Suzuki Motorcycles - Page 2 - Recent Questions, Troubleshooting & Support

0helpful
1answer

SUZUKI VL 125 Intruder. Where is the neutral switch on a VL 125 please?

Question edited for clarity, full make and model name. Question moved to model category. https://www.google.com/search?q=SUZUKI+VL+125+Intruder+replace+neutral+switch This is what it looks like

SUZUKI VL125 INTRUDER 2001-2007 NEUTRAL SWITCH

eBay https://www.ebay.co.uk > itm SUZUKI VL125 INTRUDER 2001-2007 NEUTRAL SWITCH ; Quantity. 1 available ; Item number. 394596274518 ; Brand. Suzuki ; Manufacturer Part Number. NEUTRAL SWITCH ; Est. £17.50 Service Manual https://www.manualslib.com/manual/804522/Suzuki-Vl125.html?page=193&term=neutral+switch&selected=1#manual ..Likely to be similar
9/19/2023 12:09:00 AM • Suzuki VL 125... • Answered on Sep 19, 2023
0helpful
1answer

2000 Marauder. It turns over. Why doesn't it crank?

If it runs on starter fluid that means it's not a spark issue. This is most likely a fuel starvation problem. You need to start at the tank and work all the way through the fuel system all the way to the cylinder. If your getting fuel at the filter go to the next part in the system and check for fuel from that point. When was the Carburettor last serviced? A dirty/worn jet or a dirty/worn float needle can cause issues. Try this. Don't use starter fluid. Spin the engine over for 2 to 3 seconds. Turn the Ignition Off. Remove a spark plug and look at it. Your checking to see if it's wet with fuel. Giving it a sniff sometimes helps. Refit that plug and repeat this for the other cylinder. If they are wet the engine is getting fuel. Check your air filter. You'll be surprised how much trouble a dirty one can cause. If these all check out OK check the fuel pump relay. If it's faulty it won't turn on the fuel pump when you try to start the bike.
9/12/2023 8:13:10 PM • Suzuki... • Answered on Sep 12, 2023
0helpful
1answer

Have a 97 Suzuki Intruder 1400 and it sounds like it's not getting gas. Where is the fuel filter and is could this be the problem

What EXACTLY is it doing to make you think it isn't getting fuel? This model does not have a separate fuel filter. The fuel tap on actual tank, (the petcock), has a gauze filter built into it inside the tank. These can sometimes clog up over time especially if it's had bad gas through it or it's been stood for a while. When was the last time the Carbs were serviced? This could be as simple as a dirty fuel jet or a dirty/worn needle. If your going to clean the gauze filter make absolutely sure the tank is empty BEFORE you remove any fuel lines or the petcock. I found that an old, stiff bristle toothbrush works well to clean the gauze.
9/12/2023 7:44:29 PM • Suzuki... • Answered on Sep 12, 2023
0helpful
1answer

My suzuki marauder started licking oil real bad from the back end of the motor when started, does anybody know what that is and how to fix it

limited info generic answer depending on area of leak cann be anything --rear seal --valve cover gaskets --oil filter --oil lines [if oil cooler --crack in block -need to wipe area and observe where leak is
9/5/2023 10:35:18 PM • Suzuki... • Answered on Sep 05, 2023
0helpful
1answer

2008 Suzuki GSX-R 750. How do I clear a C42 trouble code on a 2008 gsxr 750 after replacing ignition please?

Question edited for clarity. Question moved to model category. A C42 is an error in the ignition system that uses a 100 Ohm resistor to prevent hot wiring the bike. The usual problem is a connection to the ignition switch gets loosened or broken so the resistance value is greater than 100 Ohms.

C42 Error Code: Exhausted Many Options - StromTrooper

.. Lots more here. It is a known issue https://www.google.com/search?q=2008+Suzuki+GSX-R+750+C42+code ..
9/3/2023 11:01:56 PM • Suzuki GSX-R 750... • Answered on Sep 03, 2023
0helpful
3answers

Fuse box

The main fuse is under the panel on the right side behind the forks and the rest of the fuses are in the crank case under the cover...where you fill the oil.
9/3/2023 2:40:58 PM • 2004 Suzuki VL... • Answered on Sep 03, 2023
0helpful
1answer

