Service manual headlamp spring

wow no year car told,why? 1998 to now, is it USA? car?
yes sold in S.America too, 2011 and up.
the outside casing lens?
the service manual covers this only
no problem told at all just how to. ( so I guess the whole thing out and in)
why skip saying the problem first.? to the blind.
is the front of the light casing all ugly and yellow?
2001-2008 (separate model, North America)
so I guess 2003, ( using ESP and Karnac mind meld)

replacing all this.??????

https://www.rockauto.com/en/catalog/chevrolet,2003,trailblazer,4.2l+l6,1412277,body+&+lamp+assembly,headlamp+assembly,10762

PULL steps

Headlamp Replacement (TrailBlazer) Removal Procedure

1. Open and support the hood.
2. Remove the grille. Refer to ' Grille Replacement (Chevrolet).
3. Use a flat-bladed tool in order to release the clips that retain the grille to the headlamp panel.
4. Remove the grille from the vehicle.
5. Pull up on the retaining tabs?(1) in order to remove the headlamp assembly from the headlamp panel.
6. Disconnect the headlamp leveling electrical connector from the motor/actuator if equipped.
7. Disconnect the headlamp electrical connector?(2) from the headlamp assembly.
8. Remove the side marker socket?(4) from the headlamp assembly.
9. Remove the park/turn socket?(3) from the headlamp assembly.
10. Remove the headlamp assembly from the headlamp panel.

if confused buy the service manual
or get the car serviced in real shop.

There are two spring clips located under the hood around each headlamp housing. Open both clips and extract the headlamp housing from the front of the car by pulling the plastic assembly by grabing the edges by the black rubber seal. The entire headlamp housing will pull out from the front bumper enough to allow you to change the bulbs. Repeat procedure and clip the spring clamps back in place.

There are two spring clips located under the hood around each headlamp housing. Open both clips and extract the headlamp housing from the front of the car by pulling the plastic assembly by grabing the edges by the black rubber seal. The entire headlamp housing will pull out from the front bumper enough to allow you to change the bulbs. Repeat procedure and clip the spring clamps back in place.

There are two spring clips located under the hood around each headlamp housing. Open both clips and extract the headlamp housing from the front of the car by pulling the plastic assembly by grabing the edges by the black rubber seal. The entire headlamp housing will pull out from the front bumper enough to allow you to change the bulbs. Repeat procedure and clip the spring clamps back in place.

lift the bonnet and look behind the headlamp in question, there will be a few nuts that are holding the assembly to the front apron, remove them and also the electrical plug from behind the headlamp.
if it is only a bulb you have to replace you will find that where the electrical plug connects to the rear of the headlamp there is a rubber weatherproof boot which you remove, it will expose the rear of the halogen bulb, there will be a little metal spring type arm retaining the bulb,push the end of the spring towards the back of the headlamp and to the side and let it come back away from the headlamp, this will let the bulb come out and you replace it with the new bulb and replace the items in reverse order

SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Headlamp Bulb Printable View (327 KB) Freestyle, Five Hundred
Item Part Number Description 1 — Headlamp bulb electrical connector (part of 14290) 2 13N021 Headlamp bulb

Montego
Item Part Number Description 1 — Headlamp bulb access cover screws (6 required) (part of 13006) 2 13N019 Headlamp bulb access cover 3 — Spring retainer (part of 13006) 4 13N021 High intensity discharge (HID) bulb 5 14A411 HID bulb electrical harness 6 — High beam bulb electrical connector (part of 13006) 7 13N021 High beam bulb Removal and Installation
WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury.
NOTE: The headlamp bulb should not be removed from the headlamp assembly until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp assembly where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp assembly.
NOTE: Make sure the headlamp switch and ignition switch are in the OFF position.
Freestyle, Five Hundred

1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
   • Disconnect the electrical connector.

Montego

1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly — Five Hundred, Montego in this section.

1. Remove the 6 screws and the headlamp bulb access cover.

Montego high beam bulb

1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
   • Disconnect the electrical connector.

Montego HID bulb

1. Release the spring retainer and remove the HID bulb.
   • Disconnect the electrical connector.

All vehicles

1. To install, reverse the removal procedure.

There's a spring clip inside the hood compartment that holds the headlamp assemby in position. Release the spring clamp, grab around the edges of the headlamp where it meets the front fender and pull the headlamp assembly out of it's socket. Replace the bulb from the back of the headlamp assembly and reposition the headlamp assembly back into the socket. Once properly position replace tension of the spring clamps inside the hood.

your owner manual will list the bulb. It is expensive. tascafordparts.com for discount from Ford Dealer

here's 2003, don't have 2004

Navigator high intensity discharge (HID) headlamp

1. Remove the front radiator air deflector.

1. Remove the three bolts and the headlamp assembly.
• Disconnect the electrical connectors.

8. Remove the headlamp bulb protective cover(s).

• Remove the HID lamp cover.
• Remove the high beam cover.
• Disconnect the electrical connector and push the grommet into the headlamp assembly.

1. Release the spring tabs and remove the HID low beam bulb.

i believe it is held in by a spring underneath the rubber boot the spring swings over like a door and hooks in a notch

Is the car lowered? mine does that too but is has 1.4 inch lowering springs. i readjusted the hight of the lights manually and they work fine now.