250

you dont need torque specs on that just use a 1/2 inch drive with you 14mm or16mm socket hold the wratchet right at the top and tighten it as tight as you could get it like that then use wratchet in normal position and just give it a little snugg it will be perfect i have done it a million time on the same type of bikes...

SOURCE: 93 artic cat jag head torque pattern and specs

the best place to find it is the service manual. if not avail. i usually 1, tighten it to ~10-20Nm in a 'outwards spiral' fashion, ie start tightening from centre bolts outwards. 2, spiral tighten by 1/4 turn, 3, another 1/4 turn, and 4, final 1/4 turn.

SOURCE: What are the torque specs for the cylinder head...

http://www.servis.offmoto.com/Manualy/KTM/2008/KTM%20125_200_250_300%20SX_EXC_XC-W%20Service%20info%20-%202008/KTM%20125_200_250_300%20SX_EXC_XC-W%20Service%20info%20-%202008.rar

I think you will like this.

David Belcher

• 1978 Answers
• Posted on May 23, 2010

SOURCE: what is the torque specs 86 goldwing 1200

6mm bolts

ft-lbs 7-10

8mm bolts

ft-lbs 37-40

SOURCE: CYL HEAD BOLT TORQUE SPEC AND CAM HOLDER BOLT

Thank you for contacting FixYa with your inquiry. I have been going
over some of the older help requests that have been archieved and
trying to provide solutions for those that didn't get answered. Hope
this information helps.

KTM Torque settings

1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
13. Shock absorber bottom Shock absorber bottom bolt 60Nm 44ft lbs
14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
17. Engine brace Engine brace 33Nm 24ft lbs
18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
19. Spoke nipple Spokes 5Nm 4ft lbs
20. Other Screws on chassis M6 10Nm 7ft lbs
21. M8 25Nm 19ft lbs
22. M10 45Nm 33ft lbs
23. Other collar nuts on chassis M6 15Nm 11ft lbs
24. M8 30Nm 22ft lbs
25. M10 50Nm 37ft lbs
26. Front Sprocket 44ft lbs