20 Most Recent 2002 KTM LC4 625 Sc - Page 2 Questions & Answers

Hi, try to see this link and looking for the manual that you need. https://www.pdfmotomanual.com/manuales/ktm/eng I hope to give you an help. Luca

my ­b­est ­fr­i­e­n­d's s­ist­er-­i­n-­l­Aw ­m­A­k­es $74 ­ev­ery ­h­our ­o­n t­h­e ­c­o­m­put­er. S­h­e ­h­As ­b­e­e­n u­n­e­m­p­l­oy­e­d ­f­or t­e­n ­m­o­nt­hs ­but ­l­Ast ­m­o­nt­h ­h­er ­p­Ay­m­e­nt w­As $16505 just w­or­k­i­n­g ­o­n t­h­e ­c­o­m­put­er ­f­or ­A ­f­ew ­h­ours. ­g­o t­o t­h­is w­e­b s­it­e ­A­n­d r­e­A­d ­m­or­e ­g­o t­o t­h­is s­it­e ­h­o­m­e t­A­b ­f­or ­m­or­e ­d­et­A­i­l ... www.online-3.com

Hi, most likely your cdi unit or ignition coil needs replacing.

took me a min or two of WTF-ing to see pic and realize you meant a 2-stroke motorcycle..

try replace spark plugs

It's a bad seal of the head gasket. You need a new head gasket and to scrape every particle of debris from the cylinder head and cylinder surfaces that mate with the head gasket. Use the factory specified gasket sealing compound and do a clean job - no blobs or pools of the stuff. The head gasket should lay flat on the surface of the top of the cylinder, and you have to make this surface free of grit, leftover sealant and any other foreign matter before you put the head in place and torque it down. Start with the head bolts just finger tight and then go by the manufacturer's specs for the pattern and amount of torque to be applied. Usually it is recommended that you get to the specified torque amount in stages, going around several times and repeating the torque pattern until you get that maximum rated amount. This will prevent the seal from shifting or warping and should make the gasket seal perfectly. This is the old school method of doing this job. and I have never seen this fail to produce good results. Take your time, be clean, and you will have the results you want.

Check the clutch, adjust, clean, or replace

over full sump fuel getting into sump badly worn rings allowing excessive blow by

Worn out shift dogs.

Make sure cables are working . Follow it down to clutch and make sure clutch lever is actually moving. It is does then pull clutch in and pushbike backwards. Should release If not , plates are probably frozen through excessive heat. Replace them. If lever does not move when clutch handle pulled, then adjust or broken cable. hope that' it, easier and cheaper!

Make sure the wires on the other side of the relay box are holding when you push the relay in.

Have you tried an emissions test? That can tell you a lot about how the combustion is doing, and what you would need to adjust at the carburetor. Have you checked the spark plugs?

unfortunately the most cmmn cause for a bike not starting ff the kick start but starting with a bump is being too low on compression,although to you foot it may feel like enough it does need to be nearly 100% as high as it should be to kickstart.the easiest way to check the condition of the piston is to take the exhaust off and look up the port in the barrel ,it is usually the exhaust side of the piston that gets damaged as it gets hotter.good luck.Adam

Check for a positive wire being grounded against the frame or you are using the wrong bulbs.