2001 Suzuki intruder VL 1500 clutch kit

8/30/2023 3:29:19 PM • Suzuki... • Answered on Aug 30, 2023
0helpful
1answer

1986 Suzuki RM80. How much fork oil does my 1986 Suzuki RM80 call for?

Question edited for clarity. RM85 Fork Specs. Bound to be the same forks When adjusting the fork oil level, compress the outer tube fully without the fork spring. ? 09943-74111: Front fork oil level gauge ? Fork oil level (Standard): 124 mm (4.88 in) ? 99000-99001-SS5:SUZUKI FORK OIL SS-05 ? Standard fork oil capacity (each leg): 351 ml or an equivalent fork oil (11.86/12.36 US/lmp oz Free Service manual for the RM85 https://www.manualslib.com/manual/824675/Suzuki-Rm85.html?page=164&term=fork+oil&selected=1#manual Lots of Service Manuals for around $34 https://www.ebay.com/itm/385931112664?hash=item59db4970d8:g:WyUAAOSwkFpj2-n~ More here. https://www.google.com/search?q=1986+suzuki+rm80+service+manual ..
8/23/2023 4:46:48 AM • Suzuki... • Answered on Aug 23, 2023
0helpful
1answer

2005 Suzuki VL1500 Intruder. Where is the tip over bank angle sensor at on my 2005 LV1500 please?

Question edited for a lot mode clarity, and add maker and model name. It is a VL for 'Volusia', not an LV1500. Question moved from Power Motorcycles. The Tip Over Sensor is under the seat. From the Service Manual, the last link When the motorcycle tips over, the tip-over sensor sends a signal to the ECM. Then, this signal cuts OFF current supplied to the fuel pump, fuel injectors and ignition coils. Sensor G on Page 30. Page 70 shows a picture of it TO SENSOR INSPECTION The tip-over sensor is located under the front seat. (Page 70) https://www.google.com/search?q=suzuki+vl1500+intruder+tip+over+sensor+location

tip-over sensor reset - M109 Rider Forums

m109riders.com https://www.m109riders.com > ... > M109R Shop Talk Usually all you do is sit the bike back up, then make sure the k-switch is on (run position), then cycle the ignition to off-on-off again.... Missing: vl1500 ‎' Show results with: vl1500

Help needed with 1500 Intruder

Motorcycle Forum https://www.motorcycleforum.com > threads > help-ne... Jun 7, 2021 - The repair manual shows that there is a tip over switch under the seat. I have a fuel filter exactly where the switch is shown in the book. I am ...

REsetting Tip Over Sensor

Adventure Rider https://www.advrider.com > threads > resetting-tip... Aug 30, 2006 - According to the Service Manual, the tip over sensor is to deliver a 3.7 - 4.4 volt signal to the ECU, or the bike will not start. Missing: vl1500 ‎intruder

VL1500 Service Manual

Crowitis http://www.crowitis.com > images During deceleration, the fuel injection time. (volume) is decreased. SIGNAL. DESCRIPTION. TIP-OVER SENSOR SIGNAL. (FUEL SHUT-OFF). When the motorcycle tips over ... 181 pages ..
8/23/2023 1:27:00 AM • Suzuki VL 1500... • Answered on Aug 23, 2023
0helpful
1answer

Hi how do I bypass the rev limiter on a 2001 Suzuki Bandit 1200?

Check out the link (I deleted the AI Answer Bot Answer... useless) https://www.google.com/search?q=bypass+the+rev+limiter+on+a+2001+Suzuki+Bandit+1200 ..
8/21/2023 7:19:22 PM • 2001 Suzuki GSF... • Answered on Aug 21, 2023
0helpful
1answer

How to adjust clutch 1998 Suzuki VL 1500 intruder

The clutch on this model is hydraulic and is 'self adjusting", if the clutch is slipping the plates are worn out and in need of replacement. This information comes directly from the factory service manual.
8/19/2023 4:42:06 AM • 2000 Suzuki VL... • Answered on Aug 19, 2023
0helpful
1answer

2006 Suzuki Boulevard C50 V800 Trike. My brake lights don't work and my running lights at night don't work. I checked fuse and light bulbs but they are all good.

Question edited for clarity. Question moved to model category. The problem with a Trike is that the wiring will be custom. For the brake light, check the switch with a multimeter for continuity. For the lights look for a break in the wiring. There may also be a relay involved in the running lights. https://www.google.com/search?q=2006+suzuki+boulevard+c50+service+manual+pdf ..
8/8/2023 4:11:46 AM • 2006 Suzuki... • Answered on Aug 08, 2023
0helpful
1answer

2003 Suzuki Marauder GZ125 K3. Hello, what are the valve clearances please?

Question edited for clarity. Question moved to model category.

2006 GZ125 Valve Clearance *update

Bike Chat Forums https://www.bikechatforums.com > viewtopic Sep 29, 2012 · 7 posts · 4 authors Now, according to Haynes, the clearances on the valves should be between 0.003" and 0.005". To me, that means 0.004" should be just about bang ... Missing: 2003 ‎specs Full parts list just because I found it. http://www.motocykle125.pl/wp-content/uploads/2016/02/suzuki_gz-125_125cc-gz125-ap131-1998-2000.pdf Service Manual https://www.google.com/search?q=2003+suzuki+marauder+gz125+service+manual ..
8/6/2023 11:04:31 PM • Suzuki GZ 125... • Answered on Aug 06, 2023
0helpful
3answers

My 2003 Suzuki ltz400 will not fire. We switched the stator, no fire. Got a new coil, no fire. Changed the cdi box, and still yet no fire. What else could it be?

Can only be compression to low or no fuel being allowed to motor. why did you change all the electric items did it have no spark at plug ??? Anyhow safe to say ignition is fine as all is replaced but worth confirming you have spark at plug (turn motor over with plug out and see if sparks) before we assume its compression or fuel delivery issue.when you have plug out cover the plug hole with finger to seal it best you can and turn over motor couple of times if you can keep it sealed or nearly sealed then way low on compression and that would be the problem (it should force your finger off and you would have no chance to hold it if compression is adequate) if compression is good then you left will fuel issues.. I know sounds stupid but check all the silly stuff first before you dive right in to all the nuts an bolts. disconnect fuel line see fuel is flowing from tank, check breather hose on tank not kinked or blocked, if you know fuel in it is old throw away and stick new fuel in, if all this checks out good then open her up.you could also force feed it fuel couple of tea spoons of fuel in the spark plug hole put it back together to start it and see if you get a brief starter or try to start up out of her I know its another back yard test as my back yard compression test is but at least it isolates some areas to work on.. cheers matewww.motoxpartsonline.com
8/6/2023 12:11:35 AM • Suzuki... • Answered on Aug 06, 2023
0helpful
2answers

2000 Suzuki VS1400 Intruder. What are the pilot jet sizes please?

Question edited for clarity. Question moved to model category. Pilot Jet information https://www.google.com/search?q=2000+suzuki+intruder+1400+pilot+jet+size and your Service Manual

Suzuki Intruder VS1400 Service Manual

ManualsLib https://www.manualslib.com > ... > Intruder VS1400 View and Download Suzuki Intruder VS1400 service manual online. Intruder VS1400 motorcycle pdf manual download. ‎Engine - Tightening Torque · ‎Starter Clutch · ‎Wiring Diagram (The Others)

2000 Suzuki VS1400 Intruder Service Manual

servicemanualsgsxr.com https://servicemanualsgsxr.com > cruiser > 2000-suzuk... Service Manual 2000 Suzuki VS1400 Intruder, a great reference for the repair and maintenance. Service Manual, fix motorcycle yourself with a repair manual.
8/2/2023 3:52:53 AM • 2000 Suzuki VS... • Answered on Aug 02, 2023
0helpful
1answer

1983 Suzuki GS1100. When I start it, the oil light won't go off and it doesn't look like it is circulating in the eyeglass?

Question edited to add maker. Question moved from Cars and Trucks. Service Manuals

SUZUKI GS1100L 1980 SERVICE MANUAL Pdf Download

ManualsLib https://www.manualslib.com > ... > GS1100L 1980 View and Download Suzuki GS1100L 1980 service manual online. GS1100L 1980 motorcycle pdf manual download. Also for: Gs1100ex 1981, Gs1100ez 1982, ... https://www.google.com/search?q=1983+suzuki+gs1100+service+manual The pump is mechanical and pumps to the valves and other bearings that needs it. The oil level sight glass is only for that, you won't see it surging around like a washing machine. You have probably moved a wire when installing the new lights and that is causing the oil light to come on. If they are LED replacements, they can cause a whole lot of problems due to their electronic circuitry that is in the base cap of every bulb.. https://www.google.com/search?q=1983+suzuki+gs1100+installing+LED+Lights
7/27/2023 2:23:01 AM • Suzuki... • Answered on Jul 27, 2023
Not finding what you are looking for?
Suzuki Logo

16,018 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Suzuki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Sean Wright
Sean Wright

Level 3 Expert

2045 Answers

Bob G

Level 2 Expert

104 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...